LevelOne GSW-0507 User manual

LevelOne
User Manual
GSW-0507 / GSW-0807
5/8-Port Gigabit Ethernet Switch
V1.0.0-0803

FCC Certifications
This Equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any
interference received; including interference that may cause
undesired operation.
CE Marking Warning
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55022 Class B for ITE, the
essential protection requirement of Council Directive 89/336/EEC on
the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it
may be possible that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form
without written consent from the company.
2

3
Introduction
The GSW-0507/GSW-0807 device are powerful,
high-performance Gigabit Ethernet switch, with all ports
capable of 10, 100 or 1000Mbps auto-negotiation operation
(NWay), which means the switch could automatically
negotiate with the connected partners on the network speed
and duplex mode. It is ideal for micro-segmenting large
networks into smaller, connected subnets for improved
performance, enabling the bandwidth demanding multimedia
and imaging applications. Moreover, the 10/100/1000Mbps
auto-sensing ability provides an easy way to migrate
10/100Mbps to 1000Mbps network with no pain. Compared to
the shared 10Mbps or 100Mbps networks, the switch delivers
a dedicated 10/100/1000Mbps connection to every attached
client with no bandwidth congestion issue. The
GSW-0507/GSW-0807 switch also supports auto MDI / MDI-X
function. Each port could be used to connect to another switch
or hub with no crossover RJ-45 cable.
Store-and-forward switching mode promises the low latency
plus eliminates all the network errors, including runt and CRC
error packets. To work under full-duplex mode, transmission
and reception of the frames can occur simultaneously without
causing collisions as well as double the network bandwidth.
The switch is plug-and-play without any software to configure
and also fully compliant with all kinds of network protocols.

4
Package Contents
•GSW-0507/GSW-0807
•Power Adapter
•User Manual
•Wall-Mounting Kit
If any of the above items are damaged or missing, please
contact your dealer immediately.
Installation
The setup of the GSW-0507/GSW-0807 Switch can be
performed using the following steps:
1. Install the Switch in a fairly cool and dry place. See
Technical Specification for the acceptable operation
temperature and humidity ranges.
2. Install the Switch in a site free from strong electromagnetic
source, vibration, dust, and direct sunlight.
3. Leave at least 10cm of space at the left and right hand
side of the Switch for ventilation.
4. Visually inspect the DC power jack and make sure that it is
fully secured to the power adapter.

LED Definition
GSW-0507 Front Panel
GSW-0807 Front Panel
On Power is on.
PWR Off Power is off.
On One LED indicator will light green when a
device is connected to the corresponding port.
Link/Act
(1~5/1~8) Blinking The port is transmitting/receiving data.
Rear Panel
The rear panel of the GSW-0507/GSW-0807 switch consists
of a DC power connector and 5/8 10/100/1000Mbps RJ45
Ports. The following figure shows the rear panel of the Switch.
yGSW-0507
yGSW-0807
5

6
Stations Connection
Connect each station to the switch by twisted-pair cable. Plug
one RJ-45 connector into a RJ-45 port of the switch, and plug
the other RJ-45 connector into the station’s network adapter.
Power on the switch and then system is ready.
For cable selection, refer to the following table.
Switches Connection
In making a switch interconnection, you could use any port to
connect another switch with straight or crossover cable. As all
the ports support auto MDI / MDI-X function, using a straight
cable to make a switch-to-switch connection is allowed.
For cable selection, refer to the following table：
Network Speed Cable Type Max. Length
10Mbps Cat. 3, 4, 5 UTP/STP 100 meters
100Mbps Cat. 5 UTP/STP 100 meters
1000Mbps Cat. 5 UTP/STP 100 meters

7
Specification
Standard yIEEE 802.3 10BASE-T
yIEEE 802.3u 100BASE-TX
yIEEE 802.3ab 1000BASE-T
yIEEE 802.3x Full Duplex Operation & Flow
Control
Interface y5/8 * 10/100/1000Mbps RJ-45 Gigabit Ethernet
Ports (GSW-0507/GSW-0807)
NWay Protocol
Support
y10Mbps: Full/Half duplex
y100Mbps: Full/Half duplex
y1000Mbps: Full duplex only
MAC Address
Table
y1K MAC Address entries (GSW-0507)
y8K MAC Address entries (GSW-0807)
Buffer Memory y832K bits (GSW-0507)
y144KBytes (GSW-0807)
Jumbo Frame y12K Byte (GSW-0507)
y9K Bytes (GSW-0807)
Power Supply y5VDC-1A, External (GSW-0507)
y12VDC-1A, External (GSW-0807)
Temperature yOperating Temperature: 0℃~40℃
yStorage Temperature: -10℃~70℃
Humidity yOperating Humidity: 10%~90% non-condensing
yStorage humidity: 5%~95% non-condensing
EMI yCE and FCC classA

8
Technical Support
Thank you for selecting LevelOne products. LeveOne’s
website contains the latest user documentation and soft-ware
updates for LevelOne products.
Please contact LevelOne Technical Support through our
website.
World Wide Web
http://www.level1.com