LEGRAND Tynetec ZXT426 User manual

DocNo.FM0460issueJPage1
169MHzTelecareDevices
TemperatureExtremeSensor

__________________________________________________________________________________________________________


CompatiblewithReachat‐homealarms,Adventxtwardencall,
AltecResponseandTouchsafeProNursecallsystems
Solidstatetemperaturesensingelement
Loweralarmtemperature:5oC+/‐2.5oCfor30/60minutes
Upperalarmtemperature:30oC+/‐2.5oCfor5/10minutes
Rateofrisealarmtemperature:8oCperminute
Userreplaceable3.6VAALithiumbattery
Lowbatterywarning
Testbutton
Dimensions:84x84x36mm(HxWxD)
Weight:102grams
ProductCode:ZXT426


WhatareTemperatureExtremeSensorsusedfor?

Thetemperatureextremesensorwillprovideearlywarningofextremeloworhighhouseholdtemperatureswhichcouldresultin
theoccupiersufferinghypothermiaordehydration.Inaddition,thebuildingwillalsobeprotectedagainstburstpipesorpotential
firehazards.

WhereshouldTemperatureExtremeSensorsbefitted?

Thetemperatureextremesensorshouldbefittedinthehallwayorlivingroom.
Itshouldbewallmountedataround1.4metresabovefloorlevelandawayfromanydraughtsorheatsources.

TypicalToolsRequired

Adrillandscrewdriverarenotrequirediftheselfadhesivepadisused.
Alwaysmakesurethecorrectdrillbitsandscrewdriversareused.

Installation–UsingScrewFixings

1. Removethetopbypullingapartfromthebacksection.

2. Drillthebacksectionasrequiredandfixtothewallusing
thescrews&plugsprovided.

3. SettheDILswitches&links,fitthebatteryandtestas
describedonthefollowingpagebeforerefittingthetopsection.


Installation–UsingSelfAdhesivePads

1.Removethetopbypullingapartfromthebacksection.

2. Selectthebestlocationwherethewallisclean,dryandeven.

3. Sticktheadhesivepadtotherearfaceofthebacksectionand
pressfirmlytothewallensuringitisstucksecurely.

4. SettheDILswitchesandlinks,fitthebatteryandtestas
describedonthefollowingpagebeforerefittingthetop.












PULLAPART
TOREMOVE
TOP
SECTION
FIXBACK
SECTIONTO
WALL
Tynetec andAidcallare businessunitsofLegrandElectricLtd
Unit10CowleyRoad,BlythRiversideBusinessPark,Blyth
Northumberland,NE245TF.Tel:01670352371Fax:01670362807
Email:[email protected]Web:www.tynetec.co.uk

DocNo.FM0460issueJPage2
DILSwitchSettings

SetDILswitch1ONforMode1;
LowTemperatureAlarm=lessthan5oC+/‐2.5oCfor30minutes
HighTemperatureAlarm=greaterthan30oC+/‐2.5oCfor5minutes

SetDILswitch1OFFforMode2;
LowTemperatureAlarm=lessthan5oC+/‐2.5oCfor60minutes
HighTemperatureAlarm=greaterthan30oC+/‐2.5oCfor10minutes

SetDILswitch2OFFfor169MHztransmitterfrequency


LinkSettings

LK1–notused
SetLK2&LK3bothinposition“B”


FittingtheBattery

Onlyusethe3.7VAALithiumbatterysupplied.
Takecaretoensurethebatteryisfittedcorrectly,fitwiththered“+”endtotherighthandsideasshownabove.


Testing&RegisteringtheTemperatureExtremeSensor

TheTESTbuttonmustbepressedwhenlearningthetemperatureextreme
sensorontothewardencallsystem,at‐homealarmorNursecallsystem. 

Seethefollowingpagesforhowtoputeachofthese
productsinto“LearnMode”.

PressandholdtheTESTbuttonforabout3secondsuntil
theREDlightstartstoflash.

After9flashestherewillbea10secondpausefollowedby
another9flashes(thesensortransmitsahightemperature
signalfollowedbyalowtemperaturesignal).

RemovethebatterytoEXITTESTMODE
LeaveforafewsecondsthenrefitforNORMALOPERATION.

