Larson Electronics LEDWP-600E-OS Manual

LEDWP-600E-OS
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 3
LEDWP-600E-OS Instruction Guide
60 Watt LowProfile LED Wall Pack Light w/ Motion Sensor
Thank you for your purchase of the Larson Electronics LEDWP-600E-OS Wall Pack Light. Please follow the
steps below in order toinstall, operate and maintain this product.
MOUNTING
The LED wall pack includes all necessary hardware for installing the mounting bracket, cord grip, and
(optional) glare shield. Follow the guideline below to properly assemble and install the unit.
The wall pack light includes the LED light, trunnion mount, (optional) glare shield, and hardware for installing
the center cord grip. Some models may omit hardware depending on selected options.
Ambient Temperature Range: -25°C to +60°
1. Begin by choosing a location to install the fixture. This LED wall pack is IP68 waterproof, vapor proof,
and built to resist the damaging effects of an outdoor environment. This fixture should not be used in areas
with no ventilation or extreme ambient temperatures.
2. Affix the mount to your chosen surface. There are 3 predrilled holes on the trunnion bracket. 2 for
mounting and 1 for the cord grip. These can be used any way suitable for the location. Plan a way for
wiring to connect such as using a separate junction box and utilize the cord grip where necessary.
3. Attach lamp.The trunnion mount can be attached to the lamp in two locations, the lower area or middle
area on the back of the wall pack. Use the included ( 2 screws ❶) and ( 2 lock washers ❷) for
attaching the mount as shown in the diagram on page 2. The fixture can be placed in any direction.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz
except those factory ordered with low voltage 11V to 25V AC/DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light
fixture wires as shown in the diagram

Secure each pair with a wire nut according to the
diagram. Utilize a junction box or similar device and
take precautionary steps for weatherproofing all
connections if installed in a location where water may
come in contact with the unit. Ensure the unit is
properly grounded.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDWP-600E-OS MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE
AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 3
ASSEMBLY
Use the table below for assembling the hardware including the (optional) glare shield.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good
practice to routinely clean and check the fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture
is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the
LED’s.
TROUBLESHOOTING
Refer to the guide below or contact the manufacturer if the fixture does not function properly.
Is the correct line voltage being supplied to the fixture?
Is the fixture properly grounded?
Make sure installed power switches, photocells, etc. are functioning properly.
These instructions may not cover all details or variations of this product for your equipment or installation
requirements. Should further information not covered by these instructions be required, please contact Larson
Electronics at 1-800-369-6671 for further assistance.
CORD GRIP
MOUNT SCREW
ASSEMBLED UNIT w/Glare Shield
LEDWP-600E-OS

LEDWP-600E-OS
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
3of 3
LEDWP-600E-OS Motion & Night / Day Sensor Information
The LEDWP-600E-OS Wall Pack Light is equipped with an adjustable motion & day/night sensor that
automatically turns the light on when motion is detected or certain ambient light conditions are met.
Mounting
The motion & day/night sensor features through hole mounting.
Wiring
The motion & day/night sensor is equipped with pigtail wiring for completing wiring connections. Please refer
to the wiring diagram for the motion sensor for connection specifics.
Detection Range
The motion & day/night sensor on this unit has a motion detection range of approximately 40 feet when
mounted at a height of between 5 and 8 feet.
Adjustability
The motion & day/night sensor on this unit has adjustable day/night settings and time settings. It can be
adjusted for both light levels required to turn it on and off as well as for the amount of time it remains
turned on when motion is detected. Adjustments are made via dials found on the bottom of the motion
& day/night sensor.