LEGRAND ELIOT Kit STOP&GO Connected User manual

1/16
LEGRAND - BP30076
87045 LIMOGES CEDEX FRANCE
Telephone: [phone] –Fax: [phone]
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
CONTENTS PAGE
1. Description - Use.................................1
2. Product range .....................................1
3. Overall dimensions.............................. 1
4. Preparation - Connection ....................2
5. General characteristics........................8
6. System architecture ..........................12
7. Conformities and approvals...............13
8. Auxiliaries and accessories ...............14
9. Application messages .......................15
1. DESCRIPTION - USE
Device dedicated to guarantee service continuity.
Via the app “POWER ON”(available for free on Google Play and
Play Store), gives to the user information on the status of the
associated circuit (open/ closed/ tripped ...).
In case of unwanted tripping (temporarily electrical disturbances or
other external events) and if no permanent fault is detected: it sends
a notification to user in order to get an authorization to remotely
switch ON the associated device.
In case of permanent fault: the user will be informed about it without
having the possibility to remotely switch on the power, to guarantee
total security.
The associated circuit must be protected by a 1 module per pole
DX3RCCB or RCBO up to 63 A. (not delivered with the kit).
2. RANGE
. Cat. n° 4 149 54: Eliot Kit Stop&Go Connected, composed by:
Non-automatic resetting Stop and go (cat. no 4 149 54)
. During a “normal situation”:
- It permanently checks the status of the installation.
- It gives remotely a series of information to the user: circuit
open/closed, manually open/closed, ...
. Following an “unwanted tripping” due to a non-permanent fault:
- It reports the information through the Smartphone app
- Allows the user to remotely switch it ON
- In case of recurrent non-permanent faults, the Stop&Go will not
allow some remote command (see details on page 5)
. Following an “unwanted tripping” due to a permanent fault (earth
leakage or short circuit):
- It reports the information through the Smartphone app
- It does not allow the use to remotely switch-On the device and
advises to contact an electrician to check the installation.
. Technology: DC electric motor with permanent magnets
. 2 modules (35,6 mm) width
. Rated Voltage & Frequency: 230 V ~ 50 / 60 Hz with standard
tolerances.
. Operating voltages:
Minimum (0,85 x Un): 195,5 V
Maximum (1,1 x Un): 253 V
2. RANGE (continued)
Wi-Fi interface module (cat. no 4 149 52)
To communicate with the Smartphone through a Wi-Fi Box
. 1 module (17,8 mm) width
. Supplied by the Power supply module via supply patch cord
. Equipped with a 1m length pre-cabled cable to connect with the
Stop&Go
Power Supplier Module for the Wi-Fi interface (cat. no 4 149 45)
. Primary voltage 95÷250 V~
. Secondary voltage 12 VDC 500 mA
. 1 module (17,8 mm) width
Supply patch cord:
. Allows to connect the Power supply module with the Wi-Fi interface
at the downstream through dedicated connectors.
. Length: 250 mm
Configuration & use:
. Must be used with the app “POWER ON”
. To be downloaded for free on Google Play or Play Store
All the configurations steps are explained in the app.
Note: This part can be done without any ADSL Wi-Fi box thanks to
the Wi-Fi module which allows to display its own network for this
step.
3. OVERALL DIMENSIONS
. Stop&Go
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016

2/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
3. OVERALL DIMENSIONS (continued)
. Wi-Fi interface module (already equipped with an external Half
Wave 2.4GHz Antenna With RP-SMA Connector):
. Power supply module:
. Supply patch cord:
L = 250 mm
4. PREPARATION - CONNECTION
Fixing:
. On symmetric rail EN/IEC 60715 or DIN 35.
Operating positions:
. Vertical, Horizontal, backwards, on the side
Power Supply:
Primary voltage 95÷250 V~
Secondary voltage 12 VDC 500 mA
. Power distribution towards the interface via specific 250 mm supply
patch cord (delivered with the kit) to connect at the downstream of
the supplier indifferently in one of the two dedicated ports
Supply of the Wi-Fi Interface:
. Mandatory in 12 VDC via the specific Power supply module and
specific supply patch cord 250 mm length (delivered with the kit) to
connect at the downstream through dedicated port
Supply of the Stop&Go:
. Supply Phase and Neutral from the top on the extractable
connector.
. It is mandatory to connect Phase and Neutral downstream of the
associated device and the protection conductor to the connector at
the bottom of this device. Stop&Go will not work correctly if the
protection conductor is not connected.
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016
Connection cable to
the Stop&Go

