Larson Electronics HALPRM-PS-1000WMH User manual

HALPRM-PS-1000WMH
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
1000 Watt Metal Halide Light - Pulse Start Ballast
Class 1 Division 2 Groups A-D - T3b Temperature - 110,000 lumens
Instruction Manual
WARNING
To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected and maintained by a
qualified electrician only, in accordance with all applicable electrical codes.
To avoid electric shock:
Be certain electrical power is OFF before and during installation and maintenance.
Luminaire must be connected to a wiring system with an equipment-grounding conductor.
Make sure the supply voltage is within the luminaires’ voltage rating.
This luminaire is designed for outdoor lighting service, and should not be used in areas of limited ventilation, or in high
ambient temperature enclosures. Best results if installed and maintained according to the following recommendations.
INSTALLATION
CAUTION: Unit will fall if not installed properly. Follow installation instructions.
The floodlight is provided with a trunnion bracket which can be mounted directly on flat surfaces or building fronts. The
trunnion bracket has a clearance hole for a ¾ inch bolt used for attachment for such mountings. The ½ inch holes on
either side permit additional anchoring, where required. Tighten side trunnion bolts to 18-22 foot pounds.
AIMING
Slightly loosen bolts (two on side of trunnion),tilt luminaire to desired position and retighten bolts.
LAMPS
Use only lamps specified on nameplate. Bulb not included with fixture. Observe lamp manufacturer’s recommendations
and restrictions on lamp operation, particularly ballast type, burning position, etc.
WIRING
Make all electrical connections in accordance with the National Electrical Code and any applicable local code
requirements.
Verify that the supply voltage is correct by comparing it to the nameplate. Follow specific instruction on page 2.
Three conductor No. 14 cable (with 90°C minimum insulation) is recommended for making electrical connections to the
HALPRM-PS-1000WMH.
Wiring is accomplished through the wiring box provided on the fixture. The box is provided with a size ¾ inch NPT
threaded conduit opening. Wiring methods must comply with NFPA 70 (The National Electrical Code) Article 501 for
Class 1, Division 2 Hazardous (Classified) Locations.
To get inside the unit, open the door, loosen the (2) screws holding the reflector and remove the reflector. Verify the
correct supply voltage and lamp wattage on fixture nameplate.

HALPRM-PS-1000WMH
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
IF SINGLE VOLTAGE
All single voltage ballasts are pre-wired such that user need only connect the supply connectors.
MULTIVOLT (120/208/240/277V)
Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the ballast terminal
nameplate.
WIRING OUTDOOR SALT WATER MARINE
Wiring is accomplished through the wiring box on the bottom of the fixture. When wiring is complete, tighten weatherproof
fitting on box around cable.
MAINTENANCE
CAUTION: Risk of Burn. Disconnect power to the light and allow the unit to cool down before performing maintenance.
The ALGLAS finish on the reflector and the door glass may be cleaned with any suitable nonabrasive glass cleaning
solution, soap, or detergent and rinsed with clean water.
Perform visual,mechanical and electrical inspections on a regular basis. We recommend routine checks to be made on a
yearly basis. Frequency of use and environment shoulddetermine this. It is recommendedto follow anElectrical
Preventive Maintenance Program as described in NFPA 70B: Recommendedpracticefor Electrical Equipment.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use. Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPP-20A-25P is designed to provide years of reliable performance. Should the need for replacement parts arise,
please contact Larson Electronics.