LCG LCG-072 User manual

1
LED
LED
LED
LED S
S
S
S onic
onic
onic
onic W
W
W
W ave
ave
ave
ave B
B
B
B ar
ar
ar
ar DMX
DMX
DMX
DMX
LCG-072
User
User
User
User Manual
Manual
Manual
Manual
Please
Please
Please
Please read
read
read
read the
the
the
the instructions
instructions
instructions
instructions carefully
carefully
carefully
carefully before
before
before
before use
use
use
use

2
1.
1.
1.
1. SAFETY
SAFETY
SAFETY
SAFETY INSTRUCTIONS:
INSTRUCTIONS:
INSTRUCTIONS:
INSTRUCTIONS:
•Please keep this User Manual for future consultation. If you sell the unit to
another user, be sure that they also receive this instruction booklet.
•Unpack and check carefully there is no transportation damage before using
the fixture.
•Before operating, ensure that the voltage and frequency of power supply
match the power requirements of the fixture.
•It ’ s important to ground the yellow/green conductor to earth in order ot
avoid electric shock.
•Disconnect main power before servicing and maintenance.
•Use safety chain when fixes this fixture. Don ’ t handle the fixture by taking
its head only, but always by taking its base.
•Maximum ambient temperature is TA: 40 ° C. Don ’ t operate it where the
temperature is higher than this.
•The unit is for indoor use only. Use only in a dry location.
•Don ’ t connect the device to any dimmer pack.
•Make sure there are no flammable materials close to the unit while operating,
as it is fire hazard.
•The housing or the lenses must be replaced if they are visibly damaged
•Do not allow children to operate the unit.
•Replace fuse only with the same type.
•Never try to repair the unit by yourself. Repairs carried out by unskilled
people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center.
•Disconnect the mains power if the unit is not used for a long time
•Do not look directly at the Led Light beam while the unit is on
• To prevent or reduce the risk of electrical shock or fire, do not expose the
fixture to rain or moisture.
2.
2.
2.
2. INSTALLATION
INSTALLATION
INSTALLATION
INSTALLATION :
•The unit should be mounted via its screw holes on the bracket. Always
ensure that the unit is firmly fixed to avoid vibration and slipping while
operating. Always ensure that the structure to which you are attaching the
unit is secure and is able to support a weight of 10 times of the unit ’ s weight.
Also always use a safety cable that can hold 12 times of the weight of the unit
when installing the fixture.
•The unit must be fixed by professionals. And it must be fixed at a place
where is out of the touch of people and has no one pass by or under it.

3
3.
3.
3.
3. TECHNICALS
TECHNICALS
TECHNICALS
TECHNICALS SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
SPECIFICATIONS
•LEDs: 12 x TRI-3W LEDs
•Beam angle: 30 °
•LED display for easier operation
•Built-in programs, sound active, auto run, M/S mode, DMX mode, static
colors, IR Remote
•Three sound active modes
•Very good equalizer and chasing effects with music
•DMX-512: 3,4,4,36,37,37 channels selectable
•Power consumption: 45W
•Power input: AC 120V/60Hz
•Size: 109 x 12 x 73 cm
•Weight: 4.2kg.
4.
4.
4.
4. OPERATION
OPERATION
OPERATION
OPERATION
a.
a.
a.
a. Built-in
Built-in
Built-in
Built-in Program
Program
Program
Program
1) Press MODE button, enter the built in program mode menu “ Pr. ××”
2) Press UP or DOWN button, select the effects program Pr.01 ～Pr.35.
3) Press SETUP button, enter setup program run speed menu “ SP ××”
4) Press UP or DOWN button, setup the speed value SP01 ～SP100 （FL ）
5) Press SETUP button, enter setup program run speed flash menu
“ FS ××”
6) Press UP or DOWN button ,setup flash value FS00 ～99
b.
b.
b.
b. Auto
Auto
Auto
Auto Running
Running
Running
Running
1. Press MODE button, enter auto run mode menu “ AUTO ”
2. Press SETUP mode, enter setup auto run mode speed menu “ SP ××”
3. Press UP or DOWN button ,setup speed value SP01 ～SP100 （FL ）
4. Press SETUP button, enter setup auto run mode flash menu “ FS ××”
5. Press UP or DOWN button ,setup flash value FS00 ～99
c.
c.
c.
c. DMX
DMX
DMX
DMX Mode
Mode
Mode
Mode
1. Press MODE Button, enter DMX control run mode menu “ d. ×××”

