LEGRAND 0 489 36 User manual

Cat. No(s): 0 489 36
Technical data sheet: S000088483EN_3 Updated: 02/09/2022 Created: 02/01/2017
1/6
PIR corridor sensor
(DALI)
CONTENTS Page
1. Use ......................................1
2. Technical characteristics ..................1
3. Installation...............................2
4. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
5. Connection ..............................3
6. Operation................................4
7. Settings..................................4
8. Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
9. Care .....................................6
10. Standards...............................6
11. Troubleshooting ........................6
1. USE 2. TECHNICAL CHARACTERISTICS
DALI sensor Cat. No: 0 489 36 uses PIR (passive infrared) technology to
detect movement, and also incorporates an light level meter.
It can be surface-mounted on a concrete ceiling using box
Cat. No. 0 488 75, or ush-mounted directly in a suspended ceiling using
claws or in a ush-mounting box Cat. No. 0 800 31.
It is suitable for indoor passageways such as corridors, and can manage
a group of 64 ECGs maximum.
This sensor is fully congured using conguration tool Cat. No. 0 882 30/
BMSO4001 with which it is possible to:
• Control a single zone or group
• Distribute DALI ECG addresses
• Pair DALI ECGs with their sensor
• Designate Master and Slave sensors
• Dene the standby level when there is no detection
• Dene the standby time
• Congure all the other sensor settings (for example, daylight
setpoint, time the lighting remains on after detection, choice of
detection technology, operating mode, etc.)
DALI sensor Cat. No. 0 489 36 is powered with 16 VDC by the DALI bus.
A DALI power supply Cat. No. 0 035 15 or 0 035 13 can supply this voltage
to the DALI BUS with a maximum of 200 mA.
Voltage: 16 V=
No-load power consumption: 10 mA
Usage temperature: -5°C to +45°C
Storage temperature: -20°C to +70°C
Impact resistance: IK04
Penetration by solid and liquid matter: IP41
Weight: 114 g
Light level cell
Light level test
Test button
IR transmission/
reception cell
Learn LED
PIR sensor

2/6
Technical data sheet: S000088483EN_3 Updated: 02/09/2022 Created: 02/01/2017
Cat. No(s): 0 489 36
PIR corridor sensor
(DALI)
CONTENTS
Without protective cover
3.1 Sensor location
3.2 Recommended light exposure
3. INSTALLATION
PIR
2.5 m
1.5 m
3.3 Mounting
3.4 Recommended light exposure
3.5. Removal
3. INSTALLATION (CONTINUED)
0.3 to
20 mm
Ø 65
Ø 65
Ø 68
Ø 68
50
0 488 75
Ø 120
Ø 120

3/6
Technical data sheet: S000088483EN_3 Updated: 02/09/2022 Created: 02/01/2017
Cat. No(s): 0 489 36
PIR corridor sensor
(DALI)
CONTENTS
4. DIMENSIONS
50 73
52
Ø : 122
5.1 Wiring with a single sensor:
5. CONNECTION
D
5.2 Wiring with several sensors
5. CONNECTION (CONTINUED)
D
x 64 max.
0 488 72
Cat. Nos. 0 035 13/15
200 mA max.
D
≤100 m 0.5 mm2
≤150 m 0.75 mm2
≤300 m 1.5 mm2
10 mA
2 mA
0 488 72
Cat. Nos. 0 035 13/15
200 mA max.
x 64 max.

4/6
Technical data sheet: S000088483EN_3 Updated: 02/09/2022 Created: 02/01/2017
Cat. No(s): 0 489 36
PIR corridor sensor
(DALI)
CONTENTS
5. CONNECTION (CONTINUED)
0 488 78
• The push-button must be
connected to a master sensor
via Cat. No. 0 488 78.
D
150 m. max.
D
≤100 m 0.5 mm2
≤150 m 0.75 mm2
≤300 m 1.5 mm2
10 mA
2 mA
Cat. Nos. 0 035 13/15
200 mA max.
0 488 72
0 488 72
0 488 78
x 64 max.
6.1 TEST function
6.2 Configuration
Configuration of a DALI installation is described in the DALI programming
manual.
7.1 Detection settings
Time delay: Length of time the load is on after
detection.
Pulse mode (= push-button mode): If the time delay is set to
0, the sensor is in push-button mode. In this case, there is a
10-minute time delay before the load is switched off. If the setting
is overridden or there is a new detection, the 10-minute time delay
starts again.
Available with configuration tool 0 882 30/BMSO4001.
Sensitivity: Detection range setting.
6. OPERATION
Sensor settings Default
value
Modiable
parameters
Conguration
tools
0 882 30
BMSO4001
Time delay 15 min 5 s - 2 hrs
Sensitivity PIR
(very high)
Low, medium,
high, very high
Modes
Auto on/Auto o Active Enable/
Disable
Walkthrough Inactive Enable/
Disable
Manual on/
Auto o Inactive Enable/ Disable
Detection
system
Initial PIR Not modiable
Maintain PIR
Alarm Inactive Enable/
Disable
Not modiable
7. SETTINGS
5.3 Wiring with several sensors and one control unit:

