LEGRAND SANUS ELITE BLFS420 User manual

BLFS420
INSTRUCTION MANUAL
WE’RE HERE TO HELP
Our live US-based install
experts are standing by to help.
Call us at:
US: [phone]
Get it right the first time.
HeightFinder™ shows you
where to drill.
Use it now:
SANUS.com/1172
Want to watch a video that
shows how easy this is?
Watch it now at:
SANUS.com/3115
Texto en español, página 10

2
IMPORTANT SAFETY INSTRUCTIONS
– PLEASE READ MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed ONLY to be installed into wood studs, solid concrete or concrete block
—DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV
●This product is designed for INDOOR USE ONLY
●The wall must be capable of supporting five times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service.
Call Customer Service
1-800-359-5520 Call Customer Service
1-800-359-5520
Wall
Construction
ONLY install on
these acceptable
wall types. Drywall alone
will NOT hold the
weight of your TV.
Unsure
wood studs Solid concrete or
concrete block
ACCEPTABLE
Concrete anchors Required
(NOT INCLUDED)
CAUTION:
DO NOT install
in drywall alone
125 lbs.
(56.6 kg)
TV Weight Limit
(including accessories)
DO NOT EXCEED
If your TV (plus accessories) weighs MORE, this
mount is NOT compatible.
Visit SANUS.com or call customer service to find a
compatible mount.
Tools Needed
Wood Stud Install
Concrete Install
Awl
Pencil Level Tape
Stud
Finder
ScrewdriverTape
Measure
7/32 in.
(5.5 mm)
Wood
Drill Bit
Electric
Drill
Hammer
1/2 in.
( 13 mm)
Socket
Wrench
Drill Bit
3/8 in.
(10 mm)
Concrete

3
Dimensions
BEFORE YOU BEGIN
Remove the stand
from your TV —if attached.
Install any accessories
you may have purchased, if they requireTV
removal prior to assembly. The TV is removable
for future accessory purchases.
Soft clean surface
Protect the face
of your TV when laying it down for
installation.

4
1/4-20 x 1 in.
2.5mm
M6 x 25mmM6 x 12mm
5mm
10-32 x 3/8 in.
10-24 x 1/2 in.
M8 x 50mm
M8 x 16mm M8 x 20mm
M8 x 30mm
M8 x 40mm
3/16 in.
5/16 x 3 ½ in.
Washers
(qty. 4)
03
02
01
M6/M8
M6
M8
05
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do
not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
Supplied Parts and Hardware
TV Screws (qty. 4 each)
[Only one size fits your TV]
Spacers
(qty. 4 each)
TV Bracket
Vertical
TV Bracket
Horizonal
10-32 x 5/16 in. TV Interface Assembly
06
(qty. 2)
04
STEP 3
STEP 1
Concrete Anchor
Arm Assembly
CAUTION: Do not use in drywall or wood.
Custom Wall Plate Screw Ball End Hex Key
12 13
07
08
Locking Screw
Lag Bolt
Drilling Template
Wall Plate
09
15
11
For concrete installations ONLY
(qty. 1)
(qty. 1) (qty. 4)
(qty. 2) (qty. 1) (qty. 1)
(qty. 1)
STEP 2
C1
Concrete Anchors
are NOT INCLUDED
Contact Customer
Service to inquire
about the
concrete anchors.
NOTE: Not all hardware included will be used.
Lag Bolt Washer
10
(qty. 4) (qty. 4)
(qty. 1)
(qty. 4)
14
(qty. 1)
Locking Washer
M6 x 13mm
2.5mm
22mm
M6 x 20mmM6 x 12mm
M4 x 12mm
M6 x 35mm
M4 x 35mm
M5 x 11mm
5mm
10-32 x 5/16 in.
M8 x 50mm
M8 x 16mm
M8 x 20mm
M8 x 30mm
M8 x 40mm
3/16 in.
5/16 x 2¾ in.
5/16 in.

5
• Flat Back TV
[TV bracket s lay flat on your TV]
NO SPACER SPACER NEEDED
AB
Only one screw size fits your TV.
M6 M8
01
Use short TV screws 01 .
Spacers 03 not needed.
STEP 1 Attach TV Brackets to TV
Use long TV screws 01 and spacers 03 to create extra space
between the TV and TV bracket.
• Flat Back TV with extra space needed
[for deep inset holes or cable interference]
• Rounded or Irregular Back TV
[TV brackets NOT resting flat on your TV]
CAUTION: Verify adequate thread engagement with your screw 01 , washer 02 ,
spacer 03 combination AND TV bracket 04 .
— Too short will not hold your TV. — Too long will damage your TV.
1.2 Select TV Screw Length and Spacers1.1 Select TV Screw Diameter
NOTE: If your TV
included inset spacers or
adapters, use them UNDER
the mount hardware.
1.3 Attach TV Brackets to Your TV
CAUTION: Avoid potential personal injuries and property damage! DO NOT use power tools for this step. Tighten the screws 06 only enough to secure the TV brackets to the TV.
02
01
ANO SPACER
12
06
05
02
01
BSPACER NEEDED
03
01
02
04
04

