Larson Electronics Golight Stryker GL-30064ST User manual

GL-30064ST
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
LED Golight Stryker GL-30064ST Wireless Remote Control Spotlight w/
Handheld Remote - Permanent Mount
INSTRUCTION MANUAL
Thank you for your purchase of the Larson Electronics GL-30064ST.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE GL-30064ST MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND
ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
The Larson Electronics GL-30064ST Golight LED Stryker offers powerful illumination and wireless remote functionality in rugged work
sites. This 40-watt light features 10 high flux LEDs and a P-Vex lens. During use, the unit provides up to 544,000 candela output that is
capable of illuminating targets up to 4,839 feet away. Operators can mount the UV and saltwater resistant LED light using an included
stainless steel bracket.
LowVoltage DC
Connect power to power supply outputting low voltage between 9-42Volts DC.
This variable voltage allows greater versatility without affecting light output. Ensure
deutsch connectors are properly connected (If applicable)
REMOTE OPERATION
Remote control functions include on/off, home and 4 buttons which control up, down, left and right movement. The light will
continue movement as long as the buttons are pressed. Releasing the buttons stops movement and holds the Golight in
position. A fast and slow mode button (turtle/hare) controls the speed of the motor while the pan and tilt function buttons are
depressed. Holding the button for 12 seconds in fast mode results in a full 370 degree rotation, and 8 seconds for full tilt.
Slow mode is used for pinpoint accuracy at distance and is approximately 35 seconds for full rotation and 20 seconds for
one full range of tilt. Simultaneous pan + tilt is possible. An included on-command return function automatically brings the
unit to 0° home.
POWER
This light operates with 12 volts DC and draws 3.7 amps, making it ideal for vehicles, boats, ATVs, and similar sources of
12 volt direct current.
MOUNTING
The light is permanently mounted using an included stainless steel mounting bracket.

GL-30064ST
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
MOUNTING INSTALLATION
Determine the location for the light on your vehicle or boat. Remove the mounting plate from the light. Center the
mounting plate with the vise screw on the mounting plate to the back. Mark the hole locations for the three mounting
screws and drill a pilot hole for each with a 1/8 inch bit. Fasten the stainless steel mounting plate with the 3 #10 – 16x ¾
type AB cross recessed pan head tapping screws. Drill a ¼” hole (wireless) or a 5/8” hole (hardwired) in the center of the
mounting plate opening to accommodate the power wire or wiring harness and connector. Attach the connector that is
affixed to the underside of the light to the corresponding connector on the wiring harness (hard-wired). Position the
connection point beneath the mounting surface, and apply silicone sealant around wire to seal the drilled opening. Wet
the mounting surface with a small amount of water or lubricant for easier installation, then place the light over the
mounting plate by sliding the front of the light over the front of the mounting plate, first pull the light backwards, then seat
the back of the light on the mounting plate. Displace the back of the gasket and install the vise screw (provided). Tighten
the vise screw using a Philips head screwdriver. Replace the gasket
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The GL-30064ST is designed to provide years of reliable performance. Should the need for replacement parts arise,
please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.