Leister Airpack User manual

1
LEISTER AIRPACK
High Pressure Blower
Please read operating instructions carefully
before use and keep for further reference.
GB
OPERATING INSTRUCTIONS
• The LEISTER High Pressure Blower AIRPACK is suitable for building into machines,
installations and appliances and is designed for maintenance-free continuous
operation.
•It is suitable for delivering air in non explosive zones, for non combustible,
non corrosive and non explosive gases.
• Air supply for LEISTER Hot-Air Tools, for intake air supply and for cooling.
• Ventilation of tanks, aquariums and different applications for textile machines.
• Drawing off of welding gases and fumes.
• Transfer of granular and loose materials.
• Vacuuming for silk screen printing machines and air tables.
APPLICATION
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. [phone] Fax [phone] www.leister.com [email protected]
®

Electric shock! Disconnect any pole of the tool from
line/mains before opening it as live components and
connections are exposed.
The tool must be grounded/earthed by using a protec-
tive conductor.
The voltage rating stated on the tool must correspond
to the line/mains voltage. The blower should only be
connected and operated by qualified staff.
Fire hazard! The blower’s surface temperatures can
exceed 80°C. Do not let anything get in contact with it
or connect any parts to it.
Protect the tool from damp and wet.
Use a protective motor switch.
Pay attention to the direction of rotation.
230
400
2
WARNING
CAUTION
100 Pa = 1 mbar
Power consumption kW
Voltage rating (+/– 10 %)V~
Current rating A
Frequency Hz
Max. Airflow l/min.
Static Pressure Pa
Noise emission level LpA (dB)
Environmental protection (IEC 529)
Diameter of air intake (external Ø) mm
Diameter of air outlet (external Ø) mm
Ambient temperature °C
Weight kg
Size (L x B x H) mm
2.2 2.2
Æ3´230 Y 3´400
95.2
50 60 50 60
3500 4100 3500 4100
24000 28 000 24000 28 000
73 73
IP 54 IP 54
ø 60 ø 60
ø 60 ø 60
<40 < 40
25 25
345 ´335 ´345 345 ´335 ´345
TECHNICAL DATA
Design Side channel compressor
APPROVAL MARKS

Conditions of operation
•The AIRPACK blower should be fixed to the installation stand (6) by using four
M12 screws. The tool can be installed horizontally or vertically.
•Protect the tool from vibration and shock.
Important: •The blower must not be operated with the air intake or outlet hose
connection blocked off. By throttling down the airflow, compression
heat will develop, which will cause the blower and air hose to heat
up. Use heat resistant or metal hose only. Connect the hose with
cable clamps to the flange (1).
•Operate the blower by using a protective motor switch only. Do
not exceed the rated current (see nameplate).
• Installation dimensions in mm
Operation
•The acceptable ambient and air intake temperatures are from – 15°C to + 40°C.
Ensure a good room ventilation.
•For use in a dusty environment, a LEISTER stainless steel filter (Order No.110.896)
should be fitted onto the air intake (2).
•The blower should be connected by qualified staff. Pay attention to the direction
of rotation! See arrow on the compressor housing (7).
•
The appropriate connections should be made in the connection box (4)
according to the voltage. Connect the protective conductor to the ground/
earth terminal, measure the ground/earth resistance.
Description of tool
1. Air outlet flange ø 60
2. Air intake flange ø 60
with integrated mesh
3. Motor
4. Electric connection box
5. Connection box lid
6. Installation stand
7. Compressor housing
7
4
6
1
3
2
3
OPERATION LEISTER AIRPACK High Pressure Blower
5
L1 L2 L3
Æ
L1 L2 L3
Y
220–254 V 380–440 V
W2
U1
U2
V1
V2
W1 U1 V1 W1
W2 U2 V2
Circuit diagram in
connection box lid (5)

4
BA AirPack/ 06.2001/GB
•Use only LEISTER accessories.
• Other voltages
•The stainless steel filter and mesh in the air intake flange (2) should be cleaned
when dirty, otherwise the motor (3) can overheat. The integrated mesh may
be removed for cleaning from the air intake flange (2) by unscrewing the two
M6 screws.
•Repairs should only be carried out by authorised LEISTER Service Centres.
They guarantee a specialised and reliable Repair Service within 24 hours using
original spare parts lists.
•Guarantee and liability are in accordance with the guarantee certificate as
well as with the currently valid general business and sales conditions.
•LEISTER Process Technologies rejects any guarantee claims for tools which are
not in their original condition. The tools must never be altered or changed.
Technical data and specifications are subject to change without prior notice.
Your authorised Service Centre is:
GUARANTEE AND LIABILITY
SERVICE AND REPAIR
MAINTENANCE
SPECIAL VERSIONS
ACCESSORIES
®
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. [phone] Fax [phone] www.leister.com [email protected]