6
STEP 2A Attach Wall Plate
CAUTION: Avoid potential personal injury or property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1½ x 3½ in. (38 x 89 mm)
●Minimum spacing between studs: 16 in. (406mm)
●Stud center must be verified
Wood Stud Installation
12
Min.
16 in.
(406 mm)
Max.
5/8 in. (16 mm)
07
09
3 4
2  in. (7 cm)
7/32 in.
(5.5 mm)
07
08
IMPORTANT: Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth of 2  in. (7 cm), using a 7/32
in. (5.5 mm) diameter drill bit.
CAUTION: Avoid potential personal injury or property damage!
Improper use could reduce the holding power of the lag bolt 09 .
Tighten the lag bolts 09 and lag washers 10 only until they are
pulled FIRMLY against the wall plate 08 .
DO NOT over-tighten the lag bolts 09 . Go to STEP 3 on PAGE 8.
10

7
CAUTION: Avoid potential personal injury or property damage!
●Mount wall plate
08
directly onto concrete surface (no wall covering)
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
●Minimum spacing between lag bolts is 16 in.
●For concrete applications, arm assembly
11
(STEP 3) must remain centered in wall plate
08
.
Keep this in mind when selecting wall plate location
Solid Concrete or Concrete Block Installation
STEP 2B Attach Wall Plate
Concrete Anchors are not included
Contact Customer Service at 1-800-359-5520
to inquire about the concrete anchors.
12
3/8 in.
(10 mm)
3 in. (8 cm)
002862.eps
07 07
34
CAUTION: Be sure the anchors C1 are seated flush with the
concrete surface.
CAUTION: Never drill into the mortar between blocks.
08
CAUTION: Avoid potential personal injury or property damage!
Improper use could reduce the holding power of the lag bolt 09 .
Tighten the lag bolts 09 and lag washers 10 only until they are
pulled FIRMLY against the wall plate 08 .
DO NOT over-tighten the lag bolts 09 .
C1
Concrete achors (Fischer UX10 x 60R) C1 available through Customer Service.
09
10

8
15
3.1 Attach Arm Assembly to Wall Plate
STEP 3 Hang TV onto Wall Plate
12
05
11
05
3.2 Attach TV to Arm Assembly
HEAVY! You may need assistance with this step.
HEAVY! You may need assistance with this step.
11
11
CAUTION: Avoid potential
injuries or property damage!
Locking screw 13 and washer
14 MUST be installed to secure
the TV mount and the arm assembly.
13
14 15
1
NOTE: For WOOD STUD APPLICATIONS,the arm assembly 11 can be
slid anywhere along wall plate 08 for optimal positioning of your TV.
08
2
11
08
CAUTION: Avoid potential personal injury or property damage!
For CONCRETE
APPLICATIONS:
The arm assembly 11
MUST remain centered
in wall plate 08 .
08
11
34
65
S
12
12
15
15

9
1
1. IMPORTANT: Fully extend arm assembly 11 to
ensure enough slack in cables.
2. Route your cables through the arm assembly 11 as
shown.
2
Manage Cables
Your TV should adjust easily when moved, then
stay in place. If your TV is too loose or too tight use
the hex key 15 for additional tightening of the
right and left tilt tension screws T.
1. Loosen
security
screw 13 .
3. Retighten
security
screw 13 .
2. Level TV.
13
TILT ADJUSTMENT
LEVEL ADJUSTMENT
TV Adjustments
1. Remove your TV (PAGE 9).
2. Open the cover plates, remove two screws 12 , and loosen
screws at bottom of arm Sto release arm assembly 11 .
3. Reposition the arm assembly 11 on the wall plate (STEP 3.1).
4. Reattach the two screws 12 (STEP 3.1), tigthen the screws at
the bottom of arm S, and close the cover plates.
5. Hang your TV onto the arm assembly 11 following STEP 3.2.
12
12
08
11
08
11
LATERAL SHIFT
REMOVING THE TV
15
HEAVY! You may need assistance with this step.
HEAVY! You may need assistance with this step.
CAUTION: Avoid potential injuries or property damage!
Do NOT adjust the arm position from center for concrete
applications. Arm 11 MUST remain centered in wall plate
08 for all concrete applications!
1 2 3 4
14
15
11
T15
T
15 13 15
REMOVING THE ARM
12
11
08
12
15
15
15
13
08
Locking screw 13
MUST be installed to
secure the TV mount
and the arm assembly.
S
15
S

