Laufen Palomba User manual

This instruction must be given to the user.
Guarantee/Liability only when assembled by an approved specialist in accordance with the instructions and local regulations.
Bathtub
EN
PALOMBA
Sentec solid surface
Australia
New Zealand
EN
Palomba freestanding Art.-No. 2.4580.2.000.000.A, 1800 x 720/890

EN 2
21 7/16 “
(545 mm)
17 2/16 “
(435 mm)
35 7/16 “
(900 mm)
35 1/16 “
(890 mm)
17 11/16 “
(450 mm)
15 3/16 “
(385 mm)
28 6/16 “
(720 mm)
27 3/16 “
(690 mm)
70 14/16 “
(1800 mm)
47 4/16 “
(1200 mm)
2
15/16
“
(75 mm)
ø2 1/16 “
(ø52 mm)
drain
desagüe
Vidage
782 Ib
(355 kg)
13/16 “ (20 mm)
G 1“
12
EN
General installation instructions
User manual
Protection from damage
Instructions for use
These instructions for use must be
carefully read before installation.
Check on content of delivery and condition of the
components
Check delivery after receipt for completeness and
possibly damage (see parts list on page 3). Inform the
dealer immediately when damage is apparent. We are
not liable for damage arising during or after installation/
fitting.
Check door width before starting work
Does the bath pass trough the door of the room in
which the bath will be installed? Required minimum
door width: See dimensions page 3.
Lifting/moving
The bath must only be lifted/moved using the transport
straps provided - never use the hoses or installation
parts.
Laying circuits
Do not lay any circuits under the bath.
Use suitable protective covers to prevent damage to
surfaces and blockages by dirt or dust arising during
fitting. Cover sensitive components (drain) temporarily
with a protective cover before starting the installation/
fitting.
Special precautions
When cleaning the tiles, make sure that no ammoniac
or a similar aggressive cleaning agent come into
contact with the installed parts.
Water connection through the overflow.
This installation guide does not include details of waste
connection; final decision about installation of waste
connection should be taken by a suitably qualified
person.
Pre-prepare floor slab bath waste with 500 x 450 x 90 mm
floor chase and 40 mm trap with 40 mm upstand in floor.
EN
Dimensions inches (mm)
Install waste pipe and trap - taking into consideration
the waste position of the bath. Make sure that the
surface where the bathtub will be placed is perfectly
flat, clean, free of any excess humidity and offers
adequate support.
For installation where where access is restricted
eg slab floor, or second story floor, the use of
a Plumbdinger (Product code 9503349) waste
connector is recommended (for installation refer to
Plumbdinger instructions).
After connecting the water supply and drainage
pipes, the tub must be examined to ensure that it is
waterproof.
Changes allowed: Laufen reserves the right to
make changes or modifications on any of its products
without notice.

EN 3
TOP
Usablefor Palomba Freestanding:
-Art. No 2.4580.2.000.000.U
10cm 10cm
10cm
TemplateArt. No 2.9996.3.000.000.U
EditionV1

Wasteoutlet
264 Ib
120 kg
TOP
Usable for Palomba Freestanding:
- Art. No 2.4580.2.000.000.U
10cm 10cm
10cm
Template Art. No 2.9996.3.000.000.U
EditionV1

Waste outlet
:RRGVXSSRUWWREHXVHGIRULQVWDOODWLRQ
:RRGVXSSRUWWREHXVHGIRULQVWDOODWLRQ
a)
a)
d)
b)
c)
b)
b)
b)
c)
a) b)
0302
3 2/16“
(80)
EN
Parts list
TOP
Usable for Palomba Freestanding:
- Art. No 2.4580.2.000.000.U
10cm 10cm10cm
Template Art. No 2.9996.3.000.000.U
EditionV1

Waste outlet
:RRGVXSSRUWWREHXVHGIRULQVWDOODWLRQ
:RRGVXSSRUWWREHXVHGIRULQVWDOODWLRQ
Art.-No.: 2.9996.3.000.000.A
Art.-No.: 2.9511.7.004.000.1
01
EN
Tub assembly installation instructions

EN 4
TOP
Usablefor Palomba Freestanding:
-Art. No 2.4580.2.000.000.U
10cm 10cm10cm
TemplateArt. No 2.9996.3.000.000.U
EditionV1
Wasteoutlet
a)
40 mm
PVC
DWV
b)
Pre-Prepare oor
G 1 “
1
2
B-05
04
B-06
a)
b)
G 1“
12
TOP
Usablefor Palomba Freestanding:
-Art. No 2.4580.2.000.000.U
10cm 10cm10cm
TemplateArt. No 2.9996.3.000.000.U
EditionV1

Wasteoutlet
a)
A-05 A-06
A: Timber floor with clear
access under bath
B: Concrete floor with no
access below floor
(floor chase)
EN
Tub assembly installation instructions
The following red marked installation components
are not included in delivery.
They are shown as examples to identify a proper
installation.

