Lena Lighting WSED414 HIM14 User manual

Stand-alone Dual Sense Motion Sensor TM
WSED414 (HIM14)
HF and PIR, Daylight harvest Control for lndependentDALI
Mechanical Structure
C - Surface box
B - Facia Cover
PIR
Photocell
LED indicator
56
Infrared receiver
HF Sensor module
ABlind
BBlind
Sensor mode selection
Rotary switchpreset
A - ControlBoard
Note:the blinds areoptional,theymay beinserted
behindthe lens for focussing the detection range.
Installation:
For more details, please refer to user manual.
1Directjunctionboxmounting Surfacemountassembly
2
Note:We recommend the mounting distance between sensor to sensor should be more than 2m to prevent sensors
from false-triggering.
Technical Data
InputCharacteristics
ModelNo. SensorData
HIM14
120~277VAC 50/60Hz
<1W
ModelNo.
Sensorprinciple
Operationfrequency
Transmissionpower
Sensormode
HIM14
Mainsvoltage HighFrequency(microwave),PIR
Stand-bypower 5.8GHz+/-75MHz(HF)
<0.2mW(HF)Switchedpower
Warming-up Max.20pcs devices,40mA
30s 4 modes:PIR,HF, PIR+HF,PIR/HF
Detectionrange
HIM14 Max.(Ox H)12mx6m
Max.(OxH)16mx 12m
SafetyandEMC
EMCstandard(EMC)
Safetystandard(LVD) EN55015, EN61000 HIM54(2lens)
Detectionangle Max.(Lx W x H)16mx 6mx12m
EN60669, AS/NZS60669 360°
EN300440,EN301489-1,
EN62479
RadioEquipment(RED)
Certi cation Environment
Semko, CB, CE, EMC, RED, RCM Operationtemperature
IPrating Ta: -20°C~+55°C
IP20
RED IP20
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 1/6

Dual Sense Introduction
 commonlyknownMicrowaveandInfraredaremaindetectingtechnologiesinlightingcontrols.Bothhavetheadvantageand
disadvantageforindustrialapplications.
Advantage Advantage
HF PIR
* sensitivetominormotion.
* sensitivetoradialmovement. * nopenetration,con neddetectionarea. * sensitivetotangentialmovement.
* can bere ectedbyobjectshencecoveringbigdetectionarea
* resilienttoheatsource,smokeandandairconditioner. * resilienttomotionobjectwhichhasnoheatradiation.
Disadvantage Disadvantage
* penetrateswalls, picksupmotionsoutsideoftheof cearea;
* back wave detection, falsetrigger bymotionsatthe back.
* can befalsetriggeredbyventilationfans,waterpipe,elevators
etc.inindustrialapplication.
* can befalsetriggeredbyairconditioner,smokeand
otherheatsources.
TheremedyistocreateDualSensebycombiningbothtechnologiestomakeuseoftheadvantageand bypassthedisadvantage.
4 optional detection modes via DIP switch or remote control:
* HF: Microwave only
* PIR:PIR modeonly
* HF+PIR:both PIRandmicrowavemode,todecreasethedetectioncapabilityanddetection 1 2
area.Onlywhenbothdetectionsare activated,themotionisconsideredvalid.Thisis
topreventthesensorfromfalsetriggerbyheatsource,airconditioner,ventilationfans,
waterpipeandelevatorsetc... I
II
III
IV
HF
PIR
HF+PIR
HF/PIR
* HF/PIR:either PIRormicrowavemode,toincreasethedetectioncapabilityanddetectionarea;
DetectionPattern
09
Intelligent
Photocell Ambientdaylight
threshold
One-Key
Commissioning RotarySwitch
Programing 15
Functions and Features
1 Daylight Harvest
Lightwill notswitchon
whennaturallightis
suf cient,even thereis
motiondetected.
Thelightswitcheson Thelightturnsonatfullordimstomaintainthe lux level. The lightoutput
regulatesaccrodingtothelevelofnaturallightavailable.
automaticallywith
presencewhennatural
lightisinsuf cient.
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 2/6

