Lennox Hearth Products Adagio-MN User guide

ADAGIO™-MN / ADAGIO-MP / ADAGIO-EN
Page 1 of 2
P/N 775,617M, REV. A, 06/2008
Fireplace Dimensions
Framing Dimensions
Framing Dimensions - All Models
A B C D
in. 22-1/8 40-1/4 15-3/4 44-1/8
mm 562 1022 400 1121
Corner Framing Dimensions - All Models
A B C D E
in. 22-1/8 41-5/8 29-1/2 10 20-7/8
mm 562 1057 749 254 530
Corner Framing With
SV4.5HT-2 Termination
Top Vent With Horizontal Termination In A Corner
Updated Drawings
(done) 1-16-07
Appliance Specifications - Adagio Series Direct Vent Fireplace Heaters
Notes
Due to Lennox' ongoing commitment to quality, all specifications, ratings and
dimensions are subject to change without notice.
** With the facade installed (required - sold separately), the appliance base
will need to be elevated a minimum of 3/4" above the floor to allow for the
proper fit of the facade (i.e. use 3/4" board minimum as platform).
Fireplace Dimensions - Inches (millimeters)
TM
Co-axial DV Vent
4-1/2" (114) Inner
7-1/2" (191) Outer
36-23/32
(933)
21-1/16 (535)
1-7/8
(48)
6-1/16
(154)
8-7/32
(209)
1-1/2
(38)
15-1/32
(382)
15-15/32
(393) 7-11/16
(195)
34
(864)
40-1/32
(1017)
20-3/4
(527)
14-3/4 (375)
5-13/32
(137)
Facade (Required) *
(archedstyle shown)
26-3/4” (680)
38-1/2”
(978)
20-1/4”
(514)
14-13/16” (376)
1/2”
(13)
1/2” (13mm) -
1-1/2” (38mm)
23-1/2” (597)
14-3/4”
(375)
20-3/4”
(527)
Facade (Required) *
(gated style shown)
1/2”
(13)
37-7/8”
(962) 18-3/4
(476)
1/2” (13mm) -
1-1/2” (38mm)
* A filigree inset kit is
also required (sold
separately). See Care
and Operation Manual
for ordering informa-
tion.
Facades
Cat. # Model Description
H5773 ADAGIO-AG Arch Black
H5774 ADAGIO-PF Arch Br. Nickel
H5775 ADAGIO-IG Iron Gates
H5776 ADAGIO-CPD Copper Gates
Arch Facades*
Black & Brushed
Nickel Finishes
Gated Facades
Copper and Iron Gates
uWheninstallinginacornerconfiguration,oneof
the rear stand-offs will need to be removed.
Inches
(millimeters)
C
Back wall of chase/enclosure
(including any finishing materials)
E
D
A
B
7 (178)
�
Facade
Facade
D*
B
VENT FRAMING -
TOP VENT WITH ONE
90°ELBOW
Framing should be
constructed of 2x4
or larger lumber
2 x 4 Header must be
installed, vertical as shown
to allow proper clearance
from venting components to
combustible header. See
Figure 50 for more
details.
A
C
Platform
**
Inches (mm)
8
(203)
5-1/8 13-1/8
(333)
10-1/2
(267)
(130)
3/4” Minimum from
Finished Floor

Page 2 of 2
Specifications and clearances are subject to change without notice.
Refer to Installation Manual before installation of these appliances for
updated dimensions and instructions.
10-1/2”
(267mm)
7"
(178)
5-1/8”
(130 mm)
12-1/8”
(308 mm)
3"
(76 mm)
1"
(25.4 mm)
Adapter SV4.5RCH
Square Horizontal Termination (SV4.5HT-2)
6 to 48 inch Vent
Section, Telescopic
vent section, Elbow or
Appliance Collar
See Page 1 for Min.
Distance to Base of Appliance.
Note: Center line of
Vent Piping is NOT
the Same as the
Center line of the
Framed Opening.
Firestop / spacer (SV4.5HF) shown on the exterior side
of the wall. It may also be installed on the interior side.
* Ceiling Firestop/
Spacer (SV4.5VF)
Vertical
Termination Cap
SV4.5CGV-1
(rated for high
winds and freez-
ing conditions)
Ceiling Framing
10-1/2 in.
(267 mm)
10-1/2 in.
(267 mm)
Typical
Installation
Venting Requirements
Minimum Clearances
Inches (millimeters)
Back 1/2 (13) - 0 (0) Spacers
Sides 1/2 (13) - 0 (0) Spacers**
Top Spacers 0 (0)
Floor 0 (0)***
Bottom of Appliance
To Ceiling 64 (1626)
Vent 3 (76) Top * - 1 (25.4)
Sides & Bottom
Service Clearances -Feet (meters)
Front 3 ft. (0.9 m)
Clearances Shelf Height Listing Information
US
Input (BTU) - Millivolt Models
Natural (NG) & Propane (LP) Gas
Models Fuel Input Rate (BTU / HR)
Adagio-MN NG 13,000 (10,000 Low)
Adagio-MP LP 13,000 (10,000 Low)
ADAGIO™-MN / ADAGIO-MP / ADAGIO-EN
Input (BTU) - Electronic Models
Natural (NG) & Propane (LP) Gas
Models Fuel Input Rate (BTU / HR)
Adagio-EN NG 13,000 (10,000 Low)
Adagio-EP
if field converted
LP 13,000 (10,000 Low)
Tested to ANSI Z21.88 (in
Canada, CSA-2.33), and
CAN/CGA-2.17-M91 in both
USA and Canada, as vented
gas fireplace heaters.
Models
Combustible Shelf Height - Inches (millimeters)
Top Vent - with One 90 Degree Elbow
Adagio-MN
Adagio-MP
Adagio-EN
Secure Vent Secure Flex (flex elbow)
*52 (1321) *53-3/4 (1365)
* Includes 4” clearance to combustibles (required above vent components)
Side Wall Clearances (top view)
* Note: 3 in. (75 mm) above any horizontal vent component, except for installations which have and elbow connected to fireplace collar and that ends
in a horizontal termination (this installation requires a 4” clearance above vent).
** Note: See Installation Instructions Manual on Page 6 (Step 1) for clearance requirements to the nailing flange located at each side of the unit and
any screw heads adjacent to it.
***Note: To ensure proper fit of the facade, the appliance base will need to be elevated 3/4" above the floor to allow for the proper fit of the facade (i.e.
Use 3/4" board as platform).
Do not insulate the
space between the
appliance and the
area above it.
*Shelf Height
(see table)
Shelf Above Fireplace - Top Vent
Drywall
Header
Top Spacers
4” �
(102mm)
u 4" clearance is
required above the
elbow for installations
that require an elbow at
the top of the unit and
that ends in a horizontal
termination.
17"
(432)
14" (356) Min. Distance to
Unprotected Side Wall
45
°
Combustible Materials Allowed
In Shaded Area “Safe Zone”
2” (51) Minimum
Clearance to Combustibles
12" (305)
5"
(127)
Min. Distance
8-1/4” (210) to
Protected Side Wall
Top View Of
Fireplace
Side
Wall Side
Wall
inches (millimeters)
12 (305) Mantel
10 (254) Mantel
8 (203) Mantel
6 (152) Mantel
4 (102) Mantel
16
(406)
12
(305) 10
(254) 2 (51) Mantel
Top Of
Appliance
6
(152)
8
(203)
Mantel Clearances
Inches (mm)
14
(356)
Report No. 116-F-48-5
Printed in U.S.A. © 2007 Lennox Hearth Products
P/N 775,617M REV. A 06/2008