LEGRAND 430 521 User manual

3.8-38 mm 10X motorized day/night dome colour camera
430 521
3.5-94.5 mm 27X motorized day/night dome colour camera
430 522
3.8-38 mm 10X weatherproof motorized day/night dome colour
camera
430 523
3.5-94.5 mm 27X weatherproof motorized day/night dome colour
camera
430 524
3.5-129.5 mm 37X weatherproof motorized day/night dome colour
camera
430 525
430 521
430 522
430 523
430 524/525
Instructions manual
LE03668AA

_________________________________________________________________________________
2
IMPORTANT SAFETY GUIDE
Read, heed and follow all the Instructions
Read all the safety and operating instructions before using the product.
Keep this manual
Keep this manual for reference in future.
Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.
Installation
Do not install near any heat resources such as radiators, heat registers, stoves,
or other appratus including amplifiers that product heat. Improperly installed
product may fall, cause serious injury to a child or adult and damage the
product.
Do not block any ventilation holes or openings. Install in accordance with the
manufacturer‟s instructions.
Use only with the cart, stand, tripod, bracket, mounting devices, or table
specified by the manufacturer.
Installation should be done only by qualified personnel and conform to all the
instructions by the manufacturer.
Refer all servicing to qualified service personnel.
Unless the product is specifically marked as IP67, more than IP67 or confirmed by
the manufacturer, it is designed for indoor use only and it must not be installed
where exposed to rain and moisture.
Do not load on the product.
Use stainless steel hardware to fasten the mount.
To prevent damage from water leakage when installing a mount outdoors on a roof
or wall, apply sealant properly around holes.
These servicing instructions are for use by qualified service personnel only. To
reduce the risk of electric shock, do not perform any servicing other that
contained in the operationg instructions unless you are qualified to do so.
Use only replacement parts specified by the manufacturer.
Power source
This product should be operated only from the type of the power source indicated
on the marking label.

_________________________________________________________________________________
3
CAUTION
Operating
Before using, make sure that the power supply and others are properly installed.
While operating, if any abnormal condition or malfunction is observed, stop using the
product immediately and then contact your local dealer.
Handling
Do not disassemble or tamper with the parts inside the product.
Do not drop or subject the product to shock and vibration as this can damage the
product.
Care must be taken when you clean the clear dome cover. Especially, scratch and dust
will ruin the quality of the product.
Installation and Storage
Do not install the product in areas of extreme temperature, which exceed the allowable
range.
Avoid installing in humid or dusty places.
Avoid installing in places where radiation is present.
Avoid installing in places where there are strong magnetic fields and electric
signals.
Avoid installing in places where the product would be subject to strong vibrations.

_________________________________________________________________________________
4
TABLE OF CONTENTS
1 Introduction
1.1 Model Code
5
1.2 Features
6
1.3 Package Components
8
1.4 Main Part Description
11
2Installation
2.1 DIP Switch Setup
15
2.2 In-Ceiling Mount Installation (MPS)
21
2.3 Installation with Surface Mount Bracket (MPS)
22
2.4 Direct Installation on the Ceiling Mount
Bracket(MPS)
23
2.5 Installation using Wall Mount Bracket(MPS)
26
2.6 Installation with Ceiling Mount Bracket(MAO/MAI)
27
2.7 Installation with Wall Mount Bracket(MAO/MAI)
28
2.8 Wiring and Cabling
29
3Operation
3.1 Check Point before Operation
34
3.2 Check Points for Preset and Pattern Function
before Operation
34
3.3 OSD Menu
35
3.4 Reserved Presets (Hot Keys)
35
3.5 Preset
36
3.6 Swing
36
3.7 Pattern
37
3.8 Group
38
3.9 Other Functions
39
3.10 OSD Display
40
4OSD Menu
4.1 Quick Programming Guide
41
4.2 Main Menu
41
4.3 Display Setup
42
4.4 Privacy Zone Mask Setup
44
4.5 Camera Setup
46
4.6 Motion Setup
50
4.7 Preset Setup
53
4.8 Swing Setup
57
4.9 Pattern Setup
58
4.10 Group Setup
59
4.11 System Initialization
62
5Specifications
63
5.1 Dimension
68