Note:
The Light automatically dims down and
eventually turns offif the natural light lux
level exceeds the daylight threshold.
However, if the stand-by period is preset
 xture never switches off
but dim to minimum level, even the
natural light is suf cient.
Thelightswitchesoff when
theambientnaturallightis
suf cient.
Thelightdimstostand-by
periodafterhold-timeand
staysonselectedminimum
dimminglevel.
Thelightswitchesoff
completelyafterthe
stand-byperiod.
Settings (Remote Control HRC-11)
ON/
OFF PermanentON/OFF function
Pressbuttontoselect permanentONorpermanentOFF mode.
* Press button toquitthismode.
ThemodewillchangetoAUTOModeafterpowerfailure.
Reset Settings
Pressbuttonall settingsgobacktorotaryswitchsettings.Sensordetection
modereturnstoDIPswitchsettings.
Shift Button
PressbuttontheLEDonthetopleftcornerwill ashtoindicatemode
selection.All values / settingsinREDarevalidfor 20seconds.
AUTO mode
Pressbuttontoinitiateautomaticmode.The sensorstartsworkingandall
settingsremainasbeforethelightisswitchedON/OFF.
& A
4h h4h
SEMI-AUTO mode
1.Pressbuttonthe redLED ashesforindication.
2.Pressbutton-toinitiatesemi-automode.The  xtureis
manuallyturnedonbypressingthepush-switch,andgoesoff automaticallyinthis
mode.(Absencedetectionmode) HRC-11
Poweroutput
Pressthebuttonstoselectlightoutputat80%(atinitial10,000hours)or100%.
 functions are disabled.
Brightness+/-
Pressthebuttonstoadjustthelightbrightnesstoresetthetargetluxlevel.
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 3/6

Scene program- 1-key commissioning
1.Pressbuttontoprogram.
2.Select the buttons in --by-bydimmingtosetall
parameters.
3.Pressbuttontosave all thesettingsprogrammed intheremotecontrol.
4.Pressbuttontosetthesettingstoeachsensorunit(s).
For example, toset detectionrange 100%, daylight threshold Disable, hold-time 5min, stand--by dimming level 30%, the steps should be:
 
settings are passed on the sensor(s).
Detectionrange
Pressbuttonsinzonetosetdetectionrangeat100%/75%/50%/10%.
Daylight threshold
PressbuttonsinzoneDaylighttosetdaylightsensor/targetlux level at50Lux/ 100Lux/ 300Lux/ 500Lux/ Disable.
Note: 2lux / 10lux are disabled.
To set daylight sensor at 100Lux / 300Lux /  rst.
Ambient daylight threshold
1.Pressbuttonthe redLEDstartsto ash.
2.Pressbutton the surroundingluxlevel issampledandsetasthenewdaylightthreshold/ targetlux level.
Hold-time
Pressbuttonsinzone-tosetthehold-timeat2s/30s/ 1min/ 5min/10min/ 15min/ 20min/ 30min.
Note: 1. To set hold-time at 30s / 5min / 15min /  rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exitfromTest mode,pressbuttonoranybuttonin-
Stand-by time (corridorfunction)
Pressbuttonsinzone-bytosetthe stand-byperiodat0s/ 10s/ 1min/ 5min/ 10min/ 30min/ 1h/ 
-level control, the  xture is 100%on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Stand-by dimming level
Pressthebuttoninzone-bydimming tosetthe stand-bydimminglevel at10%/ 20%/30%/ 50%.
Daylight harvest auto-conꢀ gurationfunction
1.Pressbuttonthe redLEDstartsto ash.
2.Select a timeperiodand thesensor will dolightlevel measurementand determine/savethe lowestlight level (commissionline)
with100%lighton, soastosetthetargetluxlevel automatically.
Note:1.Make sure the light level measurement covers the night time.
2.The  xture will gointo sensor modeafter the measurement, all sensor settings remain unchanged.
Dual tech & RF mode
1.Pressbuttonsinthiszonetoselectsensortechnology.
HF+PIR:thelightisonwhenbothHFandPIRsensorsareactivated.
HF/PIR:thelightisonwhenHForPIRsensorsareactivated.
2.Learn/ Erase,Transmit,RX100%andRXSTBY%aredisabled.
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 4/6

