Ledj HEX Par 9 LEDJ226 User manual

Order code: LEDJ226
HEX Par 9
Exterior Fixture
User Manual

www.prolight.co.uk HEX Par 9 User Manual
2
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
Safety advice
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablevoltageisbetween
100~240V,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• WARRANTY:Oneyearfromdateofpurchase.
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.prolight.co.uk HEX Par 9 User Manual
3
Product overview & technical specications
TheexteriorHEXPar9features9x12Wsix-colourLEDs,
givingsmoothcolourmixingfromrichsaturatedhuestosubtle
pastelshades,controlledviaa4pushbuttonLEDmenuwhichallows
foreasyaccesstothemodesincludingDMX,autoandmaster/slave.
Thisxturecanbeusedforinteriorandexteriorapplications
(IP65rated)makingitsuitableforbotharchitectural
andstagelighting.
•9x12Wsix-colourLEDs(RGBWAUV)
•Beamangle:25°
•4kHzrefreshrate
•DMXchannels:2/3/4/5/6or9selectable
•Autoandmaster/slavemodes
•0-100%dimmingandvariablestrobe
•4pushbuttonmenuwithLEDdisplay
•IPratedpowerin/outsockets
•IPrated3-PinDMXin/outsockets
HEX Par 9 Exterior Fixture
Specications HEX Par 9
Powerconsumption 115W
Powersupply 100~240V,50/60Hz
Dimensions 235x230x205mm
Weight 4.8kg
Ordercode LEDJ280
0m 1m 2m 5m
25° - Lux 10050 2520
25°
446
230mm 205mm
235mm
IP65
01-DMXinputsocket
02-DMXoutputsocket
03-LEDdisplay
04-Powerinsocket
05-Poweroutsocket
06-Modeselectionbutton
07-Downbutton
08-Upbutton
09-Enterbutton
10-Bracket
11-Forsafetywire
Inthebox:
1 x xture, 1 x power cable
& 1 x user manual
MENU UPDOWNENTER
HEX Par 9
01
0706 08 09
03
10
02
04 05
11

www.prolight.co.uk HEX Par 9 User Manual
4
DMX mode:
ToaccesstheDMXmode,pressthe“MODE”buttonuntilthedisplayshowsAddrandpress
the“ENTER”button.Usethe“UP”and“DOWN”buttonstoselectthedesiredDMXaddress
andthenpress“ENTER”toconrmyourselection.
Operating instructions
IMPORTANT! PLEASE NOTE:TheLEDdisplayforthisxturehasamenulockingfunctionwhere
after30secondsofinactivityitwilllock.Tounlockthemenuholdyoumustreturntothemain
menubeforeyoucanthenaccessthesubmenus.
4 channel mode:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
6 channel mode:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
5 000-255 Amber(0-100%)
6 000-255 UV(0-100%)
5 channel mode:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
5 000-255 Amber(0-100%)
3 channel mode 01:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
3 channel mode 02:
Channel Value Function
1000-255 Dimmer(0-100%)
2000-255 Strobe(slowtofast)
3000-004 Nofunction
005-255 Fading&effectmode
2 channel mode:
Channel Value Function
1000-255 Dimmer(0-100%)
2000-255 Colourchange
9 channel mode:
Channel Value Function
1000-255 Dimmer(0-100%)
2000-255 Strobe(slowtofast)
3000-255 Red(0-100%)
4000-255 Green(0-100%)
5 000-255 Blue(0-100%)
6 000-255 White(0-100%)
7000-255 Amber(0-100%)
8 000-255 UV(0-100%)
9000-004 Nofunction
005-255 Fading&effectmode

www.prolight.co.uk HEX Par 9 User Manual
5
Operating instructions
Channel mode:
Toaccessthechannelmode,pressthe“MODE”buttonuntilthedisplayshowsChNdandpress
the“ENTER”button.Usethe“UP”and“DOWN”buttonstoselectthedesiredchannelmodeand
thenpress“ENTER”toconrmyourselection.
MENU
Addr A001 A512
DMX address setting
ENTER UP & DOWN
ENTER
2Ch
4Ch
3Ch1
5Ch
3Ch2
6Ch 9Ch
ChNd
Channel mode
ENTER
UP
UP
UP
UP
UP UP
ENTER
ENTER
ENTER
ENTER ENTER
SLNd
Master mode
Slave mode
ENTER
ENTER
ENTER
UP
NASt
SLAV
teSt
Auto test
ENTER
Led
LED display ON
LED display OFF
ENTER
ENTER
ENTER
UP
o n
off
bALA
RGB colour mixing
red
Gree
5 0
5 0
255
255
ENTER ENTER
ENTER
UP & DOWN
UP & DOWN
ENTER
ENTER
bLue 50 255
ENTER UP & DOWN
ENTER
LED display invertion
ENTER
MENU
MENU
dS1P
d1SP
hour
Life time
0 9999
ENTER
Co63
UP
ShNd
Auto run
ENTER
UP
ShoU
CoL1 d000
d000
5000
d255
d255
5255
CoLo
ENTER
UP
ENTER
ENTER
ENTER
UP & DOWN
UP & DOWN
UP & DOWN
ENTER
ENTER
ENTER
Dimmer
Dimmer
Strobe - Slow to fast
ENTER
;uNp 5P00
d000
5P99
d255
UP
ENTERENTER
ENTER
UP & DOWN
UP & DOWN
ENTER
ENTER
Speed - Slow to fast
Dimmer
F@de 5P00
d000
5P99
d255
UP
ENTERENTER
ENTER
UP & DOWN
UP & DOWN
ENTER
ENTER
Speed - Slow to fast
Dimmer

