Larson Electronics WAL-HL-2000W-240V User manual

WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 7
Outdoor Rated 2000 Watt Heat Lamp
240V AC - IP66 - Wall or Parasol Mount
Instruction Manual
Thank you for your purchase of the Larson Electronics WAL-HL-2000W-240V.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE WAL-HL-2000W-240V MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.

WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 7
1) ELECTRICAL SAFETY
WARNING: It is the responsibility of the owner and the operator to read, understand and comply with the following:
Check all electrical products before use to ensure that they are safe. Inspect power cables, plugs, sockets, and any
other connectors for wear or damage. Ensure that the risk of electric shock is minimized by the installation of
appropriate safety devices. A Residual Current Circuit Breaker
(RCCB) should be incorporated in the main distribution board. If in any doubt, consult a qualified electrician. Please
read and understand the following instructions concerning electrical safety:
TheHealth & Safety at Works Act 1974 makes owners of electrical appliances responsible for the safe
condition of those appliances and the safety of the appliance operators. If in any doubt about electrical safety,
contact a qualified electrician.
Ensure that the insulation of all the cables on the unit are not undamaged and safe, before connecting it to the
power supply.
Ensure that the cables are always protected against short circuit and overload.
Regularly inspect the power supply cables and plugs, etc. for wear or damage and check all connections to
ensure that none are loose.
Important: Ensure that the voltage marked on the heat lamp matches the power supply to be used and that a
correctly rated fuse is fitted.
DO NOT pull or carry the heat lamp by the power cable.
DO NOT use worn or damaged cables, plugs, or connectors. Immediately have any faulty item repaired or
replaced by a qualified electrician.
Installation should always be carried out by a qualified electrician or a competent person in accordance with
current electrical regulations.
The unit should be protected by a suitably rated isolator and fused or type 3 (also known as type
C) mcb. An inrush current (initial current through the filament) can be expected at switch on. This current can
be as high as 12 times the normal operating current, lasting around 20 milliseconds. This effect can also vary
depending on temperature. In extreme cases, a type D breaker may be required.
This heat lamp is IP66 rated and is suitable for outdoor use. To maintain the protection rating all connections
to the main must be done with a minimum of IP66 equipment.
The main lead is made from high temperature cable, not a standard PVC cable, and should not be replaced
without consulting a suitable qualified electrician.
Ensure that the mounting bracket is adequately earthed.
Use of an extension cord is not recommended.
2) GENERAL SAFETY
Remove all packaging. Check the package and heat lamp for visible damage or tampering.
Familiarize yourself with the applications and limitations of the heater.
Ensure the heater is in good order and condition both physically and electrically before use. If in any doubt, do
not use the unit and contact an electrician.

WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 3of 7
Only use recommended attachments and parts. Using unauthorized parts may be dangerous and will void the
warranty.
Check that the lamp guard is in place, undamaged, and firmly attached.
Keep tools and other items away from the heat lamp when in use.
Keep the work area clean and clear of unnecessary items.
Keep children and unauthorized persons away from the heat lamp.
Disconnect from main and allow cooling before moving or attempting any cleaning or maintenance.
DO NOT use in areas where hazardous vapors may be present.
DO NOT subject the heat lamp to prolonged exposure to water. The product is IP66 rated.
DO NOT place the heat lamp below the power outlet.
DO NOT touch the heat lamp, even when cold.
DO NOT disassemble the unit for any reason. It must be checked by qualified personnel only.
DO NOT use this heat lamp to perform a task for which it has not been designed.
WARNING: If a fuse blows, ensure it is replaced with an identical fuse type and rating.
If removed from its mounting position when not in use, store the heater carefully in a safe, dry, child proof
location.
WARNING: Never touch the lamp directly with your fingers. Use a soft cloth; otherwise the tube may get
damaged.
WARNING: This heat lamp is not equipped with a device to control the room temperature.
WARNING: Ensure that the unit is at least 3 feet from any object and there is no possibility of inflammable
materials coming into contact.
3) INTRODUCTION & SPECIFICATIONS
This heat lamp produces a totally dry heat, no condensation, no gas, no fumes and no smell. It reaches maximum
heat output within seconds of being turned on and has a highly polished aluminum reflector for maximum heat
efficiency. It adjusts horizontally through 90° while mounted and is ideal for industrial or domestic applications.
Model WAL-HL-1500W WAL-HL-2000W
Power 1500W 2000W
Input Supply 230V 50Hz 6.5A 230V 50Hz 8.7A
Dimensions (W x H x D) 480 x 125 x 125mm 480 x 125 x 125mm
Mounting Bracket Stand Off 45mm 45mm
Minimum Mounting Height 1.8m 1.8m
4) MOUNTING INSTALLATION
WALL MOUNTING
IMPORTANT - The following points should be noted:
The heat lamp should always have a minimum clearance of 2’from a ceiling and at least 3’ from any object.
Ensure that the mounting surface is capable of supporting the weight of the heat lamp.
The heat lamp should be mounted horizontally where possible or at a maximum angle of 35°
The mounting bracket must be sufficiently earthed. Remove the wall mounting bracket from the heater by
removing the two bolts from either end of the bracket.

WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 4of 7
Before drilling, ensure that there are no wires or water pipes in the area where the lamp is to be placed.
Use the bracket as a template. Fix the bracket to the wall by means of the three holes and appropriate fittings (not
supplied). Refit the lamp back onto the bracket and secure with the two bolts. Adjust the angle of the unit to direct
heat where required, between 45° and 90°.
PARASOL MOUNTING
Ensure the heater is at least 2’away from the canvas or material of the parasol. Bolt the supplied parasol clamp to
the wall mounting bracket on the back of the heater. Bolt to one of the outer bracket holes so the parasol bracket
will be central to the main bracket. Elevate the heat lamp up to the correct height and tighten the parasol clamp
around the parasol arm and secure in place. IMPORTANT: The main cable must not touch or lie on the back of the
heater. The mounting bracket must be sufficiently earthed.
5) ELECTRICAL CONNECTION
Please make sure you have read the Safety instructions and you are a suitably qualified electrician before
continuing.
Connecting to a Plug (US/Canada)
a) Connect the Green/Yellow earth wire to the earth terminal “E”.
b) Connect the Black live (hot) wire to the live terminal “L”.
c) Connect the White neutral wire to the neutral terminal “N”.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the
cable outer insulation extends beyond the cable restraint and that the restraint is tight.
Connecting to a Switched Fused Spur / Isolator
a) Connect the Green/Yellow earth wire to the earth connection.
b) Connect the Black live (hot) wire to the live connection.
c) Connect the White neutral wire to the neutral connection.
d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the
cable outer insulation extends beyond the cable restraints and that the restraint is tight.
6) OPERATION
NOTE: The infrared lamp in this unit is fragile. It is important that it’s not subjected to any unnecessary shocks or
vibration and is not moved when in use. Wait until the unit has cooled down before moving.
WARNING: Ensure you have read, understand, and apply the safety instructions in Section 1 before using the heat lamp.

WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 5of 7
Ensure the unit is at least 3’from any object. The heater can be tilted from 45° to 90°. Set it to the
required angle before switching the unit ON. Adjust the heater angle by loosening the two bolts on the
wall mounting bracket. Tighten the bolts when the desired angle is reached.
Ensure that the main supply is adequately protected and that the mounting bracket is earthed, then
switch the unit ON.
Make sure the heat lamp is disconnected from the main supply before any cleaning is attempted.
Allow the heat lamp to cool completely.
When the heater is no longer required, switch the unit off and unplug it.
Clean the exterior with a soft damp cloth.
To replace the lamp, contact an authorized dealer.
The main lead is made from high temperature cable, not a standard PVC cable and should not be
replaced without consulting a suitably qualified electrician.
7) MAINTENANCE
NOTE: Before examining or carrying out any maintenance, ensure the lamp has cooled down and is disconnected
from the main supply.
Theheat lamp contains no moving parts, so very little maintenance is required. Ensure that there is no excessive
build-up of dust/dirt on the reflectors or emitters as this can cause overheating and premature emitter failure.
To clean the unit, turn off and disconnect from the main supply. Allow to cool, then wipe with a damp cloth.
8) LAMP REPLACEMENT
NOTE: Before examining or carrying out any maintenance, ensure the heater has cooled down and is disconnected
from the main supply.
The lamp used in the fitting is robust and if knocks and shock vibrations are avoided, it will last for around 5,000
hours.
To Replace the Lamp
a) Disconnect the heat lamp from the power supply by unplugging from the main socket and wait until the
body has cooled down.
b) Remove both end caps by undoing the 2 socket head screws at each end.
c) Remove the guard and lift out the end reflectors.
d) Unclip the lamp from the spring clips at each end, allowing the lamp to move forward clear of the back
reflector.
e) Unclip the reflector from the heater casing.
f) Disconnect the lamp wires from the terminals located in the electrical box and reconnect them into the
terminals. Ensure that the terminals are tightened correctly to make a good electrical connection.
g) Re-assemble making sure all the parts are replaced and the guard is in position.
WARNING: Failure to reassemble all the parts and use the guard will invalidate any remaining guarantee and
may make the unit dangerous.

WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 6of 7

1
° 
 



 u


3
° 
he
µ�cemng



r ,- 



° 

J

r


�

.. 
  


WAL-HL-2000W-240V
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 7 of 7
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The WAL-HL-2000W-240V is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.