LevelOne FSW-2411TX User manual

LevelOne
FSW-2411TX
24port 10/100Mbps 13”Fast Ethernet Switch
USER'S GUIDE

2
FCC WARNING
This equipment has been tested and found to comply
with the limits for a Class A computing device
pursuant to Part 15 of FCC Rules, which are
designed to provide reasonable protection against
electromagnetic interference in a commercial
environment.
Changes or modifications to the equipment not
expressly approved by the party responsible for
compliance could void the user's authority to operate
the equipment.
CE MARK WARNING
THIS IS A CLASS A PRODUCT. IN A DOMESTIC
ENVIRONMENT THIS PRODUCT MAY CAUSE RADIO
INTERFERENCE IN WHICH CASE THE USER MAY BE
REQUIRED TO TAKE ADEQUATE MEASURES.

3
TABLE OF CONTENTS
UNPACKING INFORMATION-----------------------------------4
PRODUCT INTRODUCTION-------------------------------------5
FAST ETHERNET TECHNOLOGY-------------------------------------------- 5
SWITCHING TECHNOLOGY----------------------------------------------------5
FEATURES---------------------------------------------------------------------------6
THE FRONT PANEL---------------------------------------------------------------7
CABLING------------------------------------------------------------------------------8
STATUS LEDS----------------------------------------------------------------------8
THE REAR PANEL-----------------------------------------------------------------8
INSTALLATION-----------------------------------------------------------10
TO LOCATE THE SWITCH ON A DESKTOP-----------------------------10
TO STACK YOUR SWITCH----------------------------------------------------10
RACKMOUNT PLACEMENT-------------------------------------------------- 10
HELPFUL SUGGESTIONS--------------------------------------12
Prior to Installation----------------------------------------------------------------12
Half-and Full-Duplex------------------------------------------------------------ 12
Fast Ethernet-----------------------------------------------------------------------13
Auto-Negotiation-------------------------------------------------------------------13
MAC Address Table--------------------------------------------------------------14
Sample Application---------------------------------------------------------------15
Troubleshooting--------------------------------------------------------16
PRODUCT SPECIFICATIONS--------------------------------17

4
A. UNPACKING INFORMATION
Thank you for purchasing LevelOne FSW-2411TX 24 port 10/100Mbps
13”Fast Ethernet Switch. Before continuing, please check the
contents of the product package. This product package should contain
the following items:
ØOne LevelOne FSW-2411TX 24 port 10/100Mbps 13”Fast Ethernet
Switch
ØOne Power Cord
ØFour Rubber Feet (for desktop placement)
ØOne Rackmount Kit
ØFour Stackable stand
ØUser’s Guide
If anything is missing, please contact your place of purchase.

5
B. PRODUCT INTRODUCTION
This chapter describes the features of the Switch and some background
information about Ethernet/Fast Ethernet switching technology.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of
desktop computing applications are fueling the need for high
performance networks. A number of high-speed LAN technologies have
been proposed to provide greater bandwidth and improve client/server
response times. Among them, 100BASE-T (Fast Ethernet) provides a
non-disruptive, smooth evolution from the current 10BASE-T technology.
The non-disruptive and smooth evolution nature, and the dominating
potential market base, virtually guarantee cost effective and high
performance Fast Ethernet solutions in the years to come.
100Mbps Fast Ethernet is a new standard specified by the IEEE 802.3
LAN committee. It is an extension of the 10Mbps Ethernet standard
with the ability to transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps Fast
Ethernet is compatible with all other 10Mbps Ethernet environments, it
provides a straightforward upgrade and takes advantage of the existing
investment in hardware, software, and personnel training.
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology
is the development of switching technology. A switch bridge Ethernet
packets at the MAC address level of the Ethernet protocol transmitting
among connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch increases
capacity and decreases network loading by dividing a local area network
into different segments, which don’t compete with each other for
network transmission capacity.

6
The switch acts as a high-speed selective bridge between the individual
segments. The switch, without interfering with any other segments,
automatically forwards traffic that needs to go from one segment to
another. By doing this the total network capacity is multiplied, while
still maintaining the same network cabling and adapter cards.
For Fast Ethernet networks, a switch is an effective way of eliminating
problems of chaining hubs beyond the “two-repeater limit.” A switch can
be used to split parts of the network into different collision domains,
making it possible to expand your Fast Ethernet network beyond the
205-meter network diameter limit for 100BASE-TX networks. Switches
supporting both traditional 10Mbps Ethernet and 100Mbps Fast
Ethernet are also ideal for bridging between the existing 10Mbps
networks and the new 100Mbps networks.
Switching LAN technology is a marked improvement over the previous
generation of network bridges, which were characterized by higher
latencies. Routers have also been used to segment local area networks,
but the cost of a router, the setup and maintenance required make
routers relatively impractical. Todayswitches are an ideal solution to
most kinds of local area network congestion problems.
Features
The Switches were designed for easy installation and high performance
in an environment where traffic on the network and the number of user
increase continuously.
These Switches provide immediate access to a rapidly growing network
through a wide range of user-reliable functions.
The Switches are ideal for deployment with multiple high-speed servers
for shared bandwidth 10Mbps or 100Mbps workgroups. With the highest
bandwidth 200Mbps (100Mbps full-duplex mode), any port can provide
workstations with a congestion-free data pipe for simultaneous access
to the server.
The Switches are expandable by cascading two or more switches
together. As all ports support 200Mbps, the Switches can be cascaded
from any port and to any number of switches.

