Lepa EXllusionm 240 User manual

Weight (w/o fan)
Material
Bearing
MTBF
Motor Speed
Rated Voltage
Rated Current
Dimension
Material
Material
Length
Dimension
Speed
Rated Voltage
Rated Current
Air Flow
Stac Pressure
Noise Level
Connector
Compability
Intel® LGA 775/1150/1151/1155/1156/1366/2011/2011-3
AMD® AM2/AM2+/AM3/AM3+/FM1/FM2/FM2+
120 x 120 x 25 mm
500 ~ 1800 rpm ±10%
12 V
0.3 A
22.5 ~ 81.1 CFM
38.2 ~137.8 m3/h
0.2 ~2.8 mm-H2O
14 ~ 30 dBA
4 pin PWM
2 years
Copper
Ceramic Bearing
50,000 hrs
4000 rpm ±10%
12 V
0.3 A
274 x 120 x 32 mm
Aluminum
PU Plasc (ID-9.5mm/OD-12.5mm)
350 mm
1120 g
Pump
Cold Plate
Radiator
Tube
Warranty
Bracket
Fan
Model LPWEL240-HF
Specification
*Some MB put the capacitors around the boarder of CPU bracket, please carefully install the
cooler on can avoid the mechanical interference.

A Cooler x 1
B Fan x 2 C Back Plate x 1 D Posion Plate x 1
F Stand-off × 4
G Case Screw × 8 H Fan Screw × 8 I Set Screw x 4
M Scraper x 1 N Thermal Grease x 1
O 24P power adaptor x 1 P Dye x 3 Q Coolant 500 ml x 1 R Filler p x 1
S Fixed ring x 1 T Tray with hole x 1 U Tray x 1 V Indicaon scker x 1
J Washer x 4
K PWM Y cable x 1 L Molex Adaptor x 1
E Posion Screw x 4
Part list

Installation

O
Step A
PRE-INSTALLATION
Unplug the PC power supply unit’s 24P main power and water block’s 3pin power connectors from MB. Connect the
above connectors to the included 24P power adaptor . TO urn on the power supply unit, this will also power on the
pump. (Please perform this operation outside the chassis.)
EN

Step B
P
If you do not want to dye the coolant, please skip this step. Open the filler cap from the water block, and drop the
adequate dye (coolan Pt) into the water block. Firmly bolt the filler cap back to the water block.
Warning: If the filler cap are not firmly bolt back, the coolant might leak and cause damage to system components.
Such damage is not covered in the warranty.
EN

Step 1
INSTALLATION
H
B
A
EN Attach the fan and the radiator to the case.

Step 2-A-1
LGA 775/1150/1151/1155/1156/1366/All AMD Socket
LGA 1366
LGA 115X
LGA755
All AMD socket
E
C
EN <If your CPU socket is Intel LGA 2011, please skip to step 2-B.> Install the scre Ew E into the corresponding posion hole
on the back plate C f
C or your CPU socket.

C
J
F
Step 2-A-2
E
Install the back plat Ce C on the back of motherboard, place the washer J inJ to the posion scre Ew E and fix them
with stand-off F .
F
EN

Step 2-A-3
I
D
F
Place posion plate D on stand-off F and use set screw I to fix.
I
D F
EN

Step 2-B
LGA 2011/2011-3
LGA 2011/2011-3
E D
F
Place posion plate D on stand-off F and use posion screw E to fix. (Socket LGA 2011 does not require the
back plate)
FD E
EN

Step 3
N
M
Apply the thermal grease on the CPU surface.
EN

Step 4
Remove the protecon film on the cold plate.
EN

Step 5
Place the pump on the CPU and ghten the two screws.
EN

Step 6
Pump
4 pin
Pump
3 pin
or
Connect the pump power connector to 3-pin or 4-pin connector on the motherboard.
Noce: If you recognize that your mainboard's CPU fan or PWM sockets do not provide enough voltage to power the pump,
please use the included 4-pin Molex adaptor and connect the pump directly to your PSU.
EN

Connect the fan connector to the 4-pin connector on the motherboard.
Step 7
B
K
EN

Step 8
U
Place tray on VGA card to isolate the possible leakage coolant from unsecure filler cap.
Warning: If the filler cap are not firmly bolt back, the coolant might leak and cause damage to system components. Such
damage is not covered in the warranty.
U
EN

Step A
Indicaon scker:
V
V
Refilling Coolant
If the water block is horizontally placed and the coolant
volume is below this white indicator, please refill the
coolant.
If the water block is vercally placed and the coolant
volume is below this white indicator, please refill the
coolant.
EN

Step B-1
Coolant Refill O
1. Unplug the MB/CPU/VGA/HDD/SSD/Peripheral power connectors from power supply unit, and water block’s 3-pin power connector from MB.
2. Bridge the power supply unit’s MB 24-pin main connector and water block’s power connectors via included 24P power adaptor O .
3. Turn on the power supply unit, this will also power on the pump.
O
EN

Step B-2
Coolant Refill
S
S
Q
T
EN
Open the filler cap from the water block, place tray T and screw fixed ring S . Refill the adequate Coolant Q into the water
block. Aer refilling, remove tray & fixed ring. Firmly bolt the filler cap back to the water block.
Noce: You must horizontally place your system,with water block top side parallel to the ground for this operaon.
S
TQ