_________________________________________________________________________________
5
1. INTRODUCTION
1.1 MODEL CODE
Ref.
430 521
430 522
430 523
430 524
430 525
Serie
Mini
plastic
small
Mini
Aluminium
with
fan/heater
Mini
Aluminium
with
fan/heater
Aluminium
with
fan/heater
Aluminium
with
fan/heater
Outdoor
serie
NO
YES
Video signal
PAL
Wall mount
bracket
NO
YES
Rated power
:
12 VDC
Sensor
3 In / 1
Out
4 In / 2
Out
3 In / 1 Out

_________________________________________________________________________________
6
1.2. FEATURES
Powerful Zoom Camera & Setup Options
430 521
430 522
430 523
430 524
430 524
Optical Zoom
10
x27
x10
x27
x37
Digital Zoom
10
x12
x10
x12
x12
Max. zoom
magnification
100
324
x100
x324
x444
High light
compensation
NO
NO
YES
YES
YES
Privacy Masks
4
8
4
8
8
Day & Night
YES
WDR
NO
YES
Focus Mode
Auto-Focus, Manual Focus, Semi-Auto Focus
OSD Menu
YES
Image Sensor ¼ ” CCD
Sony
interline
Transfer CCD
super HAD
color CCD
Sony
Interline
Transfer
CCD
super HAD color CCD
Powerful Pan/Tilt Functions
MAX. 360 /sec High Speed Pan/Tilt Motion
With the Vector Drive Technology, Pan/Tilt motions are accomplished along the
shortest path. As a result, the time to target view is remarkably short and the
video on the monitor is very natural in monitoring.
With the Micro-Stepping Control Technology, the video looks very natural at high
zoom magnification during a jog operation on a controller since the camera can be
controlled by 0.05 /sec. Hence it is very easy to make the camera focus on
desired target views at high zoom magnification. Additionally it is easy to make
the camera focus on desired positions with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More…
MAX. 127 Presets are programmable and each preset can have its own parameter
values independently from the other presets.
For an example, refer to the below table.
Preset
No.
White
Balance
Auto
Exposure
•••
Label
Remarks
Preset 1
Case A
Case 3
“E NTRANCE
”
Preset 2
Case C
Case 5
“W AREHOUS
E”

_________________________________________________________________________________
7
Preset 3
Case V
Case 2
“O FFICE ”
•••
Preset
95
Reserved for OSD Menu
•••
Preset
128
Case K
Case 9
“T ERRACE ”
MAX. 4 Patterns are programmable. This function is that the camera memorizes the
path (mostly curve path) by the joystick of the controller and revives the
trajectory operated by the joystick as closely as possible.
MAX. 8 sets of Group are programmable. This function is that the camera memorizes
the combination of Presets, Pattern and/or Swings sequently and runs Presets,
Pattern and/or Swings repetitively. A Group can be combined upto 20 functions
with any of Preset/Pattern/Swing.
Privacy Masks are programmable, not to intrude on any other‟s privacy :
430 522/430 524/430 525 : 8 privacy zones
430 521/430 523 : 4 privacy zones
PTZ (Pan/Tilt/Zoom) Control
With the RS-485 communication connection, MAX. 255 units of cameras can be
connected to a single controller.
Pelco-D or Pelco-P protocols can be selected as a control protocol in the current
firmware version.
OSD (On Screen Display) Menu
OSD menu is provided to display the status of camera and to configure the
functions interactively.
The information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and
Preset is displayed on screen.
Alarm In/Out Function
430 522 : 4 alarm sensor inputs and 2 alarm output relays
430 521/430 523/430 524/430 525 : 3 alarm sensor inputs and 1 alarm sensor
outputs
Alarm sensor input is decoupled with photo-couplers to avoid external electric
noise and shock perfectly.
Both of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and
the signal range of the sensor input is from DC 5.0V to 12.0V for various
applications.
The camera can be set to move to a Preset position or to run functions such as
Pattern, Swing and Group when there are external sensor activations. Also “Post

_________________________________________________________________________________
8
Alarm ”function is possible, which is supposed to activate after user-defined
time period and sequentially in succession to the action by external sensor
activations.
Reserved Presets (Hot Keys)
Most camera setup options can be set up easily and directly with the reserved
presets (Hot Keys), without entering into OSD menu. For more information, refer
to “Reserved Presets(Hot Keys) ”in this manual.
Perfect Outdoor Environment Compatibility and Easy Installation
430 523/430 524/430 525 : The fans and heaters are built-in in the camera for
cold and hot temperature environment. Also idealistic mechanical design protects
the camera from water and dust. (IP67 when installed properly with wall mount
bracket only)
It is easy to install the camera.