Therangeofallradiodevicescanbeaffectedbytheworkingenvironment‐alwaystakecareduringinstallationand
performseveraltestcalls.


Cleaning&Care

Temperatureextremesensorsshouldbecleanedperiodically.
Usethenozzleattachmentonavacuumcleanertoremovedust,insectsandcobwebsfromthecoverslots.
Thecasecanbewipedcleanwithadampcloth,neverusedetergentsorpolishetc.



Decorating

Neverpaintthetemperatureextremesensoritself.
Itisnotsusceptibletocontaminationfrompaintfumesthereforeno
specialprecautionsneedtobetaken.


BatteryLife

Thetemperatureextremesensorbatteryischeckedonceaday,ifthevoltagefallsandstaysbelowapresetlevelfor7consecutive
daysalowbatteryalertisautomaticallytransmitted.Oncealowbatterycallisreceivedthebatteryshouldbereplacedwithin7
days.DetailedinformationonbatterymanagementforallTynetec/Aidcallproductsisavailable‐requestDocNo.FM0630.








LINK
SETTINGS
DIL
SWITCH
SETTINGS
FITBATTERYASSHOWN
REDLIGHT
TESTBUTTON

DocNo.FM0460issueJPage3
RegisteringaTemperatureExtremeSensorontoaReachat‐homealarmunit

1.PuttheReachunitintoradiodevicelearnmode…

     









2.Activatethetemperatureextremesensor…


  









3.Exitradiodevicelearnmode…


     









4.CheckwiththeControlCentrethatitisconvenienttoperformatestcall,presstheTESTbuttonandconfirmtheyreceiveahigh
temperaturealarmcallfollowedbyalowtemperaturealarmcall.Remembertoremoveandrefitthebatteryafterthetestcall.


DeletingaTemperatureExtremeSensorfromaReachat‐homealarmunit

Enter1670usingthekeypadontherearoftheReachunit–thefrontlightwillFLASHFASTGREENandtheunitwillannounce
“ProgramMode‐Ready”.
Enter#041andtheReachwillannounce“DeleteRadioDevice”followedbya“Beep”.
Enter41(hightemperature)followedbythe6digitsensorIDtobedeletedandwaitforthe“Beep”
Enter42(lowtemperature)followedbythe6digitsensorIDtobedeleted,afterthe“Beep”press#toexit.
PressthekeytoexitProgramMode;theunitwillsounda“Double‐Beep”andthefrontlightwillreturntoSTEADYGREEN.


The6digitIDcanbefoundonalabelonthebackofthetemperatureextremesensor.





TheinstructionsgivenaboveforthestandardReachproductalsoappliestotheReachPlus,ReachPlusGSM
andReachUltramodels.Refertotheinstructionbookletsprovidedwiththeseproductsformoreinformation
onprogrammingandtestingradiodevices.












“Trigger
Radio
Device”
PressandHOLDtheGREENbuttonontheReachunit.

WhenthefrontlightFLASHESFASTGREENreleasethe
buttonandtheReachwillannounce“TriggerRadioDevice”.

Younowhave1minutetoactivatethetemperatureextreme
sensor.

PresstheGREENbuttonontheReachunit.

ThefrontlightwillreturntoSTEADYGREENandtheReach
isbackinnormaloperatingmode.

PressandholdtheTESTbuttonforabout3secondsuntilthe
REDlightstartstoflashandtheReachwillannounce
“HighTemperature”.

WhentheREDlightstopsflashingwaitforabout10seconds
anditwillstartflashingagainandtheReachwillannounce
“LowTemperature”.

IMPORTANT:removethebatterytoEXITTESTMODE,leave
forafewsecondsthenrefit.


DocNo.FM0460issueJPage4
RegisteringaTemperatureExtremeSensorontoanAdventxtwardencallsystem

1.PuttheAdventxtsystemintoradiodevicelearnmode…
 
     
 












2.Activatethetemperatureextremesensor…


  













3.ExittheAdventxtsystemradiodevicelearnmode…















4.PresstheTESTbuttonandcheckahightemperaturealarmcallisreportedonthewardencallsystemfollowedbyalow
temperaturealarmcallabout20secondslater.Remembertoremoveandrefitthebatteryafterthetestcall.