www.prolight.co.uk HEX Par 9 User Manual
6
Master/Slave mode:
ToaccesstheMaster/Slavemode,pressthemodebuttonuntilthedisplayshowsSLNd
andpressthe“ENTER”button.Usethe“UP”and“DOWN”buttonstoselectNaSt(master)
orSLAV(slave)andthenpress“ENTER”toconrmyourselection.
Show mode:
Toaccessthecolourchangemode,pressthe“MODE”buttonuntilthedisplayshowsShNd
andpressthe“ENTER”button.Usethe“UP”and“DOWN”buttonstoselectthedesiredcolour
changemode(seebelow)andthenpress“ENTER”toconrmyourselection.
CoLo(StaticColour)press“ENTER”andthedisplaywillshowCoL1,press“ENTER”againandthe
displaywillshowCoL.Usethe“UP”and“DOWN”buttonstoselectthedesiredcolourCoL1-Co63
andthenpress“ENTER”toconrmyourselection.Youcannowsetthedimmerbypressingthe“UP”
buttonfollowedbythe“ENTER”button,nowusethe“UP”and“DOWN”buttonstoselectthedesired
brightnessd000-d255 andthenpress“ENTER”toconrmyourselection.
JuNP(colourchange)press“ENTER”andthedisplaywillshowSp00,press“ENTER”againand
usethe“UP”and“DOWN”buttonstoselectthedesiredcolourchangespeedSP00-SP99andthen
press“ENTER”toconrmyourselection.Youcannowsetthedimmerbypressingthe“UP”button
followedbythe“ENTER”button,nowusethe“UP”and“DOWN”buttonstoselectthedesiredbrightness
d000-d255andthenpress“ENTER”toconrmyourselection.
F@de(colourfade)press“ENTER”andthedisplaywillshowSp00,press“ENTER”againand
usethe“UP”and“DOWN”buttonstoselectthedesiredcolourfadespeedSP00-SP99andthen
press“ENTER”toconrmyourselection.Youcannowsetthedimmerbypressingthe“UP”button
followedbythe“ENTER”button,nowusethe“UP”and“DOWN”buttonstoselectthedesiredbrightness
d000-d255andthenpress“ENTER”toconrmyourselection.
RGB colour mixing:
Toaccessthecolourmixingmode,pressthe“MODE”buttonuntilthedisplayshowsbaLaandpress
the“ENTER”button.Usethe“UP”and“DOWN”buttonstoselectthedesiredcolourred,Gree,
bLueandthenpress“ENTER”toconrmyourselection.Usethe“UP”and“DOWN”buttonstoselect
thecolourlevel50-255thenpress“ENTER”toconrmyourselection.

www.prolight.co.uk HEX Par 9 User Manual
7
Operating instructions
Display On/Off:
ToaccesstheLEDdisplayon/offmode,pressthe“MODE”buttonuntilthedisplayshowsLed
andpressthe“ENTER”button.Usethe“UP”and“DOWN”buttonstoselectonoroffand
thenpress“ENTER”toconrmyourselection.
Display inversion On/Off:
ToaccesstheLEDdisplayinversionmode,pressthe“MODE”buttonuntilthedisplayshows
dISPandpressthe“ENTER”button.Usethe“ENTER”buttontoselecttheinversiononoroff
andpress“ENTER”toconrmyourselection.
Self test:
Toaccesstheselftestmode,pressthe“MODE”buttonuntilthedisplayshowstestand
pressthe“ENTER”button.ThexturewillnowrunanautotestonalltheLEDsandcolours.
Fixture hours:
Toaccessthexturehoursmode,pressthe“MODE”buttonuntilthedisplayshowshour
andpressthe“ENTER”button.Thexturewillnowshowthetotaloperatinghours.

www.prolight.co.uk HEX Par 9 User Manual
8
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
DMX setup
FurtherDMXcablescanbepurchasedfromallgoodsoundandlightingsuppliersorProlightConceptsdealers.
Pleasequote:
LEDJ1mInterior-
ExteriorDMXcable
LEDJ1mExterior
DMXcable
LEDJ2mExterior
DMXcable
LEDJ5mExterior
DMXcable
LEDJ10mExterior
DMXcable
Ordercode:LEDJ91 Ordercode:LEDJ141 Ordercode:LEDJ142 Ordercode:LEDJ143 Ordercode:LEDJ144
LEDJ1mExterior
Powercable
LEDJ2mExterior
Powercable
LEDJ5mExterior
Powercable
LEDJ10mExterior
Powercable
Ordercode:LEDJ146 Ordercode:LEDJ147 Ordercode:LEDJ148 Ordercode:LEDJ149
Also remember
that DMX cable
must be daisy
chained and
cannot be split.

www.prolight.co.uk HEX Par 9 User Manual
9
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterferance.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk HEX Par 9 User Manual
10
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk HEX Par 9 User Manual 11

www.prolight.co.uk HEX Par 9 User Manual 12