Lepa AquaChanger 240 User manual

AquaChanger 240

Weight (w/o fan)
Material
Bearing
MTBF
Motor Speed
Rated Voltage
Rated Current
Dimension
Material
Material
Length
Dimension
Speed
Rated Voltage
Rated Current
Air Flow
Stac Pressure
Noise Level
Connector
Compability
Intel® LGA 775/1150/1151/1155/1156/1366/2011/2011-3
AMD® AM2/AM2+/AM3/AM3+/FM1/FM2/FM2+
120 x 120 x 25 mm
500 ~ 2300 rpm ±10%
12V
0.38 A
22.5 ~ 103.6 CFM
38.2 ~ 176.0 m3/h
0.2 ~ 4.5 mm- H2O
14 ~ 35 dBA
4 pin PWM
2 years
Copper
Ceramic Bearing
50,000 hrs
2700rpm ±10%
12V
0.3A
274 x 120 x 27 mm
Aluminum
Rubber
300 mm
730 g
Pump
Cold Plate
Radiator
Tube
Warranty
Bracket
Fan
Model LPWAC240-HF
Specification
*Some MB put the capacitors around the boarder of CPU bracket, please carefully install the
cooler on can avoid the mechanical interference.

A Cooler x 1
B Fan x 2 C Back Plate x 1
D Posion Screw × 4
F Stand-off × 4 G Case Screw × 8 H Fan Screw × 8 I Intel LGA2011 Screw × 4
J Spring Screw × 4 K Insulang Sheet × 4 L Intel Bracket × 2
N Bracket Screw × 4 O Thermal Grease × 1 P PWM Y cable x 1
M AMD Bracket × 2
E Square Washer x 1
Q Molex Adaptor x 1
Part list

Intel Installation
AquaChanger 240

Step 1
EN
Aach the fan and the radiator to the case.
Intel Installation

*Aligning
LGA1366
LGA775
LGA 115X
LGA 775/1150/1151/1155/1156/1366
C
D
Step 2-1
Intel
EN
<If your CPU socket is Intel LGA 2011,
please skip to step 3-2.>
Install the screw into the corresponding
posion hole on the back plate for your
CPU socket.

Step 2-2
LGA775
C
E
EN
For LGA 775, please aach and click the square washer to the
center of the back plate.

Intel
EN
Install the back plate on the back of motherboard; place the stand-off
on the motherboard to fix the back plate.
Step 3-1 LGA 775/1150/1151/1155/1156/1366
F
C
D

Step 3-2
EN
Please fasten the LGA 2011 screw directly to the motherboard unl
all four screws are secured. (Socket LGA 2011 does not required to use
the back plate for installaon)
LGA 2011/2011-3
I

Intel
Step 4
EN
Install the Intel bracket to the pump.
NL

Step
5
EN
Apply the thermal grease on the CPU surface.
O

Intel
Step 6
EN
Remove the protecon film on the cold plate.

Step
7
EN
Place the pump on the CPU and ghten the four spring screws.
J

Connect the pump power connector to 3-pin or 4-pin connector on the motherboard.
Noce: If you recognize that your mainboard's CPU fan or PWM sockets do not provide enough voltage to power the pump, please use the included 4-pin
Molex adaptor and connect the pump directly to your PSU.
Intel
Step 8
EN
Pump
4 pin
Pump
3 pin
or

Step
9
EN
Connect the fan connector to the 4-pin connector on
the motherboard.

AMD Installation
AquaChanger 240

EN
Aach the fan and the radiator to the case.
Step 1
AMD Installation

EN
Sck the insulang sheet on the corresponding posion.
Step 2
AMD
K
C

Step 3
EN
Please remove the original heatsink mount
holder before further installaon.

Step 4
EN
Please aach and click the square washer to
the center of the back plate and install the screw
into the corresponding posion hole on the back plate for your CPU socket.
*Aligning
D
C
E
AMD