3/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
4. PREPARATION - CONNECTION (continued)
List of possible associations:
. DX32P RCCBs
. DX32P RCBOs (2 poles protected or P+N, 1 pole protected)
Association Stop &Go - Protection device:
. To be fitted to the left of 1 module per pole wide DX3 RCCB’s 2P or
DX3 RCBO’s ≤ 10000A (1P+N et 2P ≤ 63 A)
. No tool required. Clipped to the associated device by mean of
plastic clamps.
Wiring diagrams:
. Stop&Go
Note: It is not necessary to install a specific protection upstream of
the Stop&Go because it is self-protected
4. PREPARATION - CONNECTION (continued)
Wiring diagrams (continued) :
. Power supply module:
protected by an MCB:
protected by a Fuse holder:
Connection:
. Terminals protected against accidental contact (IP20, wired
devices).
Terminals:
. Stop&Go
Terminal depth: 8 mm.
Stripping length: 8 mm
. Supply module
Terminal depth: 8 mm.
Stripping length: 8 mm
Screw head:
. Stop&Go
Slotted, diameter 3.5 mm
. Supply module
Mixed, slotted and Pozidriv n°1 (UNI7596 type Z1).
Recommended tightening torque:
. Stop&Go
0,4÷0,5 Nm.
. Supply module
1 Nm
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016

4/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
4. PREPARATION - CONNECTION (continued)
Recommended tools:
. For the terminals of the Stop&Go: flat screwdriver 3,5 mm.
. For the terminals of the Supply modules: Pozidriv n°1 or flat
screwdriver 4 mm.
. For fixing: flat screwdriver 5.5 mm (6 mm maximum).
Conductor type:
. Copper cables
. Stop&Go
Without ferrule
With ferrule
Rigid cable
1 x 2,5 mm²
2 x 1,5 mm²
-
Flexible cable
1 x 2,5 mm²
2 x 1,5 mm²
1 x 2,5 mm²
2 x 1,5 mm²
. Supply module
Without ferrule
With ferrule
Rigid Cable
1 x 1,5 mm²
2 x 1,5 mm²
-
Flexible Cable
1 x 1,5 mm²
2 x 1,5 mm²
1 x 1,5 mm²
2 x 1,5 mm²
Kit assembling:
1. - 2. Connect Power supply module and Wi-Fi interface with the
250 mm Supply patch cords.
3. Connect Wi-Fi interface and Stop&Go with the pre-cabled 1 m
length cable in the dedicated port of the Stop&Go
Note: the length of 1m allows to clip the Wi-Fi module (and the
power supply) on a different DIN row, than the Stop&Go module.
4. PREPARATION - CONNECTION (continued)
Diagnostic procedure:
. Once the kit assembly and the electrical connections have been
made, it is advisable to carry out a diagnostic procedure to check the
good communication between the Stop&Go module and the Wi-Fi
interface.
. Necessary material:
- kit Stop&Go
- smartphone with a Wi-Fi connexion
. Procedure:
1. Close the Stop&Go via the two handles (isolating + power
upward)
2. Put the Wi-Fi interface in configuration mode pressing the fron
face button for about 7 seconds, until the “Wi-Fi” LED flashes rapidly
in orange.
The interface is now in programming mode and it creates its own
network (S&G_WIFI_xxxxx)
3. Connect the smartphone to the Wi-Fi network created by the
interface (network: S&G_WIFI_xxxxx)
4. Open a web browser page and enter the IP address
192.168.1.1 to connect to the diagnostic web page of the Wi-Fi
interface and press “START TEST”
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016

5/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
4. PREPARATION - CONNECTION (continued)
Diagnostic procedure (continued) :
5. Test 1/3 - Set the AUTO/MAN selector to “MAN” (the Stop&Go
LED flashes slowly in green)
Once the test is complete, press “Next” to proceed to the next test.
6. Test 2/3 - Set the AUTO/MAN selector to “AUTO” (the Stop&Go
led is steady green)
Once the test is complete, press “Next” to proceed to the next test.
7. Test 3/3 - Simulation of a non-permanent fault and a remote
reclosing
7.1 Press the “TEST” button of the protection device associated to
the Stop&Go (the Stop&Go power handle is down, and the
isolating handle is up and the Stop&Go led flashes quickly in red)
7.2 An alert message is displayed
7.3 Press on “TURN ON”
4. PREPARATION - CONNECTION (continued)
Diagnostic procedure (continued) :
7. Test 3/3 - Simulation of a non-permanent fault and a remote
reclosing (continued)
7.4 Press “OK” to confirm the reclosing (the two Stop&Go handles
are upward and the Stop&Go led goes steady green)
Once the test is complete, press “Finish”.
Note:
a. It is always possible to repeat the procedure by pressing “Restart
test”
b. If one or more tests fail:
- check the connection between the Stop&Go and the Wi-Fi
interface
- Repeat the test procedure
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016

