Larson Electronics EPL-PM-1X30LED-6XMB-10 User manual

EPL-PM-1X30LED-6XMB-10
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1 of 3
50W Magnetic Mount Explosion Proof LED Light
(4) 100lb Magnets - 100' SOOW Cord w/ EXP Plug
Instruction Manual
Thank you for your purchase of the Larson Electronics EPL-PM-1X30LED-6XMB-10 Magnetic LED Light.
WARNING
TO AVOID THE RISK OF FIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL
APPLICABLE ELECTRICAL CODES.
TO AVOID ELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. WHEN EXTENSION
CORD IS CONNECTED TO A POWER SOURCE IN HAZARDOUS AREA, PLUG AND MATCHING RECEPTACLE
MUST BE SUITABLE FOR HAZARDOUS LOCATION INVOLVED. IMPROPER USE OF THIS DEVICE, ASSOCIATED
PLUG, RECEPTACLE, AND CORD CAN LEAD TO SERIOUS INJURIES OR DEATH TO PERSONNEL.
PERIODIC INSPECTION OF THE RECEPTACLE AND CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY
ARE FOUND, THE CORD MUST BE REPLACED BEFORE RESUMING USE OF THE UNIT.
ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION AND MAINTENANCE.
INSTALLATION AND MAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND COMPETENT
ELECTRICIAN.
IF ANY PARTS OF THE RECEPTACLE OR PLUG APPEAR TO BE MISSING, BROKEN, OR SHOW SIGNS OR
DAMAGE, DISCONTINUE USE IMMEDIATELY. REPLACE WITH THE PROPER REPLACEMENT PART(S) BEFORE
CONTINUING SERVICE.
Mounting
The explosion proof LED light is mounted on a pedestal base with four, 100lb magnets, providing a combined 400lbs of
magnetic gripping force. The entire unit is fabricated from cast aluminum. This unit has a built-in carrying handle and
the light head can be adjusted through 135° of vertical movement. Simply place this unit in the desired location on a flat,
magnetic surface that is capable of supporting the load of the fixture. Take care not to slide the unit when removing,
especially on a painted surface, as this may cause scratches.
PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE USE.
ELECTROMAGNETIC FIELDS IN CLOSE PROXIMITY TO HEART PACEMAKER COULD CAUSE
PACEMAKER INTERFERENCE OR PACEMAKER FAILURE.
KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING AS INJURY COULD OCCUR.

EPL-PM-1X30LED-6XMB-10
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2 of 3
Warning: Check product label for correct voltage!
Position device near work area for operation. Run cable to nearby power source. Insert and twist-lock explosion-
proof plug into a compatible receptacle outputting correct voltage within the hazardous environment. See plug operation
below.
PLUG OPERATION
Electrical connection between plug and compatible receptacle is accomplished after plug fully inserts into receptacle
and is rotated clockwise.
1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug
straight all the way into receptacle until it cannot go further.
2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also
mechanically locks plug into receptacle so it cannot be pulled out.
3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
5. Fixture is field serviceable by a licensed electrician, and all major parts are available from Larson
Electronics.
Light Head Adjustment
Once the light is mounted in the desired location, the angle of the light head
itself can be adjusted to achieve maximum lighting efficacy. Simply loosen the
two T-handle adjustment screws on either side of the light, tilt the light head into
the desired position, and re-tighten the T-handle screws to hold it in place.
Power
T-handle
Adjustment
Screw
Once the light is mounted in the desired position, you are now ready to power on the light. Be sure explosion proof plug is
being mated with compatible explosion proof receptacle within the hazardous area, and follow all applicable local and
national electrical codes.

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 3 of 3
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use. Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPL-PM-1X30LED-6XMB-10 is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
This explosion proof LED light fixture is field serviceable. All major internal components can be purchased from Larson
Electronics and installed by a licensed electrician with basic tools. With most explosion proof fixtures, the fixture must be
returned to the manufacturer for repair work, which presents downtime and long turn around times for repair work. Larson
Electronics addresses this issue with the EPL-PM-1X30LED-6XMB-10 series with field serviceability, allowing operators
to perform service work without having to return the fixture to the manufacturer in the event of damage or failure.
EPL-PM-1X30LED-6XMB-10
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.