5/6
Technical data sheet: S000088483EN_3 Updated: 02/09/2022 Created: 02/01/2017
Cat. No(s): 0 489 36
PIR corridor sensor
(DALI)
CONTENTS
7.1 Detection settings(continued)
Auto on/Auto off mode:
The lighting switches on automatically:
- On detection of presence if the natural light level is insufficient.
The lighting switches off automatically:
- Where no presence is detected and at the end of the time delay
set
- Or if the natural light level is sufficient (regulation activated)
Another detection causes automatic switch-on if there is
insufficient light.
Walkthrough mode:
- If no presence is detected in the 20 seconds following an initial
detection, the device will switch off the load after 3 minutes.
- If another movement is detected in the 3 minutes following
initial detection, the device will switch off the load at the end of
the set time delay.
Manual on/Auto off mode:
The lighting is switched on via a manual control, but switches off
automatically:
- Where no presence is detected and at the end of the time delay
set
After switch-off, if another movement is detected within a
30-second period, the lighting switches on automatically.
The Restart function must be enabled.
After 30 seconds, the lighting has to be switched on manually.
Detection system:
Initial detection: The load is switched on as soon as the first detection
occurs if the natural light level is below the light level threshold.
Maintain: The load remains active if another presence is detected.
Restart: In manual mode. After switch-off, any new detection within a
30-second period triggers an automatic switch-on.
After 30 seconds the device must be switched on manually.
Possible in Manual on/Auto off mode only, by disabling the Detection
System: "Initial"
Alarm: An audible signal is emitted before switch-off. 1 minute before,
then 30 seconds, then 10 seconds.
7.2 Light level settings
Daylight setpoint: Value at which the load comes on if the natural
light level is less than the setting.
Eye function: Value 0 (eye on configuration tool 0 882 30/
BMSO4001) is used to save the ambient light level in the room as a
daylight setpoint.
7. SETTINGS (CONTINUED)
Sensor settings Default
value
Modiable
parameters
Conguration
tools
0 882 30
BMSO4001
Daylight setpoint 150 lux 5 - 1275 lux
Advanced
mode
Calibration −0- 99995 lux
Light regulation Active Enable/
Disable
Light contribution
Auto Auto - 1275 lux
7.2 Light level settings (continued)
Advanced mode:
Calibration: The ambient light level measured with a luxmeter
must then be transmitted to the sensor.
Regulation: Automatic switch-off of the load 10 minutes after the
daylight setpoint is exceeded with an additional safety threshold
(to avoid lights switching off at the wrong moment).
Light contribution: Quantity of additional lux provided by the load
being switched on.
When the light contribution parameter is set to "Auto" on configuration
tool Cat. No. 0 882 30/BMSO4001, the sensor automatically calculates
how much light is provided.
7.3 Modifying the settings using the configuration tool
• 0 882 40: Configuration gateway and Legrand Close Up application.
The Close Up application is available on the Apple Store and the Play Store
The detector functions are controlled by a number of parameters which
can be changed or programmed by an infrared configurator.
In combination with configuration tool 0 882 40, the Legrand Close Up
smartphone app can be used to view and modify all the detector
parameters with online help.
Point the infrared configuration tool at the detector and send the
necessary programming commands to the unit as indicated in the table
below.
For more information about setting parameters, refer to the data sheet
for the configuration gateway Cat. No. 0 882 40.
0 882 30/BMSO4001: configuration tool
When the sensor receives an IR command via the configuration tool, a
red LED lights up acknowledging the modification.
For more information about setting parameters, refer to the data sheet
for the configuration tool Cat. No. 0 882 30.
Google PlayApp Store
As from 01/01/2022, this product
ref. 0 882 30 is no longer sold.

Technical data sheet: S000088483EN_3 Updated: 02/09/2022 Created: 02/01/2017
Cat. No(s): 0 489 36
PIR corridor sensor
(DALI)
CONTENTS
Keep the lens clean.
Clean the surface with a cloth.
Do not use acetone, tar-removing cleaning agents or trichloroethylene.
Resistant to the following products: - Hexane
- Methylated spirit
- Soapy water
- Diluted ammonia
- Bleach diluted to 10%
- Window-cleaning products
Caution:
Always test before using other special cleaning products.
8. PERFORMANCE
Height
m :1
21
20
c
a
b
Low sensitivity
(25%)
Medium sensitivity
(50%)
a (m)b(m)c(m)a(m)b(m)c(m)
Height (m)
2.5 7103 81
43
37103 81
43
3.5 9103121
43
410 8313
93
High sensitivity
(75%)
Very high sensitivity
(100%)
a (m)b(m)c(m)a(m)b(m)c(m)
Height (m)
2.5 10 163162
43
310 163162
43
3.5 14 16 3172
43
415 103181
43
9. CARE
10. STANDARDS
Directive: EC
Installation standards: NFC 15-100
Product standards: NF EN 50428
Environmental standards:
- European directive 2002/96/EC:
WEEE (Waste Electrical and Electronic Equipment)
- European directive 2002/95/EC:
RoHS (Restriction of Hazardous Substances)
- Decrees and/or regulations: Public buildings
Workplace buildings
High-rise buildings
11. TROUBLESHOOTING
PROBLEMS CAUSES SOLUTIONS
The lighting stays on when there is no-one
present
1- Reduce the sensitivity level
2-
3-
Regulation function inactive
Daylight setpoint too high
Too much light provided
Enable the regulation function
Reduce the light level threshold
Decrease the power of the luminaires
Time delay too short
Detection sensitivity too low
Daylight setpoint too low
Increase the time delay
Increase the sensitivity
Move the sensor closer to the work area
Increase the threshold
The lighting does not switch o during the
day when there is an adequate natural light
level
The lighting switches o when there are
people present and the natural light level is
inadequate (darkness)
Sources of interference such as draughts,
vibration or radiators may cause nuisance
tripping If the interference continues with the
conguration tool, go into Detection
system, select Maintain and then choose
PIR or US detection
If the interference still continues, move
the sensor away from sources of
interference
Check that the sensor is positioned correctly
in relation to the window
5 to 15 minutes is recommended for
work areas