6/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
4. PREPARATION - CONNECTION (continued)
On site information displayed by the Stop&Go:
Stop&Go lockout:
. By the sliding front face.
Sliding front face downward: the associated device goes into OFF
position and manual or automatic closing operations are disabled.
Sliding front face upward: the device is operating.
. Lockout by padlock Φ 4mm, only when the sliding front face is
down.
Then mechanical and electrical controls are not possible.
Display of the device status and the status of the contacts of
the associated device:
. By handle mark:
“O-Off“ white on a green background = device switched-off and
contacts opened.
“I-On” white on a red background = device powered-on and
contacts closed.
Device handle status:
. The handle of the Stop&Go, consists of two parts:
- an “isolating” handle
- a “power” handle
. Operation sequences:
- “Normal situation”: both handles upward.
4. PREPARATION - CONNECTION (continued)
On site information displayed by the Stop&Go (continued) :
Device handle status (continued) :
. Operation sequences (continued) :
- In case of an “Unwanted tripping” of the associated device and
during the verification of the state of the electric circuit:
the power handle is down.
the isolating handle is up.
➔The Stop&Go can be remotely controlled via the Smartphone
app
- If the Stop&Go detects a permanent fault after a tripping or a too
recurrent non-permanent fault (3 faults and 3 remote closing
operations in a time of 5 minutes), the isolating handle goes down
➔The Stop&Go cannot be anymore remotely controlled via the
Smartphone app
Note: Refer to the § Details for “too recurrent” non-permanent faults”
for all details on recurrent faults
Resetting by the Stop&Go handle:
. The local resetting of the Stop&Go and of the associated device
can be carried out by the Stop&Go handle (isolating and power
handles together)
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016
Isolating handle
Power handle
Isolating handle
Power handle
Isolating handle
Power handle
Isolating handle
Power handle
Isolating handle
Power handle

7/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
4. PREPARATION - CONNECTION (continued)
On site information displayed by the Stop&Go (continued) :
Details for “too recurrent” non-permanent faults:
During its functioning, the Stop&Go memorises the numbers of
faults and of remote/manual resetting operations.
. When an event occurs, the Stop&Go analyses the event and in
case of fault (short-circuit or ground fault) it starts the recurring fault
procedure.
. See table for details:
# of faults
Period
Consequence
3
≤ 5 minutes
- Remote resetting is disabled.
- The application shows this state
with the following message:
3
≤ 1 hour
- The application shows this
condition with a message indicating
the number of faults within the time
frame and the indication to check the
electrical installation on site.
- Remote resetting remains enabled.
5
≤ 1 day
7
≤ 7 days
15
≤ 30 days
Selector AUTO / MAN:
. Enables and disables the remote command of the Stop&Go.
. Possible states:
- AUTO: allows to remotely control the
Stop&Go via the Smartphone app (reclosing of
the associated device following a fault).
- MAN: on-site manual control only by the
handle of the Stop&Go (isolating and power
handles together)
Note: in case of on-site maintenance, to put the selector on MAN is
not enough. The use of a padlock is the only secured way
4. PREPARATION - CONNECTION (continued)
Stop&Go signalling led:
Possible states:
Led colour
State
Meaning
red
Fast blinking
Waiting for manual or remote
reset command following a
temporary fault (non-permanent)
If the Stop&Go detects a too
recurrent fault, remote actuation is
disabled
Steady
“Unwanted tripping”: Stop&Go has
detected a permanent default in
the system
Remote actuation is disabled
green
Fast blinking
Stop&Go in MAN mode
Steady
“Normal situation”: associated
device is powered and Stop&Go in
AUTO mode.
Switched-off
Stop&Go not supplied or sliding
front face downward
Wi-Fi module signalling led:
. Power led: indicates the status of operation of the interface:
-Steady green →interface supplied
-Steady off →interface not supplied
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016

