Larson Electronics Golight Stryker GL-3049-P Manual

Golight Stryker Remote Controlled Spotlight
Adjustable Double Ball / Socket Mount Base
INSTRUCTION GUIDE
Part# GL-3049-P
Congratulations
You are now the owner of one of the finest remote control searchlights available today. Thank you for
letting Larson Electronics assist you in your lighting application needs. We're proud of our products and
the technology that we've developed to ensure our customers the most durable, versatile and powerful
searchlights in the lighting industry.
Please read these instructions before using your new Remote Control Spotlight from Larson Electronics.

The GL-3049-P Light is a 2-Speed Searchlight with
Directional Flexibility which gives the operator a full
370° horizontal rotation and a 135° vertical tilt with
fingertip control. The Stryker Light provides superior
light penetration with the new Cr5 PentaBeam II
technology.
GL-3049-P Light Wireless - Permanent Mount:
Searchlight
Remote Control (Per Model Number) 2 - 23A 12V
Batteries Permanent Mounting Gasket Permanent
Mounting Plate Mounting Screws
Rockguard
GL-3049-P Light Wireless - Magnetic Mount:
Searchlight
Wireless Hand Held Remote Control
2 - 23A 12V Batteries
Rockguard
MOUNTING INSTRUCTIONS
Light Unit/Magnetic Mount
Select the best location for the magnetic mount
Stryker. Make sure the metal area under the
magnetic base is flat and clean to ensure a strong
bond. Route the power cord and connect to power
outlet. The magnetic mount should be removed from
vehicle exterior when traveling at excessive speeds
and in strong wind conditions.
The ball and socket style mounting base provides
flexible adjustment while mounted. The Golight is
permanently mounted via four holes in the base plate
or magnetically mounted with a 200 pound grip
magnetic base depending on model purchase.
To adjust ball socket, loosen
the hand screw on the side of
mount and move arm around
until it is in the desired
location. Tighten hand screw
to lock mount in place.
When removing from painted surfaces, pull
magnet straight up and away from the surface to
prevent scratches. Do not drag.
Wireless Dash Control
If you have a wireless dash control, please note that
it is vital for this to be attached to a flat / smooth
surface with the 4 mounting screws included. The
arrow under the rubber cover should point up.
BATTERY INSTALLATION AND REMOVAL FOR
TRANSMITTER
Remove battery cover: for wireless hand-held
transmitter, remove phillips head screw to remove
cover. For wireless dash mount remote, simply
remove the exterior rubber cover. With battery
compartment now exposed, insert batteries
according to the correct polarity or gently remove
batteries by grabbing the positive end and lifting up.
PROGRAMMABLE REMOTE INSTRUCTIONS
The GL-3049-P Light is controlled with a
programmable remote with 2187 different channels.
This feature allows you the freedom to change the
channel selection, and the receiver re- learns the
new selection. This light has been pre-programmed
at the factory, and it is not necessary to re-program
the transmitter, unless you experience outside
interference. To program transmitter:
1. IMPORTANT: Disconnect power.
2. Remove battery cover from remote control.
3. Set the 7 dip switches to a selection of your
choice. There are 3 positions on each; positive,
negative and neutral. Use a small screwdriver
and select a position for each dip switch. *Please
note that the orientation of the +/- switch
positions may vary among different models of
wireless remote controls.
4. Insert both GP 23A 12V batteries. Be sure
batteries have adequate charge.
5. Replace battery cover.
a. Depress the on/off button and hold it
down. Red LED will light.
b. While holding the on/off button down,
reinstall the power (replace fuse or
connect vehicle battery).
c. Keep on/off button depressed for 5-6
seconds, and then release. The light
should now be programmed.
OPERATION OF GL-3049-P
1.Using the remote control, turn on the light by
moving the on/off switch.
2.With the joystick on the dash control, rotate your
light to the desired location.
3.The speed of the light rotation can be controlled
by depressing the fast/slow button one time and
by depressing it again to restore the original
speed.
4.The spotlight should not be turned on when the
snap on lens cover (rockguard) is attached. The

hard wired dash control will be backlit when the
bulb is illuminated.
USAGE:
» This light is intended for off-road and utility use only
» This light is intended to be mounted outside the
vehicle while in use
» This light may only be disassembled and repaired
by an authorized representative
MISUSE:
» This light is not approved for road or highway use
» This light is not approved for underwater use
» This light is not approved for inverted mounting
» This light is not approved for use inside a vehicle or
enclosure and power should be disconnected prior to
placing the light in such circumstance
» This light may be damaged if operated in icing
conditions
» This light may only be dismantled by an authorized
Larson Electronics representative.
» Any violation of the above referenced misuses
will be considered grounds for warranty refusal
IMPORTANT SAFETY INFORMATION
This symbol is to alert you to important operating
or servicing instructions that appear in your
instructions.
Always follow basic safety
precautions when using this product to reduce the
risk of injury, fire or electric shock.
This light is for off road and utility use only. It
is not designed for road use as a driving light.
The GL-3049-P complies with Part. 15.105 of the
FCC Rules. This equipment has been tested and
found to comply with the limits for a Class B
digital device. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment
and receiver.
•Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced
radio/TV technician for help.
FCC RULE Part. 15.21 - Changes or
modifications made by the user not expressly
approved by Larson Electronics, LLC. for
compliance could void the user’s authority to
operate the equipment.
PARTS / ACCESSORIES
GL-3049-P parts and accessories may be
purchased through Larson Electronics.
Should further information not covered by these
instructions be required, please contact Larson
Electronics at 1-800-369-6671 or
[e-mail] for further assistance.
Please visit LarsonElectronics.com for Warranty
and Return information.
LARSON ELECTRONICS, LLC
9419 E US-HWY 175
KEMP, TX 75143
800.369.6671 | 903.498.3363
www.larsonelectronics.com
[e-mail]