DeletingaTemperatureExtremeSensorfromanAdventxtwardencallsystem

PresstheLINEkeyandwaitforthe“Ready”prompt.
Enter5001followedbythekey.
Entertheflatnumberthetemperatureextremesensorisbeingdeletedfromfollowedbythekey.
PressTESTbuttononthetemperatureextremesensortobedeleted.
Waitforthe“PendantDisabled–EnterFlat”prompt.
Waitforabout20secondsforthesecond“PendantDisabled–EnterFlat”prompt.
Pressthe#keyandwaitforthe“Ready”prompt,thenpresstheLINEkeytocleartheconnection.





RefertotheAdventxtoperatorsmanual(DocNo.FM0420)providedwiththewardencallsystemformore
informationonprogrammingandtestingradiodevices.





UsingtheManager’sDECTtelephone;

PresstheLINEkeyandwaitforthe“Ready”prompt.

Enter5000followedbythekey.

Entertheflatnumberthetemperatureextremesensorisbeinginstalled
infollowedbythekey.

Younowhave1minutetoactivatethetemperatureextremesensor.

“Ready”
UsingtheManager’sDECTtelephone;

Pressthe#keyandwaitforthe“Ready”prompt.

PresstheLINEkeytocleartheconnectionandthewardencallsystemis
nowbackinnormaloperatingmode.

PressandholdtheTESTbuttonforabout3secondsuntiltheRED
lightstartstoflash.

Waitforthe“EnterLocationCode”promptthenpress0
(nolocation)followedbythekey.

Waitforthe“PendantEnabled–EnterFlat”prompt.

Afterabout20secondsyouwillhearthe“EnterLocationCode”
promptagain‐press0(nolocation)followedbythekey.

Waitforthe“PendantEnabled–EnterFlat”prompt.

IMPORTANT:removethebatterytoEXITTESTMODE,leavefora
fewsecondsthenrefit.

“Ready”


DocNo.FM0460issueJPage5
RegisteringaTemperatureExtremeSensorontoanAltecResponselocalcareralarmunit

1.PuttheAltecResponseunitintoradiodevicelearnmode…


     
 











2.Activatethetemperatureextremesensor…


  








 




3.ExittheAltecResponseradiodevicelearnmode…















4.PresstheTESTbuttonandcheckahightemperaturealarmcallisreportedontheAltecResponseunitfollowedbyalow
temperaturealarmcallabout20secondslater.Remembertoremoveandrefitthebatteryafterthetestcall.


DeletingaTemperatureExtremeSensorfromanAltecResponselocalcareralarmunit

PressENTERtoactivatethewake‐updisplaythenENTERagaintodisplaythemainmenu
PressENTERtoselectRadioDevices
PressthekeytoselectDeleteDevicethenpressENTER
Thedisplaywillpromptyouto“TriggertheSensor”
PresstheTESTbuttononthetemperatureextremesensortobedeleted‐thedisplaywillshowhightempandits41xxxxxxID
IfthisisthedeviceyouactivatedpressthekeytoselectDeletethenpressENTER
Afterabout20secondsthedisplaywillshowthelowtempandits42xxxxxxID
IfthisisthedeviceyouactivatedpressthekeytoselectDeletethenpressENTER
Note:iftheIDisNOTthedeviceyouactivatedpresstheENTERkeytoselectRejectthentryagain
ToexitthemodeselectExitthenpresstheENTERkey.





RefertotheAltecResponseinstallationguide(DocNo.FM0548)providedwiththeportablealarmunitfor
moreinformationonprogrammingandtestingradiodevices.



PressandholdtheTESTbuttonforabout3secondsuntiltheREDlightstartstoflash.

ThedisplaywillshowHighTemperatureandits41xxxxxIDnumber.
ChecktheIDiscorrect,pressthekeytoselectAcceptthenpressENTER.
Note:ifanotherdevicehasbeenpicked‐uppressENTERtoRejectandtryagain.
ThedisplaywillshowFlat,usethe&keystochoosethedwellingtype.
PressthekeytoselectNo:000000thenpresstheENTERkey.
Usethe&keystoselecteachdigitoftheflatnumberandthe
&keystomovebetweendigitsthenpresstheENTERkey.
PresskeyseveraltimestoselectExitthenpresstheENTERkey.
Thedisplaywillpromptyouto“TriggertheSensor”again.