10
INSTRUCCIONES IMPORTANTES DE SEGURIDAD:
GUARDE ESTAS INSTRUCCIONES Y LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO.
No — ¡Perfecto!
Sí — Este soporte NO es compatible. Visite MountFinder.Sanus.com o llame al : [US]: [phone]
[EMEA]: [phone] [Reino Unido]: [phone] para encontrar un soporte compatible.
Lea atentamente estas instrucciones para asegurarse de que está familiarizado con el sencillo proceso de instalación.
Consulte igualmente el manual de su televisor para conocer si existen requisitos especiales para el montaje de su aparato.
Si no entiende las instrucciones o si tiene dudas acerca de la seguridad de la instalación, el montaje o el uso del producto, póngase en
contacto con el servicio de atención al cliente o llame a nuestro servicio técnico.
¿Tiene todas las
herramientas
necesarias?
Antes de empezar, asegúrese de que este es el soporte adecuado para usted.
1
2
3
4
¿De qué está
hecha la pared?
PRECAUCIÓN: Evite posibles lesiones personales y daños materiales.
●Este producto se ha diseñado para usarse en montantes de madera, hormigón macizo y paredes de bloques de hormigón:
NOloinstale en paredes únicamente de yeso
●La pared debe ser capaz de soportar hasta cinco veces el peso combinado del televisor y el soporte
●No utilice este producto para ningún otro propósito que no sea el especificado explícitamente por el fabricante
●El fabricante no se responsabiliza de ningún daño o lesión resultante del montaje incorrecto o el uso indebido del producto
¿Preparado para
empezar?
PRECAUCIÓN:
NO instalar en
paredes de yeso solo
Antes de comenzar
ESTAMOS A SU DISPOSICIÓN PARA AYUDARLE
Retire el soporte de su televisor... ¡si ya estaba instalado, claro!
Instale cualquier accesorio que quiera añadir a su televisor.
Consulte todos los manuales de instalación de los accesorios para determinar si necesita INSTALARLOS ANTES de montar su televisor.
Proteja la pantalla de su televisor cuando lo tumbe para la instalación.
¿Desea ver un vídeo que muestra lo fácil que será este proyecto de bricolaje? Puede verlo en: SANUS.com/3119
Acierte a la primera. HeightFinder™ indica el lugar donde debe taladrar. Descúbralo en: SANUS.com/2567
Nuestros expertos instaladores en EE. UU. están a su disposición para ayudarle. Llámenos al:
[US]: [phone] [EMEA]: [phone] [UK]:[phone]
¿Su televisor pesa
(accesorios incluidos)
MÁS de 56,6 kg
(125 lbs)?
56,6 kg
(125 lbs)
Lápiz Nivel DestornilladorCinta métrica Taladro eléctrico Llave de tubo
Instalación sobre
montante de madera
Instalación sobre
hormigón
Punzón
Localizador de
montantes
5,5 mm
(7/32 pulg.)
Broca para
madera Martillo
13 mm
(1/2 pulg.)
Broca para
hormigón
10 mm
(3/8 pulg.)
Solo se adapta a su televisor un tamaño de tornillo.
• Televisor con parte posterior plana [los soportes del televisor se apoyan planos sobre su televisor]
SIN ESPACIADOR
ESPACIADOR NECESARIO
• Televisor con parte posterior plana que necesita espacio extra [para agujeros profundos o interferencia de cables]
• Televisor con parte posterior redondeada o irregular [los soportes de televisor NO se apoyan completamente planos en su televisor]
A
Utilice tornillos de televisor cortos 01 .No es necesario usar 03 espaciadores.
Use tornillos de televisor 01 largos y espaciadores 03 para crear espacio extra entre el televisor y el soporte del televisor.
1.2 Seleccione la longitud de los tornillos y los espaciadores del televisor
1.1 Seleccione el diámetro de los tornillos del televisor
1.3 Monte el soporte del televisor
B
ESPAÑOL
Cómo acoplar el soporte al televisorPASO 1
ADVERTENCIA: Este producto contiene piezas pequeñas que, en caso de ser tragadas, podrían causar asfixia. Antes de comenzar a montar la unidad, verifique que dispone de todas las piezas yque se encuentran en
buen estado. Si no dispone de todas las piezas o alguna está dañada, no devuelva el elemento defectuoso al distribuidor. Póngase en contacto con el servicio de atención al cliente. Nunca utilice piezas en mal estado.
NOTA: No se utilizarán todos los elementos de sujeción incluidos.
PÁGINA 5
Dimensiones PÁGINA 3
¿Paneles de yeso con
montantes demadera?
¡Perfecto!
¿No está
seguro?
¿Hormigón macizo o
bloque de hormigón?
Llame al servicio de atención al cliente:
[US]: [phone] [EMEA]: [phone] [Reino Unido]:[phone]
Se requiere el kit CMK1
[no está incluido]
Piezas y accesorios suministrados
PÁGINA 4
PRECAUCIÓN: Evite posibles lesiones personales y daños materiales. NO use herramientas eléctricas para este paso. Apriete los tornillos 01 y 06 con la fuerza adecuada para fijar el soporte del televisor. NO los apriete demasiado.