4
2. Press UP or DOWN button ,setup DMX address value d.001 ～d.512
3. Press SETUP button, enter setup DMX mode menu xxch
4. Press UP or DOWN button ,setup DMX mode 3ch, 4-c1,4c-2, 36 ch,
37c1, 37c2.
CHANNEL
CHANNEL
CHANNEL
CHANNEL numbers
numbers
numbers
numbers 3,
3,
3,
3, 4,
4,
4,
4, 4,
4,
4,
4, 36,
36,
36,
36, 37,37
37,37
37,37
37,37
DMX mode 1 ：3C
CHANNEL VALUE FUNCTION
CH1 0-255 RED
CH2 0-255 GREEN
CH3 0-255 BLUE
DMX mode 2 ：4C-1
CHANNEL VALUE FUNCTION
CH1 0-255 RED
CH2 0-255 GREEN
CH3 0-255 BLUE
CH4 0-255 MASTER DIMMER
DMX mode 3 ：4C-2
CHANNEL VALUE FUNCTION
CH1 0-255 MASTER DIMMER
CH2 0-255 RED
CH3 0-255 GREEN
CH4 0-255 BLUE
DMX mode 4 ：36C
CHANNEL V ALUE FUNCTION SECTION
CH1 0-255 RED
1CH2 0-255 GREEN
CH3 0-255 BLUE
CH4 0-255 RED
2CH5 0-255 GREEN
CH6 0-255 BLUE
CH7 0-255 RED
3CH8 0-255 GREEN
CH9 0-255 BLUE
CH10 0-255 RED
4CH11 0-255 GREEN
CH12 0-255 BLUE
CH13 0-255 RED
5CH14 0-255 GREEN

5
CH15 0-255 BLUE
CH16 0-255 RED
6CH17 0-255 GREEN
CH18 0-255 BLUE
CH19 0-255 RED
7CH20 0-255 GREEN
CH21 0-255 BLUE
CH22 0-255 RED
8CH23 0-255 GREEN
CH24 0-255 BLUE
CH25 0-255 RED
9CH26 0-255 GREEN
CH27 0-255 BLUE
CH28 0-255 RED
10CH29 0-255 GREEN
CH30 0-255 BLUE
CH31 0-255 RED
11CH32 0-255 GREEN
CH33 0-255 BLUE
CH34 0-255 RED
12CH35 0-255 GREEN
CH36 0-255 BLUE
DMX mode 5 ：37C-1
CHANNEL VALUE FUNCTION SECTION
CH1 0-255 RED
1CH2 0-255 GREEN
CH3 0-255 BLUE
CH4 0-255 RED
2CH5 0-255 GREEN
CH6 0-255 BLUE
CH7 0-255 RED
3CH8 0-255 GREEN
CH9 0-255 BLUE
CH10 0-255 RED
4CH11 0-255 GREEN
CH12 0-255 BLUE
CH13 0-255 RED
5CH14 0-255 GREEN
CH15 0-255 BLUE
CH16 0-255 RED

6
6CH17 0-255 GREEN
CH18 0-255 BLUE
CH19 0-255 RED
7CH20 0-255 GREEN
CH21 0-255 BLUE
CH22 0-255 RED
8CH23 0-255 GREEN
CH24 0-255 BLUE
CH25 0-255 RED
9CH26 0-255 GREEN
CH27 0-255 BLUE
CH28 0-255 RED
10CH29 0-255 GREEN
CH30 0-255 BLUE
CH31 0-255 RED
11CH32 0-255 GREEN
CH33 0-255 BLUE
CH34 0-255 RED
12CH35 0-255 GREEN
CH36 0-255 BLUE
CH37 0-255 MASTER DIMMER
DMX mode 6 ：37C-2
CHANNEL VALUE FUNCTION SECTION
CH1 0-255 MASTER DIMMER
CH1 0-255 RED
1CH3 0-255 GREEN
CH4 0-255 BLUE
CH5 0-255 RED
2CH6 0-255 GREEN
CH7 0-255 BLUE
CH8 0-255 RED
3CH9 0-255 GREEN
CH10 0-255 BLUE
CH11 0-255 RED
4CH12 0-255 GREEN
CH13 0-255 BLUE
CH14 0-255 RED
5CH15 0-255 GREEN
CH16 0-255 BLUE