Afterabout20secondsthedisplaywillshowLowTemperatureandits42xxxxxID
number,repeatasabove.

IMPORTANT:removethebatterytoEXITTESTMODE,leaveforafewsecondsthenrefit.
PressENTERtoactivatethewake‐updisplaythenENTERagaintodisplay
themainmenu.

PressENTERtoselectRadioDevices

PressENTERtoselectLearnDevice

Thedisplaywillpromptyouto“TriggertheSensor”.

Younowhave20secondstoactivatethetemperatureextremesensor.
FromtheLearnDevicemenuselectExitthenpressENTER.

FromtheRadioDevicesmenuselectExitthenpressENTER.

Thedisplaywillreturntothewake‐upscreenandgoblankafter10seconds.

TheAltecResponseisnowbackinnormaloperatingmode.

tynetec
tynetec


DocNo.FM0460issueJPage6
RegisteringaTemperatureExtremeSensorontoaTouchsafeProNursecallsystem

1.PuttheTouchsafeProMasterPanelintoTelecareregistrationmode;touchthescreenandLogonasanEngineeroraManager
(passwordrequired),thenfromthemainmenupagetouchtheTelecarebuttontoopenthescreenshownbelow…























2.Enterthetemperatureextremesensor8digitID’s…











3.PresstheClosebuttontoexitTelecaremodeandtheNursecallpanelisnowbackinnormaloperatingmode.

4.PresstheTESTbuttonandcheckahightemperaturealarmcallisdisplayedontheNursecallpanellikebelowfollowedbyalow
temperaturealarmcallabout20secondslater.Remembertoremoveandrefitthebatteryafterthetestcall.










Thescreenbannerisredforhigh/lowtempalarmcalls(Touchthebannertodisplaynotes).
Ahighorlowtemperaturealarmcallcannotbeacceptedorsilencedfromthescreen.
YoumustvisittheappropriateNursecallCallPointtocancelthecall.

DeletingaTemperatureExtremeSensorfromaTouchsafeProNursecallsystem

SelectthehightemperaturesensorIDtobedeletedfromtheDeleteTelecareDevicepull‐downlistbox(prefixed“T41”).
DetailsofthesensorselectedwillbedisplayedintheRoom,HouseCodeandIDboxesbelow.
IfthedetailsshownarecorrectpresstheDeletebutton.
SelectthelowtemperaturesensorIDtobedeletedfromtheDeleteTelecareDevicepull‐downlistbox(prefixed“T42”)
RepeatasaboveandpresstheClosebuttontoexit.




RefertotheTouchsafeProDisplayPaneluserguide(DocNo.FM5505)providedwiththeNursecallsystemfor
moreinformation.



TynetecandAidcalloperateapolicyofcontinuousimprovementandreservetherighttochangeproductspecificationswithoutnotice.
IfanyvariationtothedetailscontainedinthisdocumentaresuspectedpleasecontactTynetec’scustomersupportdepton01670352371.
The8digitID’saremadeupofthe2digitdevicetypecode(HighTemp=41&LowTemp=42)
followedbythe6digitunitIDwhichcanbefoundonalabelonthebackofthesensor.

TouchtheAddTelecareDeviceboxthenusetheon‐screenkeypadtoenterthehightempID.

Hint:enterazoneintheFilterboxtonarrowthesearchfortheroom(seebelow).

SelecttheusersCallPointIDfromtheRoompull‐downlistboxthenpressSave.
Note:thisistheroomunitthatwillbewillbeusedtocancelthecall.

TouchtheAddTelecareDeviceboxagainandrepeatasabovebutthistimeenterthelow
tempIDi.e.42followedbythesame6digitIDfromthelabel.
Usekeypadtoenter
8digitID’s*here
Selecttherelevant
CallPointIDhere
Savewhendone
Closetoexitmode
On‐screenkeypad
CALLING
CANCEL
HC345ID001
PresstheLIGHTGREY
buttontocancelthecall
*Note:bothhighandlow
temperatureID’smust
beentered;
Prefix41=HighTemp
andPrefix42=LowTemp
ZXT426W66265
Ser:10151997
ID:037233
EE1770V1.05A
DR