_________________________________________________________________________________
9
1.3. Package Component (430 521 Model)
Product & Accessories
Main Body & Surface Mount Bracket
Default Accessories
[Main Cable, Calblock, Screws : Tapping M4 16,
Tapping M4 25, Machine M3 6, Machine M3 8]
I/O Cable

_________________________________________________________________________________
10
Package Component (430 522 Model)
Product & Accessories
Main Body / Terminal Cover
Dome Cover
Screws
Optional brackets
In-Ceiling Mount Bracket
430 596
Ceiling Mount Bracket
430 597
Corner bracket
430 598
Wall mount bracket
430 594

11
Package Component (430 523/430 524/430 525 Models)
Product & Accessories
Main Body & Surface Mount Bracket
Default Accessories
[Main Cable, Wrench]
Accessories for The Models with Alarm
In/Out Function [I/O Cable]
Wall Mount Bracket
[Screws : Machine M5 15, Hex Lag #14 50]
Optional Brackets
Corner bracket 430 598
Ceiling Mount Bracket 430 595
Pole bracket 430 599

_________________________________________________________________________________
12
1.4. Main Part Description (430 521 Model)
Dome Cover
Do not detach the protection vinyl from the dome cover
before finishing all the installation process to protect
the dome cover from scratches or dust.
Dome Cover Lock-up
Screw
Used to lock up the dome cover after assembling the dome
cover with the main body.
Dome Cover Assembly
Stud
Used to line up the stud on the main body and the stud on
the dome cover when assembling the dome cover with the
main body.
DIP Switch
Used to set up camera IDs and protocols.
Surface Mount
Bracket
& Mounting Screw
Hole
Used for surface mount type, wall mount type and ceiling
mount type. They are not used for in-ceiling mount type.
Main Connector
Used for the power wire, the video cable and the RS-485
communication cable connection.
Sensor I/O Port
Used for the sensor in/out connection.

13
Main Part Description (430 522 Model)
Dome Cover
Do not detach protection vinyl from dome cover before
finishing all installation process to protect dome cover
from scratches or dust
Terminal Cover
This is used to install the camera directly on the
ceiling or attach to the other brackets such as in-
ceiling, ceiling and wall mount. After separating this
cover first and then attach this directly to ceiling or
to the other bracket. Camera must be assembled at the
last stage.
Drop Prevention
Spring
Drop Prevention
Hook
This part keeps the camera from dropping during
installation and maintenance. After install the Terminal
Cover, please, hang the spring to the drop prevention
hook of main body as shown in picture for further tasks.
Lockup Screw
After assembling Terminal Cover to main body, screw
Terminal Cover to main body to protect them from
separation by vibration and so on.
Fuse
If the fuse is burnt to protect your came from over-
current damage, the fuse have to be replace with new one.
The fuse specification is 250V 2A. However, we recommend
consulting with supplier to remove the cause of over-
current.
Cabling Terminal
During installation, Power, Video, Communication, Alarm

_________________________________________________________________________________
14
Block
I/O cables are connected on to this cabling terminal
block.

15
Main Part Description (430 523 Model)
Mounting Hook
DIP Switch
Main Connector
Sensor I/O Port
Dome Cover
Mounting Screw Hole
Main Body / Terminal Cover
Dome Cover
Do not detach the protection vinyl from the dome cover
before finishing all the installation process to protect
the dome cover from scratches or dust.
DIP Switch
Used to set up camera IDs and protocols.
Mounting Hook
Used to assemble the main body with wall mount bracket or
ceiling mount bracket. Insert the mounting hooks into the
holes on the surface of the main body and turn the main
body.
Mounting Screw Hole
Used to assemble the main body with a bracket with
screws.
Main Connector
Used for the power wire, the video cable and the RS-485
communication cable connection.
Sensor I/O Port
Used for the sensor in/out connection.