Rotary Switch Preset
Arotaryswitchisbuiltinsidethesensorforscene
selection/ fastprogramming.Total 16channels
areavailable: Detection
range Daylight sensor Stand-by
time Stand-by
dim level
Channel
0
Hold-time
5s
100% Disable 10s 10%
1
2
3
4
5
6
7
8
9
A
B
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
100%
1min 50Lux 5min
10min

10%
10%
10%
10%
30%
10%
10%
10%
30%
10%
30%
10%
30%
50%
10%
5min 50Lux
5min 75Lux
5min 100Lux
200Lux
50Lux

5min 
10min
10min
10min
10min
20min
20min
30min
30min
30min
5s
30min

75Lux
100Lux
200Lux
100Lux
200Lux
100Lux
200Lux
400Lux
100Lux


1h


Rotaryswitchpreset
C
D
Note: settings can also be changed by remote control
HRC-11. The last action controls. 

E
F10s
Wiring Diagram
L
N
L
NL N
SY SY
NC NC P N L LED+
LED_SY SY P N L LED+ LED_
LED Driver LED Driver
NC NC
DALI+
DALI DALI+
_ _
DALI
HIM14
DALI
HIM14
DALI
- +- +
Detection Pattern
PIR
HF
PIR
HF
PIR
HF
AB
3m 3m 3m
PIRtangentialmovement10m
PIRtangentialmovement5m
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 5/6

Additional Information / Documents
1. Regarding precautionsfor microwave sensor installationand operation, please kindly refer to
www.hytronik.com/download ->knowledge ->Microwave Sensors - Precautions for Product Installation and Operation
2. Regardingprecautions for PIR sensor installationand operation,please kindly refer to
www.hytronik.com/download ->knowledge ->PIR Sensors - Precautions for Product InstallationandOperation
3. RegardingHytronik standardguarantee policy, please refer to
www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy
Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 6/6

The smallest HF motion sensor on the planet, worldwide patented!!!
This sensor is a motion switch, turn on the light on detection of people movement, and turn o after a pre-selected holdtime when there is no
switches on the light automatically when
person enters the room
not switch on when presence detected
After the hold time,then switch o
automatically when no movement is
detected.
Function and options
On-off Function
1
Super compact version
on/off control
Model: HC005S
Detection area
Hold-time
Daylight threshold
Antenna module
Daylight sensor Led indication
Power supply
220-240V out control

with Tridonic switchDIM ballast / driver( Excel ballast/driver, corridor function) , this sensor can also achieve 3-steps dimm ing control...
3-steps dimming control
2
Wiring Diagram
HC005S
Wiring Diagram
HC005S
switchDIM
switchDIM
switchDIM
Detection Pattern
wall mounting height
)m(nrettapgnitnuomllaw)m(nrettapgnitnuomgniliec
ceiling mounting height(m)
100%
30%
30%
30%
30%
75%
75%
75%
75%
50%
50%
50%
50%
100%

