Leader Light LL STAGE 6-06D User manual

©MMXI - LEADER LIGHT – All right reserved Edition: A - 2011 Additional information on [email protected]
LEADER LIGHT s.r.o.
M.Gorkeho 33
052 01 Spisska Nova Ves
Slovakia
www.leaderlight.eu
USER MANUAL
Page 1 /2
ENVIRONMENTAL PROTECTION
Do not throw away the appliance with the normal household waste at the end of its
life, but hand it in at an offi cial collection point for recycling. By doing this, you help to
preserve the environment.
COMPLIMENTS ON YOUR PURCHASE!
All dimensions are in millimeters
Package includes:
Content:
01 SAFETY INFORMATION
01.1 Risk of eyes damage
01.2 Safety instructions
01.3 Fire protection
02 PRODUCT SPECIFICATION
02.1 Technical specifi cation
02.2 Product description
03 INSTALLATION
03.1 Unpacking
03.2 Physical installation
03.3 Connection
03.4 Control data connection
03.5 DMX channels
04 MAINTENANCE AND SERVICE
01 SAFETY INFORMATION
WARNING!!!
Carefully read before installing, powering or servicing. Nothing to do if
anything misunderstand! Installation can be done only by a qualifi ed
professional in accordance with relevant local codes.
01.1 Risk of eyes damage
Do not look directly into LED lamps.
Do not look into light beam from a distance of less than 40 cm (16 inches)!
-
-
01.2 Safety instructions
Shut down power before installation or maintenance.
Do not modify, alter, or attempt to service the LEADER LIGHT appliance. Doing
so will void the warranty.
Appliance and recommended AC power supply must be installed by a qualifi ed
professional in accordance with relevant local codes. Use only acceptable source
of AC power and frequency that complies with local biulding and electrical codes.
Use only the recommended voltage source.
Appliance always connect to earth (eltech.)!
Do not use or do not connect the products if the power cable, power plug or
fi xtures are any way damaged, wet, or if they are overheating.
Before removing or installing any cover or part of appliance disconnect it from AC
power.
AC power supply must be protected against overvoltage and short circuits.
-
-
-
-
-
-
-
-
01.3 Fire protection
Follow all safety restrictions.
Thermostatic switches or fuses never to bypass.
Device never shield. Around the axis of the fi tting (180°) must be maintained space
for cooling. Minimum distance from the surrounding objects must be 100mm (4 in.).
LEDs never direct cover with fi lters or other materials.
Allowing max. ambient temperature is 40°C (104°F).
Luminaries never use without mounting brackets. The housing never install
directly to the surface.
-
-
-
-
-
-
02 PRODUCT SPECIFICATION
02.1 Technical specifi cation
Power connection: 100-260V AC 50-60Hz In/Out PowerCon
IP: IP20
Control data: DMX 512 In/Out with XLR 5pin
Ambient temp. (Ta): Maximum 40°C
Net weight: 6kg
Installation: Surface mounting
!
LL STAGE 6-06D
LL36 080
02.2 Product description
Indication of control LEDs (LED power- green,LED data - yellow)
LED Indication Status
LED Power blinking - 2Hz O.K. - Device is working correct
LED Data not lit No DMX signal
LED Data blinking - 4Hz O.K. - Correct DMX signal
LED Data fast blinking ERROR - Incorrect digital signal
LED Power &
LED Data alternating blinking function AutoTest
03 INSTALLATION
03.1 Unpacking
Unpack carefully.
This is electronic equipment and should be handled carefully.
Damaged delivered package or if are any mechanical parts broken – it must be
claim immediately by the transport company. Photo pictures as evidence are
valuable for future claim.
-
-
-
03.2 Physical installation
Loading capacity of bearing area has to be at least 10 times the weight of all
device clusters.
Hairbreadth from combustible materials is 0,5m.
Before physical installation insert the optic modul on front of luminary. The optic
installation is easy and fast by 2 screws. (fi gures Nr. 2.1 to 2.2)
-
-
-
03.3 Connection
Respect all SAFETY INFORMATION 01!
Connect the ground (earth) !
It is not necessary to open the fi xture before power supply. Power supply is
solved simple with Neutrik PowerCon connectors.
The fi xture is equipped with auto-switching power supply that automatically
adjusts to any 50-60Hz AC power source from 100-260V.
Cord plug connections:
-
-
-
-
-Symbol Pin Wire Colour Screw (US)
Llive brown yellow or brass
Nneutral blue silver
ground (earth) yellow/green green
!
LL STAGE 6-06D with adjustable bracket- 1pc.
PowerCon type “A“ + “B“- 1pc.
User manual- 1pc.
Additional items needed:
Data cables with XLR 5pin F/M- 1pc.
