Lennox Hearth Products E36ODG User manual

1
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
GAS APPLIANCE
KITS AND ACCESSORIES
GAS CONVERSION KIT
Figure 1
In Canada:
THE CONVERSION SHALL BE CARRIED OUT
IN ACCORDANCE WITH THE REQUIREMENTS
OF THE PROVINCIAL AUTHORITIES HAVING
JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN1-B149.1
AND .2 INSTALLATION CODE.
LA CONVERSION DEVRA ÊTRE EFFECTUÉE
CONFORMÉMENTAUXRECOMMANDATIONS
DES AUTORITÉS PROVINCIALES AYANT
JURIDICTION ET CONFORMÉMENT AUX
EXIGENCESDUCODED'INSTALLATIONCAN1-
B149.1 ET.2.
Gas conversion kits are available to adapt your
appliancefromthe useofone typeofgas tothe
use of another. These kits contain all the nec-
essary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure.
CAUTION: THEGAS SUPPLYSHALL BESHUT
OFF PRIOR TO DISCONNECTING THE ELEC-
TRICALPOWER,BEFOREPROCEEDINGWITH
THE CONVERSION.
WARNING: THIS CONVERSION KIT SHALL BE
INSTALLED BY A QUALIFIED SERVICE AGENCY IN
ACCORDANCE WITH THE MANUFACTURER'S IN-
STRUCTIONS AND ALL APPLICABLE CODES AND
REQUIREMENTS OF THE AUTHORIZED HAVING
JURISDICTION. IF THE INFORMATION IN THESE
INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A
FIRE, EXPLOSION OR PRODUCTION OF CARBON
MONOXIDE MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
THE INSTALLATION IS NOT PROPER AND COM-
PLETEUNTILTHEOPERATIONOFTHECONVERTED
APPLIANCE IS CHECKED AS SPECIFIED IN THE
OWNERINSTRUCTIONSSUPPLIEDWITHTHEKIT.
THE QUALIFIED SERVICE AGENCY PERFORMING
THIS INSTALLATION ASSUMES RESPONSIBILITY
FOR THIS CONVERSION.
AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION
SERAINSTALLÉPARUNEAGENCEQUALIFIÉEDESERVICE
CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET
TOUTES EXIGENCES ET CODES APPLICABLES DE
L'AUTORISÉSAVOIRLAJURIDICTION. SIL'INFORMATION
DANS CETTE INSTRUCTION N'EST PAS SUIVIE
EXACTEMENT, UN FEU, EXPLOSION OU PRODUCTION DE
PROTOXYDEDECARBONEPEUTRÉSULTERLEDOMMAGES
CAUSER DE PROPRIÉTÉ, PERTE OU BLESSURE
PERSONNELLEDEVIE. L'AGENCE QUALIFIÉE DE SERVICE
EST ESPONSABLE DE L'INSTALLATION PROPRE DE CET
ÉQUIPMENT. L'INSTALLATION N'EST PAS PROPRE ET
COMPLÉTE JUSQU'À L'OPÉRATION DE L'APPAREIL
CONVERTI EST CHÉQUE SUIVANT LES CRITÈRES ÉTABLIS
DANS LES INSTRUCTIONS DE PROPRIÉTAIRE
PROVISIONNÉES AVEC L'ÉQUIPEMENT.
Step 1. Turn off the gas supply to the appli-
ance and disconnect the electrical power.
Step 2. Carefully remove the logs. Exercise
care so as not to break the logs. Remove any
lava rock within the burner pan.
Step 3. Remove the burner tube with attached
venturitube. Refer to Figure1 for the location
of the control valve and regulator, main orifice
and pilot.
750,222M
REV. A 07/2006
Access
Cover
Control Valve
And Regulator
Pilot Orifice Burner Tube
Main
Orifice
stiKnoisrevnoCsaG
sledoMtaNoTPLPLoTtaN
GDO63E GDO24E .oNgolataC 5194H .oNgolataC 6194H
GDO63E GDO24E .oNledoM N041BD-KCG .oNledoM P870BD-KCG

2NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Figure 6
Step 8. Turn on gas supply and test for gas
leaks, using a soapy water solution.
Step7. Attach appropriateconversion kitlabel
(
Figure6 )to therating plateon the appliance.
Printed in U.S.A. © 2006 by Lennox
P/N 750,222M REV. A 07/2006
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LHP
1110 West Taft Avenue
Orange, CA 92865
Figure 3
Figure 2
Figure 4
Note: If the ignitor is damaged, a replacement
kit is available, order Catalog Number 87L54.
Step 6. Reassemble the remaining compo-
nents by reversing the procedures outlined in
the preceding steps.
Pilot Stage
Terminal Pressure-Tap
(Inlet) Pilot Gas
Outlet
Supply Gas
Inlet
Pressure-Tap
(Manifold)
Burner Stage
Terminal
Ground
(TP)
PILOT
OUT
VENT
LO
TH TP
TH
TP
HI
IN
IN
Gas Outlet
To Burner
Regulator
Mounting Screw
Figure 5
Electronic Appliances
Step 4. Dexen Electronic Valves - See
Figure 2
and the instructions provided with the kit. Re-
move and discard the two pressure regulator
mountingscrews. Remove thepressureregu-
lator and diaphragm. Discard all removed
components. Ensure the provided diaphragm
isinstalledproperlyontothereplacementpres-
sure regulator and install the new pressure
regulator using the new screws supplied with
the kit. Tighten screws.
See
Figure 3 and replace the pilot orifice as
follows: Remove pilot hood assembly to access
the pilot orifice. Remove and replace the orifice
with the one provided with the kit. Exercise
extreme care to prevent damage to or break-
age of the ignitor assembly.
Step 5. (Refer to Figure 5 )
A. Remove the orifice from the manifold and
replaceit withthe oneprovided inthe kit.Seethe
following table for orifice sizes for natural and
propanemodels .Figure4 illustrates theorifice.
B. Retrieve the burner and slide the venturi
tube over the orifice. Set the shutter adjusting
opening as shown in Figure 5 .
Remove Tube
Regulator
Orifice
Remove Clip
Shutter
Opening
RENRUBNIAM GNITTESGNINEPORETTUHSYROTCAF
sledoM saGlarutaN )mm(sehcni saGenaporP )mm(sehcni
llA sledoM 61/1)85.1(2/1)7.21(
.oNledoM ezisecifirO
larutaNenaporP
sledoMllA 82# 5041.0 74# 5870.0
Use pipe joint compound or Teflon tape on all
pipe fittings before installing (ensure propane
resistant compounds are used in propane ap-
plications, do not use pipe joint compounds
on flare fittings).
THIS APPLIANCE HAS BEEN CONVERTED TO:
NATURAL GAS
INPUT BTU/HR – 50,000
MANIFOLD PRESSURE – 3.5"
ORIFICE SIZE – (0.130)
THIS APPLIANCE HAS BEEN CONVERTED TO:
PROPANE/LPG
INPUT BTU/HR – 50,000
MANIFOLD PRESSURE – 10"
ORIFICE SIZE – (0.080)
ELECTRONIC PILOT
Pilot
Hood
Sensor
Ignitor
PROPANE NATURAL