EN 5
a) b)
b)
a)
24 h
c)
c)
13
MAX. MAX.
09
a)
b)
1x
12
07 08
10 11
1x
EN
Tub assembly installation instructions

EN 6
EN
General Information, Maintenance Instructions
General comments on operation and use
For your safety bathtub temperature should not
exceed 40°C.
Let water out after each bath. Never leave children in
the tub unsupervised.
Use
Beware!
Increased risk of slipping when surface is wet. This is
particularly so when using soap, shampoo, bath oil,
etc.
Maintenance instructions
The surface is simple to clean and maintain. The
smooth surface hardly collects dirt. Regular care:
Sponge, soft cloth, somewhat antistatic cleaning
agent. The tub will thus retain its gloss and reject dirt.
To clean your massage tub, please use a soft sponge,
liquid soap and water. Rub dry with a dry cloth.
Avoid the use of abrasives or solvents which damage
the surface of the tub.
After long contact periods, several substances like ink,
cosmetics and dyes may leave colouring stains. Lit
cigarettes can leave burning rings.
These stains and spots as well as scratches or other
small damages can be removed following the recom-
modations below:
Remove heavy dirt with liquid household cleaner e.g.
dishwash detergents or liquid soap (observe dilution
instructions).
Remove lime marks with a decalcifier. Always rinse
with plenty of clean water. Give a final polish with a soft
cloth. Use no acid cleaning agents or cleaning vinegar.
Damage
Scratched surfaces should always be treated by a
specialist. Serious damages can be repaired with the
maintenance kit (2.9996.4.000.000.1). Mix filler and
catalyst to a complete dispersion of liquid substance.
Apply the filler on the damaged part and let it cure for
at least 12 hours at minimum 15°C.
Rub the cured filler with a 220 grain glass-paper and
also the part around to eliminate any non-homogene-
ous parts. Clean the surface as described above.
Damage resulting from inappropriate treatment
by the user will not be covered by our guarantee.
EN
Important safety instructions - Instructions pertaining to a risk of fire, electric shock or in jury to persons
Read and follow all instructions!
WARNING: Risk of personal injury. Do not permit
children to use this unit without adult supervision.
WARNING: Risk of personal injury. Do not operate this
unit without the guard over the suction fitting.
WARNING: Risk of hyperthermia and possible drown-
ing. People using medications and/or having adverse
medical history should consult a physician before using
this product.
WARNING: Risk of personal injury. Do not overfill unit
before entering. Entering tub when filled more than 2/3
can cause overflow and slippery conditions. Exercise
caution when entering and exiting.
WARNING: No food or alcoholic beverages. Use of
your bathtub immediately after meals is not recom-
mended. Avoid alcohol consumption before or during
bathing. Alcoholic beverages can cause drowsiness
or hyperthermia resulting in loss of consciousness or
even drowning.
WARNING: Risk of personal injury. Do not use any
electronical devise as shaver, hair dryer, curling iron,
ect. while taking a bath. There is a danger of being
electrocuted.
WARNING: Pregnancy. If you are or think you may
be pregnant, consult your physician before using the
bathtub.
Never drop or insert any object into any opening.
Use this unit only for its intended use as described
in this manual. Do not use any plumbing devices not
recommended by American Standard.
SAVE THESE INSTRUCTIONS

EN 7
EN
Warranty/Liability Provision
2-Year Limited Warranty.
Laufen warrants that the enclosed product shall be
free from manufacturing defects for 2 years from the
date of the initial purchase. This warranty is extended
to the buyer/installer and is non-transferable. If the
product fails during the warranty period due to a de-
fect in manufacturing, the seller, at its option, will repair
or replace the product.
This warranty is only effective if the buyer installs
the product per the enclosed instructions.
This warranty does not cover damage caused by
installation, accident, incorrect handling, improper use,
or normal wear and tear. Continued use or possession
of the goods after expiration of the warranty period
shall be conclusive evidence that the warranty is ful-
filled to the full satisfaction of the buyer. This warranty
is the seller’s sole and exclusive obligation to the buyer.
Obtaining Warranty Service.
Proof of the date of purchase is required to obtain
warranty service. To obtain warranty service, contact
Laufen at www.laufen.com/usa or www. laufen.com/
canada or send the defective product, with a written
explanation, to
Laufen International INC./
Laufen Bathrooms AG
11190 NW 25th Street Suite –100
Miami, Fl 33172
Toll free phone [phone]
The buyer/installer may be charged a reasonable rate
for shipping if the product is repaired or a replacement
is provided.
Disclaimer of Implied Warranties and Other Li-
abilities.
There are no warranties that extend beyond the
description on the face hereof.
The seller undertakes no responsibility for the quality of
the goods except as otherwise provided herein.
This warranty is in lieu of all other express or
implied warranties of merchantability.
The seller assumes no responsibility that the
goods will be fit for any particular purpose for
which you may be buying these goods, except as
otherwise provided herein.
In no event shall the seller be liable for incidental and
consequential damages, lost profits, indemnity, or
attorneys’ fees. If the seller is liable on any claim -
whether based on a statute, contract, warranty, or tort
(such as negligence or products liability) – seller’s total
liability shall be limited to the purchase price of the
product, except where expressly prohibited by law.

Laufen Bathrooms AG
Wahlenstrasse 46
CH-4242 Laufen, Switzerland
www.laufen.com
Controllers name:
Date:
Fabrication number:
29/07/2019 2.9447.6.000.000.A PLU