7
CH17 0-255 RED
6CH18 0-255 GREEN
CH19 0-255 BLUE
CH20 0-255 RED
7CH21 0-255 GREEN
CH22 0-255 BLUE
CH23 0-255 RED
8CH24 0-255 GREEN
CH25 0-255 BLUE
CH26 0-255 RED
9CH27 0-255 GREEN
CH28 0-255 BLUE
CH29 0-255 RED
10CH30 0-255 GREEN
CH31 0-255 BLUE
CH32 0-255 RED
11CH33 0-255 GREEN
CH34 0-255 BLUE
CH35 0-255 RED
12CH36 0-255 GREEN
CH37 0-255 BLUE
d.
d.
d.
d. Sound
Sound
Sound
Sound Active
Active
Active
Active
1. Press MODE button, enter sound active mode “ SOUd ”
2. Press SETUP button, to set up sound active mode and sensitivity
menu “ S × . ××”
3. Switch over sound active mode S1. ×× ,S2. ×× ,S3. ×× and the running
direction.
4. Under the mode of S1. ×× ,S2. ×× ,S3. ×× , press UP or DOWN button ,to
set up the sound active sensitivity value S1.00 ～S1.31,S2.00 ～
S2.31,S3.00 ～S3.31 or the running direction when on the mode of
S1. ×× ,S2. ××
e.
e.
e.
e. Slave
Slave
Slave
Slave Mode
Mode
Mode
Mode
1. Press MODE button, enter slave mode “ SLAV ”
2. The running effect program of master light is the same with all slaves
light
f.
f.
f.
f. Static
Static
Static
Static Color
Color
Color
Color
1. Press MODE button, enter static color mode “ COLR ”
2. P ress SETUP button enter the static color, press UP or DOWN

8
button ,you can select 7 static colors (1.-r ；2.-rg ；3.-g ；4.-gb ；5.-b ；
6.-rb ；7.rgb; 8OFF).Press SETUP again, you can press UP or DOWN
adjust the brightness of the static colors .Press SETUP button can
setup the flash “ FSxx ” of the color .Also press UP or DOWN can adjust
the speed of flash of speed.
g.
g.
g.
g. IR
IR
IR
IR Remote
Remote
Remote
Remote
1. Press the “ mode ” , when LED display ：-ir- is on IR remote.
IR remote instruction as below:
A
A
A
A）select
select
select
select the
the
the
the built-in
built-in
built-in
built-in programs
programs
programs
programs by
by
by
by IR
IR
IR
IR remote
remote
remote
remote :
1) Press down the “ AUTO ” , enter the built-in program select mode.
Press down the “ + ” / “ - ” , select the built-in programs Pr.01~Pr.35.
（Note: the button “ AUTO ” function amount to press the button Pr.xx ）.
2) Press down the “ SPEED ” , enter to the state of built-in program running speed,
press down the “ + ” / “ - ” , adjust the built-in program running speed.
3) Press down the “ STROBE ” , enter to strobe state, press down the “ + ” / “ - ” , adjust
the speed rate of built-in programs, and then press the “ STROBE ” , the
stroboscopic stop.
4) Press down the “ FADE ” , the light color will from one change to another one,
press down the “ FADE ” again, the light color will from one hopping to another
one.
B
B
B
B）select
select
select
select the
the
the
the sound
sound
sound
sound active
active
active
active mode
mode
mode
mode by
by
by
by IR
IR
IR
IR remote
remote
remote
remote :
1) Press the “ SOUND ” or “ SENSITIVITY ” , enter sound active mode, press down
the “ + ” / “ - ” , adjust the sensitivity of sound active.
2)select the static color mode by IR remote ：
Press the “ MANUAL ” , enter to select the static color,
Press the numeric buttons “ 0 ” ~ “ 9 ” ，select the fixed monochrome:
0 1 2 3 4 5 6 7 8 9
Whit
e
Red Orang
e
Yello
w
Gree
n
Cyan Blue Purpl
e
Pink Ambe
r
3)press down the “ MANUAL ” , enter select the static color mode, press down the
“R ”（“ G ” or “ B ” ）enter to dimming color mode ，
Press the “ 0 ” - “ 9 ” in turn ，the first input is higher ，the effectively composed
number between 0-100, press the “ % ” again, confirm this number is the
percentage of dimming monochrome.
For example, press the “ MANUAL ” + “ R ” + “ 5 ” + “ 0 ” + “ % ” in turn, set the red LED
brightness is 50% of all the bright.
When adjust one monochrome, press a effectively number, the correspond color
will fading up once, if the setting is ok, the light board will lighting the
monochrome which you setting. If the setting is wrong, the light board will
display the color before you set, can reset the color.
4) press down the “ R ” or “ G ” or “ B ” ，display the user-defined color, press down

