Leisure Concepts Smartop Upright 3.0 User manual

Installation Instructions - Updated as of 01/08/20
Page 1
Smartop Upright 3.0 200108
Upright 3.0
Figure 2
Figure 3
Step #1
Position the Smartop (in closed position) on the spa making sure that all four
corners are properly positioned and square on the spa.
Step #3
Note: The ball studs will be pre-installed in the hole closest to the back of the
bracket. If the cover doesn’t lift off the spa easily, start by moving one of the
ball studs on one side of the spa to the front hole and re-attach the shocks. If the
cover still doesn’t lift off the spa easily, move the ball stud on the other side of the
spa and re-attach the shocks.
Step #6
While pressing downward on the Smartop cover mounting bracket, swing the
Smartop cabinet mounting bracket up until it is parallel with the spa acrylic
and attach to the spa cabinet using the supplied #10 x 2” mounting screws
(see Fig. 4).
Step #7
Gently raise the Smartop into the upright position making sure to keep a firm
grip on the cover and attach the shocks to the ball studs (see Fig. 5). Note:
When attaching the shocks, make sure the black body of the shock is on top.
Step #5
Attach the Smartop 3.0 cabinet mounting bracket to the Smartop 3.0 cover
mounting bracket, in the bottom hole, using the supplied 3/8 x 2” button
head socket bolt, washer and locknut (see Fig. 4). Note: Make sure to use the
plastic spacers on either sides of the Smartop cabinet mounting bracket where
the bolt goes through.
Figure 1 EAS Bracket
EAS Handle
Button Head
Socket Bolt
Step #2
Attach the EAS handle to the EAS bracket using the supplied 5/16 x 1-1/4”
button head socket bolt (see Fig. 1).
J
K
Ball stud
B
Locknut
C
Washer
Locknut
Smartop
Cabinet
Mounting
Bracket
Figure 4
Button Head
Socket Bolt
F
G
E
Step #4
Insert the 3/8 x 2” button head socket bolt into the top hole in the back of
the Smartop cover mounting bracket. Make sure to install the rubber stop
on the button head socket bolt once you insert the bolt through the outside
flange of the Smartop cover mounting bracket. Secure the 3/8 washer and
locknut to the opposite end of the button head socket bolt (see Fig. 3). Note:
Do not overtighten locknut.
Washer
Locknut
Plastic
Spacers
Mounting
Screws
Button Head
Socket Bolt
F
G
E
LH
Rubber
Stop
I
Cover
Mounting
Bracket
A

Page 2
Figure 6
Sure Lock
Latch
Assembly
O
Self-Tapping
Screws
P
Side
of
Spa
Latch Catch
Smartop Upright 3.0 200108
ITEM PART# DESCRIPTION QTY
A(L) 101875 ST UPRIGHT 3.0 SPA MOUNTING BRACKET (L) 1
A(R) 101876 ST UPRIGHT 3.0 SPA MOUNTING BRACKET (R) 1
B 100244 5/16 BALL STUD 4
C 100032 5/16 NYLON LOCKNUT 4
D 100034 BLACK HEX DOME CAP 2
E 101749 3/8 X 2" BUTTON HEAD SOCKET BOLT - BLACK ZINC 4
F 100951 3/8 WASHER - BLACK ZINC 4
G 100838 3/8 LOCKNUT 4
H 101877 PLASTIC SPACER-3/8 X 1/8" 14
I 101885 RUBBER STOP - 1-1/8" 2
J 101596 EAS HANDLE 2
K 101751 5/16 X 1-1/4" BUTTON HEAD SOCKET BOLT - BLACK ZINC 2
L 100359 #10 X 2" PHILIPS PAN HEAD MOUNTING SCREW 20
M 100016 SMALL BLACK DOME CAPS 24
N
101796 101880-
101884
SHOCK 2
O 101871 SURE LOCK LATCH ASSEMBLY 2
P 101065 #8 X 3/4" PHILIPS FLAT HEAD SELF-TAPPING SCREW (BLACK ZINC) 8
Q 101078 LOCK 1
Step #7
Connect the Sure Lock latch to the latch catch. While puching down on the
Smartop, position the Sure Lock latch on the side of the spa and mark where
the latch base rests against the spa skirting. Attach the Sure Lock latch to
the spa skirting, where marked, using the supplied #8 x 3/4” self-tapping
screws (see Fig. 6).
Figure 5
Shock
N