LevelOne WAB-5120 User manual

- 1 -
LevelOne
WAB-5120
300Mbps Wireless Outdoor PoE Access Point/Bridge
Quick Installation Guide
English Deutsch

- 2 -
Table of Content
English......................................................................................................................................................- 3 -
Deutsch .....................................................................................................................................................- 9 -
This guide covers only the most common situations. All detailed information is described in the user
manual.

- 3 -
English
Hardware Installation
1. Loosen the screw with a screwdriver.
Grab the cover and pull it back harder to take it out
2. Plug Cat.5/5e/6 cable into the RJ-45 LAN1 port. Do not use the RJ45 LAN2 port.
3. Power on the CPE by press the black PWR button beside the LAN 1 Ethernet port.
4. Attach and fasten the removable cover to the bottom of the unit with the screw

- 4 -
5. Plug the power cord into the DC port of the PoE injector
6. Plug the other side of the Cat.5/5e/6 cable into the PoE port of the PoE injector. The
installation is finished and looks like the following picture.

- 5 -
Configuration
Check Your Network Settings to login web UI
You need to assign your PC a Static IP address so the WAB-5120 can communicate with your
PC during configuration.
Select “Control Panel” > “Network Connections”.
Right click the “LocalArea Connection” and choose “Properties”.
Select the TCP/IP protocol for your network card.
Click on the Properties button. You should then see the following screen.
Click on “Use the following IP address” and enter the following IP address and subnet mask.
IP address: 192.168.1.229 Subnet mask: 255.255.255.0
Click “OK”.
Open your Web browser (Internet Explorer is recommended).
Then enter: http://192.168.1.1
You will see WAB-5120 Login page as following picture
Use the following username and password to login the device.
User name: admin Password: admin

- 6 -
AP Mode
1. Choose Wireless > Basic Settings for the wireless basic settings.
Click Apply.
If security is required, open Wireless > Profile Setting and enter “VAP Profile 1 Settings” as
below. Choose Network Authentication to change the security settings. Click Apply.

- 7 -
CPE Mode
1. Choose Wireless > Basic Settings for the wireless basic settings.
In Wireless mode, choose “Wireless Client” to operate in Client mode.
Click Apply.
2. Click the “Site Survey” button beside Wireless Mode. It will scan all the available access
points within coverage. Select the one you prefer to connect to, and click Selected to
establish the connection. You can also click Scan to re-scan the available access points.

- 8 -
3. If the AP you connect to needs authentication or password, click Profile Settings in the left
column, fill out the corresponding items, and click Apply for data encryption.
Congratulations!
The AP – CPE connection is now successfully configured.

- 9 -
Deutsch
Installation der Hardware
1. Lösen Sie die Schrauben mit einen Schraubendreher. Entfernen Sie das Gehäuse mit einem
kräftigen Ruck.
2. Stecken Sie ein Cat.5/5e/6 Kabel in den RJ45 LAN1-Port. Verwenden Sie NICHT den RJ45
LAN2-Port.
3. Stellen Sie die Stromversorgung an, indem Sie die schwarze PWR-Taste neben dem
LAN1-Ethernet-Port drücken.

- 10 -
4. Befestigen Sie das Gehäuse mit der mitgelieferten Schraube auf der Halterung.
5. Stecken Sie das Stromkabel in den DC-Port des PoE-Injektors.
6. Verbinden Sie das andere Ende des Cat.5/5e/6 Kabel mit dem PoE-Port des PoE-Injektors.
Die Installation ist nun beendet und sollte dem folgenden Bild entsprechen.