9
the “ + ” / “ - ” , adjust the correspond monochrome brightness .
C
C
C
C）Black
Black
Black
Black out
out
out
out and
and
and
and restore
restore
restore
restore factory
factory
factory
factory settings
settings
settings
settings by
by
by
by IR
IR
IR
IR remote.
remote.
remote.
remote.
1) press down the “ BLACK OUT ” , enter black out state; press the “ BLACK OUT ”
once more, recovery the state before
2) In black out state, press down the “ 9 ” + “ 8 ” + “ 7 ” in turn, restore factory
setting.
P.S
P.S
P.S
P.S :
A. If no press the four buttons in 20 seconds, LED display will turn off , now if press
any button, the LED display will recover the state before turn off, then each button
will restore their function.
B. when the system power on, will first display the system version number V1.0,
continue about 2 seconds ，then will operation the user setting working mode.
C. IR remote offer fast operation, more subtle operations please press the button
to satisfy your needs.
5.
5.
5.
5. DMX512
DMX512
DMX512
DMX512 CONNECTIONS:
CONNECTIONS:
CONNECTIONS:
CONNECTIONS:
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
DMX 512 120 OHM 1/4W

10
•1
•
3
•2
1. 1
2.
3
3. 2
INPUT
OUTPUT
COMMON
DMX +
DMX -
Termination reduces signal errors and to avoid signal transmission problems and
interference. It is always advisable to connect a DMX terminal. (resistance 120ohm
1/4W ) between pin2 (DNX-) and pin3 (DMX+) of the last fixture.
1. Connect the fixture together in a “ daisy chain ” by XLR plug cable from the
output of the fixture to the input of the next fixture. The cable cannot be
branched or split to a 2Y ” cable. Inadequate or damaged cables, soldered
joints or corroded connectors can easily distort the signal and shut down the
system.
2. The DMX output and input connectors are pass-through to maintain the DMX
circuit when no power is connected to the fixture.
3. At last fixture, the DMX cable has to be terminated with a terminator to
reduce signal errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-)
and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the
last fixture.
4. Each lighting fixture needs to have an address set to receive the data sent by
the controller. The address number is between 0-511 (usually 0 & 1 are
equal to 1).
5.
5.
5.
5. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+).
Notice:
Notice:
Notice:
Notice:
A. If no any touch the button within 20 seconds, the LED display will be close, if touch
any button at this time, the LED display will be recover the original status. All the
button will be recover the function,
B. This fixture have the excess temperature self defective function. When the
brightness is obvious reduce, please check if the fan work in normal, after clear the
trouble clear, please power supply, the light will be release defend, and work in
normal.
C. Turn on the fixture, it will show the Version No. like V2.0. It will keeps two
seconds, then under the working mode which the user set up.
6
6
6
6.TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING

11
Following are a few common problems that may occur during operating. Here are
some suggestions for easy troubleshooting:
•The
The
The
The fixture
fixture
fixture
fixture does
does
does
does not
not
not
not work,
work,
work,
work, no
no
no
no light
light
light
light &
&
&
& the
the
the
the fan
fan
fan
fan does
does
does
does not
not
not
not work
work
work
work :
3. Check the connection of power and main fuse.
4. Measure the mains voltage on the main connector.
•Not
Not
Not
Not responding
responding
responding
responding to
to
to
to DMX
DMX
DMX
DMX controller
controller
controller
controller :
•DMX LED should be on. If not, check DMX connectors, cables to see if link
properly.
•If the DMX Led is on and no response to the channel, check the address
settings and DMX polarity.
•If you have intermittent DMX SIGNAL problems, check the pins on connectors
or on PCB of the fixture or the previous one.
•Try to use another DMX controller
•Check if the DMX cables run near or run alongside to high voltage cables that
may cause damage or interference to DMX interface sircuit.
•No
No
No
No response
response
response
response to
to
to
to the
the
the
the sound
sound
sound
sound :
1. Make sure the fixture does not receive DMX signal
2. Check microphone to see if it is good by tapping the microphone.
•
•
•
•One
One
One
One of
of
of
of the
the
the
the channels
channels
channels
channels is
is
is
is not
not
not
not working
working
working
working well:
well:
well:
well:
•The stepper motor might be damaged or the cable connected to the PCB is
broken
•The motor ’ s drive IC on the PCB might be out of condition.
7
7
7
7.FIXTURE
FIXTURE
FIXTURE
FIXTURE CLEANING
CLEANING
CLEANING
CLEANING :
The cleaning of internal must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surrounding can cause greater accumulation of dirt on the
fixture ’ s optic.
•Clean with soft cloth using normal glass cleaning fluid.
•Always dry the parts carefully
•
•
•
•Clean the external optics at least every 20 days. Clean the internal
optics at least every 30/60 days.