_________________________________________________________________________________
16
Terminal Cover Disassembling
①Remove the Lockup Screw as shown
bellow.
②Turn main body on its axis in
CCW(Counter-clockwise) direction and
separate it from Terminal Cover.
Terminal Cover Assembling
①Check if the summit of the Plate
Spring is located at the arrow mark as
shown in the dotted circle.
②Check the 2 mold line for assembly
before starting assembly. Line up the
mold lines as shown in the dotted
circle and turn main body on its axis
in CW(Clockwise) direction and
assemble main body to Terminal Cover.
After assembling them, screw main
body to Terminal Cover to protect
them from separation by vibration and
so on.

17
2. INSTALLATION
2.1 DIP Switch Setup (430 521/430 523/430 524/430 525 models)
Before installing the camera, set up the DIP switch to configure the camera ID
and the communication protocol.
Camera ID Setup
ID numbers of cameras are set up with binary numbers. See the examples shown below.
Pin
1
2
3
4
5
6
7
8
Binary Value
1
2
4
8
16
32
64
128
Ex : ID=5
on
off
on
off
off
off
off
off
Ex : ID=10
off
on
off
on
off
off
off
off
The camera ID range is “ 1~255 ”. Camera ID must not be “0”!
The factory default of the camera ID is “1”.
Match the camera ID with the Cam ID setting of your DVR or Controller to control the
camera.
If you are connecting a single camera to a controller, terminate the camera. When
connecting more than one camera to a single controller, terminate the last camera on
the communication line. The last camera means the camera farthest in cable length
from the controller.
Note that the total length of the communication cable between a controller and the
camera(s) on the same communication line must be less than 1.2Km.
ON
ON
1
2
3
4
5
6
7
8

_________________________________________________________________________________
18
Communication Protocol Setup
Select an appropriate Protocol with the DIP switch combination.
Switch Mode
Protocol
P0
(Pin 1)
P1
(Pin 2)
P2
(Pin 3)
OFF
OFF
OFF
PELCO-D, 2400 bps
ON
OFF
OFF
PELCO-D, 9600 bps
OFF
ON
OFF
PELCO-P, 4800 bps
ON
ON
OFF
PELCO-P, 9600 bps
Others
Reserved
Match the camera protocol with the camera protocol in the setting of your DVR or
controller to control the camera.
Adjust the DIP switch after turning off the camera. If you changed the camera
protocol by changing the DIP S/W, the change will be effective after you reboot the
camera.
The factory default protocol is “Pelco-D, 2400 bps ”.

19
Terminal Resistor Setup
The terminal resistor is used for the following cases.
Case 1 : In case that the control cable length between a camera and a controller is
relatively very long (1:1 Connection)
If the communication cable length is very long, the electrical signal will bound in the
terminal point. This reflected signal causes distortion of original signal.
Accordingly, the camera can be out of control. In this case, the terminal resistor of
both sides i.e. the camera and the controller must be set to „ON‟state.
Case 2 : In case that multiple cameras are connected to a controller.
Due to similar reasons with the case 1, the terminal resister of the controller and the
last camera must be set to „ON‟state. The last camera means the camera farthest in
cable length from the controller. Do not turn on the terminal resistor of all the
cameras on the same communication cable.

_________________________________________________________________________________
20
DIP Switch Setup (430 522 model)
Before you install the camera, you should set the DIP switches to configure the
camera ID, communication protocol. Do not use the ISP connector. (Authorized person
only !)
Camera ID Setup
ID number of camera is set using binary number. The example is shown bellow.
Pin
1
2
3
4
5
6
7
8
ID Value
1
2
4
8
16
32
64
128
ex: ID=5
on
off
on
off
off
off
off
off
ex: ID=10
off
on
off
on
off
off
off
off
The range of ID is 1~255. Do not use 0 as camera ID. Factory default of Camera ID is
1.
If you want to control a certain camera, you must match the camera ID with Cam ID
setting of DVR or Controller.