I – 5s
II – 30s
III – 1minut
IV – 5 minut
V – 20 minut
VI – 30 minut
I – wyłączone
II – 50 lux
III – 20 lux
IV – 5 lux
V – 2 lux
I – Zasięg - 100%
II – Zasięg - 75%
III – Zasięg - 50%
IV – Zasięg - 30%
V – Zasięg - 10%
100%
75%
50%
30%
10%
1 2 3
4 5 6
7 8 9
Designed in the software, sensor switches
on/o the load right on the zero-cross point,
to ensure the min. current passing through the
relay contact point, and enbale the max. load
and life-time of the relay.
zero-cross point
alternating current
Zero-cross relay operation
Operating voltage
Switched power
Standby power
Warmming-up time
Detection area
Hold time
Daylight threshold
Microwave frequency
Microwave power
Detection range
Detection angle
Mounting height
Operating temperature
IP rating
220-240V
Max.400W (capacitive) Max.1200W(resistive)
0.5W
20s
30/50/75/100%, can be customized
5S/30S/1min/5min/10min/15min/30min, can be customized
2~50lux daylight/twilight/darkness, can be customized
5.8GHz+/-75MHz
0.2mw
Max. ( oxH): 12m x 6m
30 o~150 o
Max.6m
-35oC ~ +70oC
particular application.
Daylight sensor
3
Settings
Detection area can be reduced by selecting the combination on
Detection area
1
Technical Data
IP20 / IP65(mounting in Hytronik special box)
Semko, EMC, CE, R&TTE
Hold-time means the time period you would like to keep the
lamp on 100% after the person has left the detection area.
Hold-time
2
ATTENTION! The luminaire operation may be disturbed by moving
objects in the detection field.
Certicates
1. Due to the risk of interference, the sensors should be located at least 3 m from the next one
2. Due to the dierence in construction, materials used and room equipment, the sensor operation test should be carried out in real conditions.
3. The light intensity [lux] values are for reference only to raise awareness of extreme configuration settings and may dier from the actual value measured by the sensor. It should be taken
into account that the sensor enclosed under the luminaire diuser will react to light dierently compared to the exposed sensor (the enclosed sensor will receive less light than the exposed one,
so the luminaire may remain on even if the light intensity in the room is higher than the selected level). More precise light detection can be provided by a sensor placed outside the lamp,
e.g. in a mounting housing.

Built-in Microwave Motion Sensor with 5.0 SIG Mesh
WSEL475 (HC005S/BT)
ON/OFF CONTROL
Product Description
HC005S/BT is a Bluetooth built-inmicrowave motion sensor with ON/OFF
control. It is designed for professional lighting manufactures who would like
to incorporate wireless control into their luminaires. HC005S/BT is suitable
for any typical indoor applications such as of ce, classroom, car park,
warehouse and other commercial/industrialareas. With Bluetooth wireless
mesh networking, it makes communication much easier without any
hardwiring, which eventually adds values to luminaires and saves costs for
projects. Meanwhile, simple device setup and commissioning can be done
device setup and commissioning can be done via Lena Lighting Clue app.
App Features Hardware Features
Quick setup mode & advanced setup mode
Floorplan feature to simplify projectplanning
Web app/platformfor dedicated project management
Koolmesh Pro iPad version for on-site con guration
Grouping luminaires via mesh network
Scenes
PhotocellAdvance
PhotocellAdvance TM
ON/OFF control with load ratings of:
- 300VA (capacitive)
- 400W (resistive)
Compactdesign
Detailed motion sensor settings Zero crossing detection circuitto reduce in-rush current
and prolong relay lifetime
Dusk/Dawn photocell(Twilightfunction)
Schedule to run scenes based on time and date
Astro timer (sunrise and sunset) Loop-in and loop-out terminals for ef cientinstallation
5-year warranty
Staircase function(primary& secondary)
Compatible with EnOcean BLE switches
Internet-of-Things(IoT) featured
5.0 SIG mesh
iOS
Device  rmware update over-the-air (OTA)
Device social relationscheck
Android for iOS for Android
Smartphone app for both iOS & Android platform
Bulk commissioning (copyand paste settings)
Power-on status (memory against power loss)
Of ine commissioning
for iPad
Koolmesh Pro app for iPad
Web
Different permission levels via authority management
Network sharingvia QR code or keycode
Remote control via gateway support HBGW01
Interoperability with Hytronik Bluetooth product portfolio

for Web
Web app/platform: www.iot.koolmesh.com
Fully supportEnOcean self-poweredswitch
module PTM215B(HBES01/W & HBES01/B)
Subject to change without notice. Edition: 18 Jun. 2021 Ver. A2 Page 1/4