Controller compatible with DMX- 1pc.
Mounting accessories as necessary-
610
164
98
DMX Out
XLR-5pin
DMX In
XLR-5pin
Power In
PowerCon
Power Out
PowerCon
Power In Data In Power OutData Out
!!
Non-minimum distance and / or non-use the original brackets is at your own risk!
WARNING!!!

©MMXI - LEADER LIGHT – All right reserved Edition: A - 2011 Additional information on [email protected]
Page 2 /2
Camloc 1/4 turn fasteners
Safe mechanical quick release
fastener systems
Locking/unlocking by quarter turn
Hand operated
Service-friendly, time-saving
and cost cutting
Vibration-resistant
-
-
-
-
-
Mechanical mounting of LL STAGE 6-06D
03.4 Control data connection
Control data cable length is specifi ed by Norm IEC929 Annex E4.
It is not necessary to open the fi xture before connecting of DMX512 control sig-
nal. Interconnections are realized by Neutrik XLR 5pin In/Out connectors.
Pin connections:
Pin 1 – ground
Pin 2 – signal negative
Pin 3 – signal positive
-
-
-
03.5 DMX channels
These informations are subject to change, latest data are on: www.leaderlight.eu
04 MAINTENANCE AND SERVICE
Before any maintenance is necessary to carefully read all SAFETY INFORMATION 01!
Damages caused by inadequate cleaning or maintenance are not covered by warranty.
Requires periodic cleaning (dust, dirt ,...)
Procedure for maintenance:
Unplug mains before maintenance and at least 10 minutes cool off.
Appliance do not illegal open or demount.
Clean-up dust only from outer surface. Use vacuum or dumpy duster (warm
water)
Before reinstalling make sure everything is intact and dry– no wet parts!
Service:
Customer service provided by the manufacturer.
-
-
-
-
-
-
-
-
!
Mechanical mounting of frame to the LL STAGE 6-06D
2.1 The screws unlock by hand. Pick out the frame.
Frame installation without tools (Figures Nr. 2.1 to 2.2).
AIMING POSSIBILITY
The fi xture could be aim to wish position with
adjustable bracket.
Mounting on stage is easy using various accessories as seen below (Figures Nr. 1.1 to 1.2). The brackets are connect by Camlocs.
1.1 Serial connection by LL36 300 for creation of continuous line
1.2 Parallel connection by dual bracket LL36 320
LL36 320
LL36 300
LL37 230 LL37 220
2.2 Insert the new frame. Apply the screws by hand.
Functions Dip1-Dip4:
- Dip2=Off, Dip3=Off: Mode1: 6ch(W1,W2,W3,W4,W5,W6) +2ch(Master,Strobo)
- Dip2=Off, Dip3=On: Mode2: 1ch(W1+W2+W3+W4+W5+W6)
+2ch(Master,Strobo)
- Dip2=On, Dip3=Off: Mode3: 2ch(W1+W3+W5, W2+W4+W6) +2ch(Master,Strobo)
- Dip2=On, Dip3=On: Mode4: 3ch(W1+W2, W3+W4, W5+W6) +2ch(Master,Strobo)
- Dip1=on enable add+2ch (Master+Strobo)
- Dip4=Off standard curve-
- Dip4=On ultrasoft curve-
Functions DipBCD:
9xx - AutoTest - gradual fade-over by the Mode
8xx - AutoTest - On W1+W4
7xx - AutoTest - On W2+W5
6xx - AutoTest - On W3+W6
5xx - AutoTest- On all
Order Code Product name Optic
(°)
LL36 080.1 LL STAGE 6-06D W (delivery with LL BEAM FRAME STAGE6) 1°
Accessories
Order Code Product name
LL37 200.1 LL BEAM FRAME STAGE 6-06 (1°)
LL37 220.1 LL FRAME STAGE 6-06 SQ6 MILKY
LL37 230.1 LL FRAME STAGE 6-06 R6 MILKY
LL37 232.1 LL FRAME STAGE 6-06 R6 CLEAR (120°)
LL36 300.1 LL BRACKET STAGE 6 SERIAL
LL36 320.1 LL BRACKET STAGE 6 PARALLEL DUAL (2pcs)
LL36 330.1 LL BRACKET STAGE 6 FIX
LL36 340.1 LL BRACKET STAGE 6 ADJUSTABLE
LL36 345.1 LL BRACKET STAGE 6 MATRIX 6x6
LL90 000 W-DMX MODUL 2,45GHz/5,8GHz DMX/RDM supply with W-DMX antenna
LL36 300
LL36 320 LL36 340
LL36 330
Mounting with LL BRACKET STAGE 6 MATRIX 6x6