Laufen Verbana User manual

This instruction must be given to the user.
Guarantee/Liability only when assembled by an approved specialist in accordance with the instructions and local regulations.
Bathtub
EN
Art.-No. 2.2294.2.000.000.1
Verbana
Sentec

EN
Dimensions (mm)
1735
800
1500
615
1800
600
550
1490
70
Parts list, tub assembly installation instructions
Instructions for use
These instructions for use must be
carefully read before installation.
Check on content of delivery and condition of the
components: Check delivery after receipt for
completeness and possibly damage (see parts list).
Inform the dealer immediately when damage is
apparent. We are not liable for damage arising during
or after installation/fitting.
Check door width before starting work: Does the
product fit through the door of the room, in which it
will be installed? Required minimum door width:
See dimensions page . 2
Lifting/moving: Only lift/move the tub using the
transport straps supplied - never use the hoses or
installation parts.
Laying circuits: Do not lay any circuits under the bath.
Protection from damage: Use suitable protective
covers to prevent damage to surfaces and blockages
by dirt or dust arising during fitting. Temporarily apply
a protective cover to sensitive components (drain,
nozzles, operating element) before starting installation.
Special precautions: When cleaning the tiles, make
sure that no ammoniac or a similar aggressive
cleaning agent come into contact with the installed
parts.
Water inlet via hydromassage or overflow: The
connection must always be made by a qualified
specialist.
Feed rate:
Maximum 20 litres/min (EN 200)
Overflow rate:
Minimum 36 litres/min (EN 274)
Drainage rate:
Minimum 48 litres/min (EN 274)
Checking that the tub is waterproof: After connec-
ting the water supply and drainage pipes, the tub
must be filled and examined to ensure that it is
waterproof.
Subject to modifications: Laufen reserves the right
to make changes or product modifications without
prior warning.
Installation instructions
Art.-No. 2.2294.2.000.000.1
800
400
800
100
DN40 DN50
Art.-No.: 2.9443.9.000.000.1
Art.-No.: 2.9001.1.000.000.1 Art.-No.: 2.9510.7.004.000.1
2

09
Tub assembly installation instructions
05
04
b)
a)
06
07
EN 3
08
a)
1x
10 11
1x
a) b)
12
03
02
1460
330 330
110
800
400
01
300
400
80
80
100

Laufen Bathrooms AG
Wahlenstrasse 46
CH-4242 Laufen, Switzerland
www.laufen.com
18/02/2021 2.9994.5.000.000.1 BPZ
General Information, Maintenance Instructions
Tub assembly installation instructions
a)
click
b)
14
a)
b)
c)
13 15 a)
24 h
c) b)
silicone
Remove heavy dirt with liquid household cleaner e.g.
dishwash detergents or liquid soap (observe dilution
instructions). Always rinse with plenty of clear water and
buff up with a cloth. Do not use any acidic cleaning
agents or vinegar-based cleaning agents.
Damage
Scratched surfaces should always be treated by
a specialist. Serious damages can be repaired with
the maintenance kit (2.9996.4.###.000.1, 2.9996.7###.1).
Damage resulting from inappropriate treatment by the
user will not be covered by our guarantee.
General instructions for use
Do not exceed 40°C.
Drain the water after each use.
Never leave children unsupervised in the bath
or shower tray.
Care instructions
The surface gathers hardly any dirt and is easy to clean and
care for. For regular cleaning we recommend: A sponge, soft
cloth and some antistatic cleaning agent. Rub down,
if necessary, with a soft cloth. The surface is dirt-repellent.
Avoid using scouring agents or solvents, which may damage
the surface of the shower tray.
Use
Beware! Increased risk of slipping when sur-
face is wet. This is particularly so when using
soap, shampoo, bath oil, etc.