Ledj Q Colour LEDJ210 User manual

Order code: LEDJ210
Q Colour
18 x 8W RGBW LEDs
User Manual

www.prolight.co.uk Q Colour User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE-
FULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablemainssupplyvoltageis
between100~240VAC,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.

• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• Thislightingxtureisforprofessionaluseonly-itis
notdesignedfororsuitableforhouseholduse.The
productmustbeinstalledbyaqualiedtechnicianin
accordancewithlocalterritoryregulations.Thesafetyof
theinstallationistheresponsibilityoftheinstaller.The
xturepresentsrisksofsevereinjuryordeathduetore
hazards,electricshockandfalls.
• Warning!RiskGroup2LEDproductaccordingto
EN62471.Donotviewthelightoutputwithoptical
instrumentsoranydevicethatmayconcentratethebeam.
• WARRANTY:Oneyearfromdateofpurchase.

www.prolight.co.uk Q Colour User Manual 3
Product overview & technical specications
Utilisingquad-colourLEDtechnologytheQColouraddsintensecolourtostagesandperformers.
Thexturehasaruggedchassisandprovidesexceptionalquality,coverageandeaseofuse.
Withtheabilitytorunbuilt-inprogramsandperformfullRGBWcolourmixingwithorwithout
DMXcontrolthextureisalsoperfectforarchitecturalworkandinstallation.
•18x8Wquad-colourLEDs(RGBW)
•Beamangle:25°
•400Hzrefreshrate
•DMXchannels:4or6selectable
•Staticcolour,colourmix,colourchange,colourfade,
auto,soundactiveandmaster/slavemodes
•0-100%dimmingandvariablestrobe
•Bracketallowsformultiplerigging
oroorstandingapplications
•3pushbuttonmenuwithLEDdisplay
•IECpowerinput/output
•3-PinXLRinput/output
•Fancooled
Q Colour
Specications Q Colour
Powerconsumption 160W
Powersupply 100~240V,50/60Hz
Fuse T2A250V
Dimensions 222x344x153mm
Weight 4.7kg
Ordercode LEDJ210
222mm
344mm 153mm
0m 1m 2m 3m 4m 5m
25° - Lux 8410 2512 1008
25°
625 384

www.prolight.co.uk Q Colour User Manual 4
Technical specications & operating instructions
01-Fuse:T2A250V
02-IECpowerinput
03-IECpoweroutput
04-Earthpoint
05-3-PinDMXinput
06-3-PinDMXoutput
07-LEDdisplay
08-MODEbutton
09-UPbutton
10-DOWNbutton Inthebox:1 x xture,
1 x power cable &
1 x user manual
www.prolight.co.uk
MODE
DMX INPUT
POWER INPUT/OUTPUT:100-240V~50/60HZ
FUSE: T2A 250V
DMX OUTPUT
DOWN UP
02
09 1008
0301
04
05
07
06
DMX address mode:
Toaccessstaticmodepress“MODE”untilthedisplayshowsAddontheLEDdisplayandusethe
“UP”and“DOWN”buttonstoselecttheDMXaddressrequired001~512.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
DMX channel mode:
Toaccessstaticmodepress“MODE”untilthedisplayshows4CHontheLEDdisplayandusethe
“UP”and“DOWN”buttonstoselectoneofthebetween4or6channelmodes.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.

www.prolight.co.uk Q Colour User Manual 5
Static colour mode:
Toaccessstaticmodepress“MODE”untilthe
displayshowsC01ontheLEDdisplayanduse
the“UP”and“DOWN”buttonstoselectoneofthe
15coloursC01~C15.Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Built-in program mode:
Toaccessthexturesbuilt-inprogramspress“MODE”untilthedisplayshowsP01ontheLEDdisplay
andusethe“UP”and“DOWN”buttonstoselectoneofthe9built-inprogramsP01~P09.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Slave mode:
Pressthe“MODE”buttonontherearoftheunittoshowAddontheLEDdisplayandusethe
“UP”and“DOWN”buttonsuntilthedisplayshows001theunitwillnowruninsequencewith
themasterunit.Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Sound active mode:
Toaccesssoundactivepress“MODE”untilthedisplayshowsS99ontheLEDdisplayandusethe
“UP”and“DOWN”buttonstoselectthesensitivitylevelS00~S99.
(S00-lowsensitivity,S99-highsensitivity).
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
RGB colour mixing:
ToselecttheRGBcolourmixingmode,pressthe“MODE”buttontoshowr--ontheLCDdisplay.
Nowpressusethe“UP” and“DOWN”buttonstoselecttheamoutofredrequired.Pressthe“MODE”
buttonandrepeatforGreen,BlueandWhite(00-99).
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Operating instructions
Channel Value Function
1 000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4 000-255 White(0-100%)
4 channel mode:
Channel Value Function
1 000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4 000-255 White(0-100%)
5 000-255 Masterdimmer(0-100%)
6 000 DMXcontrolCH1-CH5
001-005 15coloursoundactive
006-010 DMXcontrolCH1-CH5
011-255 Strobe(slow-fast)
6 channel mode:
C01-Red C02-Green C03-Blue C04-White(W) C05-Yellow
C06-Purple C07-Cyan C08-White(RGB) C09-Pink C10-LightGreen
C11-LightBlue C12-LightYellow C13-Magenta C14-LightCyan C15-White(RGBW)
P01 7colourchange P04 3colourfade P07 15colourchange
P02 7colourfade P05 7coloursoundactive P08 15colourfade
P03 3colourchange P06 3coloursoundactive P09 15coloursoundactive

www.prolight.co.uk Q Colour User Manual 6
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.

www.prolight.co.uk Q Colour User Manual 7
Terminationreducessignaltransmission
problemsandinterferance.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.

www.prolight.co.uk Q Colour User Manual 8
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.