8/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
4. PREPARATION - CONNECTION (continued)
Wi-Fi module signalling led (continued):
.Wi-Fi led: indicates the status of the Wi-Fi Network:
Possible states:
Led colour
State
Meaning
red
Slow blinking
No Wi-Fi- network detected or
connection problems
Fast blinking
(pressing the
multifunction button
longer than 30 sec.)
Total reset
[any firmware updates are
preserved]
Steady
Wi-Fi signal ≤ 25%
green
Slow blinking
Scanning for Wi-Fi network
(during association procedure)
Fast blinking
Programming via WPS button
of the Wi-Fi router
Steady
Wi-Fi signal ≥ 50%
orange
Slow blinking
Interface not associated to any
network (Factory configuration)
Fast blinking
Manual Programming mode
Steady
Wi-Fi signal between 25% and
50%
Wi-Fi module front face button:
. It is used to put the Wi-Fi interface in programming mode or to
restore factory settings:
Possible states:
Pressing time
Action
t ≈ 3 sec.
Wi-Fi interface put in configuration mode via
WPS button
t ≈ 7 sec.
Wi-Fi interface put in configuration mode via
“Manual procedure”
t > 30 sec.
Wi-Fi interface total reset
[any firmware updates are preserved]
4. PREPARATION - CONNECTION (continued):
Power supply module signalling led:
. Indicates the status of operation of the supplier:
-Steady green →system OK
-Steady off →supplier malfunctioning
Labelling:
. Circuit identification by way of a label inserted in the label holder
situated on the front of the Stop&Go and of the Power supplier.
5. GENERAL CHARACTERISTICS
Stop&Go marking:
. Front side marking: by permanent pad printing
Terminals marking:
. Upstream terminal-block: by permanent ink pad printing.
. Downstream terminal-block: by permanent ink pad printing.
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016
Red arrow to indicate that the front face of
the device can be put down
“ELIOT product” symbol
AUTO/MAN Selector

9/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
5. GENERAL CHARACTERISTICS (continued)
Stop&Go marking (continued) :
. Lateral side marking: by laser.
left side
right side
5. GENERAL CHARACTERISTICS (continued)
Supply module marking:
. Front side marking: by permanent ink pad printing (red line) and
laser marking
. Lateral side marking: by laser.
left side: Standard and programming information
right side: cabling and traceability information
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016
Alarm contact:
- IEC/EN 60950-1
- 230V~, 0,2A
- 24 / 48V, 1A
Association scheme
Wiring diagram
Standards
Legrand address
Operating range of
the supplier
Wiring diagram
Traceability information
Supply connection
with supply patch
cords
Cabling information
Function icon

10/16
ELIOT Kit STOP&GO Connected
Cat. N°: 4 149 54
5. GENERAL CHARACTERISTICS (continued)
Wi-Fi module marking:
. Front side marking: by permanent ink pad printing (red line) and
laser marking
. Lateral side marking: by laser.
left side: Standard and programming information
right side: cabling and traceability information
5. GENERAL CHARACTERISTICS (continued)
Wi-Fi Interface Radio-Frequency characteristics:
. Supported frequencies:
Min
Max.
Channel
1
11
Frequency
2412 MHz
2462 MHz
. Supported modulations
Standard
Supported bit rates (Mbps)
802.11b
1 - 2 - 5,5 - 11
802.11g
6 - 9 - 12 - 18 - 24 - 36 - 48 - 54
802.11n, HT,
20MHz, 800ns
6,5 - 13 - 19,5 - 26 - 39 - 52 - 58,5 - 65
802.11n, HT,
20MHz, 400ns
7,2 - 14,4 - 21,7 - 28,9 - 43,3 -
57,8 - 65 - 72,2
. Transmitter output power at maximum setting (antenna gain
included)
Modulation type
Measurement type
Value (dBm)
802.11b (1Mbps)
RMS
+18,2
802.11g (54Mbps)
RMS
+16,2
802.11n (72.2Mbps)
RMS
+16,2
Characteristics of the fault detection:
. Rd0 (non-operating rated resistance between the live parts and the
earth): 50 kΩ
. Rd (operating rated resistance between the live parts and the
earth): 100 kΩ
. Rcc0 (non-operating rated resistance between the live parts): 1,5 Ω
. Rcc (operating rated resistance between the live parts): 2,5 Ω
. The Stop&Go device can be used in TT and TN earth systems
Impulse withstand voltage:
. Uimp: 4 kV
Insulation rated voltage:
. Ui: 400 V
Pollution degree:
. 2 according to IEC/EN 60664-1.
Overvoltage category:
. III
Dielectric strength:
. 2500 V
Mechanical endurance of Stop&Go:
. 20000 operations.
Electrical endurance of Stop&Go:
. In accordance with the requirements of the standards of the
associated protection device.
Technical data sheet: F02465EN/01
Updated: 28/03/2019
Created: 06/10/2016
Legrand address
“ELIOT product” symbol
Function icon
Traceability information