7
The LevelOne FSW-2411TX 24port 10/100Mbps 13”Fast Ethernet
Switch are a perfect choice for site planning to upgrade to Fast Ethernet
in the future. Ethernet workgroups can connect to the Switches now,
and change adapters and hubs anytime later without needing to change
the Switches or reconfigure the network.
The Switches combine dynamic memory allocation with store-and-
forward switching to ensure that the buffer is effectively allocated for
each port, while controlling the data flow between the transmit and
receive nodes to guarantee against all possible packet loss.
The LevelOne FSW-2411TX 24 port 10/100Mbps 13”Fast Ethernet
Switch are an unmanaged 10/100 Fast Ethernet Switch that offers
solutions in accelerating small Ethernet workgroup bandwidth. Other
key features are:
lTwenty-four 100/10Mbps Switch ports.
lStore-and-Forward technology.
lAuto-Negotiation support for each TP port.
lIEEE 802.3x Flow-Control support for Full-Duplex operation.
lBack-Pressure support for Half-Duplex operation.
lBridging capability for 100Mbps and 10Mbps segments.
lAll ports support Auto-MDIX function.
The Front Panel
LevelOne 24 port 10/100Mbps 13”Fast Ethernet Switch
Port Speeds
100/10Mbps TP Ports
Each 100/10Mbps TP port provides an Auto-Negotiation function that
senses for the attached device's maximum operating speed and
automatically sets the Switch to operate at that speed. Users only
need to connect a network device into any TP port.

8
Cabling
10Mbps –Category 3, 4, or 5 TP cabling can be used for transmitting
data at 10Mbps or 20Mbps bandwidth on 10BASE-T networks.
100Mbps –Only Category 5 TP cabling can be used for transmitting
data at 100Mbps or 200Mbps bandwidth on 100BASE-TX networks.
Port Type Cable Type Connector
10BASE-T Category 3, 4 or 5 TP RJ-45
100BASE-TX Category 5 TP RJ-45
Note: Category 5 TP cable should be used whenever installing new TP
cabling.
Status LEDs
This LevelOne 24 port 10/100Mbps 13”Fast Ethernet Switch comes with a
complete range of LEDs. The table below lists each LED’s name, color
and a brief description of its function.
•One for power On/Off
•One per port for Link/Activity
•One per port for Full-Duplex/Collision
NAME COLOR FUNCTION
PWR Green •Lit: Power "On"
LINK/ACT Green •Lit: When the port has a valid phy
sical connection (Link)
with another device.
•
Blinks: When the port is sending or receiving data
(Activity).
FD/COL Amber •Lit: When the port is set to Full-Duplex mode.
•Blinks: When a collision is detected,in Half-Duplex mode.
The Rear Panel

9
Power Socket
The Power Socket is designed to be used with the power cord
included in the product package.
.Attach the female end of the cord to the power connector on
the back panel.
.Attach the male end of the cord to a grounded power outlet.
Fan Note: Please keep the fan area clear, so that the cooling function is
not impaired.

10
C. INSTALLATION
This LevelOne 24 port 10/100Mbps 13”Fast Ethernet Switch is "Plug &
Play." They do NOT require software configuration. Users can
immediately use any of the features of this product simply by attaching
the cables and turning on the power.
TO LOCATE THE Switch ON A DESKTOP
a) Attach the four rubber feet included in the product package to the
bottom of the Switch, one in each corner.
b) Place the Switch on a clean, flat desk or table top close to a power
outlet.
C) Plug in all network connections and the power cord
To stack your Switch
a) Attach the four stackable stand included in the product package to
the bottom of the Switch, one in each corner.
b) Now , you can can use the switch to stack with other switch with
stackable stand.
C) Plug in all network connections and the power cord
RACKMOUNT PLACEMENT
This LevelOne 24 port 10/100Mbps 13”Fast Ethernet Switch can be
mounted in an EIA standard-sized 19-inch rack.
1. Attach one (1) rackmounting bracket on each side of the Switch’s
front panel with the provided screws.