LevelOne WAP-6221 User manual

密级
WAP-6221
N300 PoE Wireless Access Point, In-Wall
Mount, Controller Managed
User’s Manual
V1. 0_20161018

2
密级
Contents
Chapter 1 Equipment Instruction and Power Supply................................................................................... 4
1. PoE Power supply：................................................................ 4
2. Operation Mode description and usage:.................................................. 4
Chapter 2 Run and Login..............................................................................................................................6
Chapter 3. Operation mode setting ....................................................................................................................7
1. Router operation:....................................................................................................................................... 8
2. Repeater operation: ................................................................................................................................... 8
3. Wireless Coverage:.................................................................................................................................. 10
Chapter 4 System Tools and Advanced Settings:.........................................................................................12
1.System Tools ................................................................... 12
2. Wireless ....................................................................... 13
3. Network Setting ................................................................ 14
4.Management .................................................................... 15
4.1 System.......................................................................................................................................... 15
4.2 User.............................................................................................................................................. 16
4.3 Logs.............................................................................................................................................. 16
4.4 Upgrade Firmware ....................................................................................................................... 17
4.5 System Time ................................................................................................................................ 17
Appendix A LICENSE STATEMENT / GPL CODE STATEMENT..........................................................19

3
密级
This quickly guider is for our 300Mbps in wall AP. It will instruct you how to
configure and manage this Access Point/Router/Repeater in right ways.
Packing Contents:
● 300Mbps in wall AP
● QIG
● Setting accessory

4
密级
Chapter 1 Equipment Instruction and Power Supply
1. PoE Power supply：
There are two way to supply power for this device:
A. PoE Switch: pls make sure the PoE switch comply with IEEE 802.3af standard; then connect switch and
in wall AP as follow:
P2 Power Supply
2. Operation Mode description and usage:
There are three operation mode in our in wall AP: Internet Settings, Wireless Repeater, Wireless
Coverage
Internet Settings: WAN Connection, from cable internet to Wifi internet by setup PPPoE, Dynamic
IP, Static IP or PPTP in Internet Settings
P3 Internet Setting
Wireless Repeater：The in wall AP can bridge and extend the existing WiFi signal in this operation
mode, for example: this in wall AP bridge and extend the existing Wifi Signal from router, then PC will
connect with WiFi Repeater as follow:
Attent
ion
wrong connection may damage the device.

5
密级
P4 Wireless Repeater
Wireless Coverage Mode: LAN cable from Switch to in wall AP, then wired networking will change
to Wireless network via Wireless Coverage mode. it suit for hotel, travel, business trip, home
P5 Wireless Coverage Operation mode
Description of LED Status:
LED Status
Woking Status
Flash fast
Networking connecting
Flash slow
Networking connection success
Flash off
Networking connection failure

6
密级
Chapter 2 Run and Login
A. Power this in wallAP in right way
B. Set an IP address for your PC: configure local IP address as 192.168.188.X(X can be selected from
2-254), the same network segment as this access point, subnet mask is 255.255.255.0
P6 IPAddress configure
C. Connect in wallAP with PC by LAN Cable or Wireless
Pls note, if connect in wall with PC by wireless, then the default SSID is Levelone 2.4G, default
passwords are 66666666.
D. Log in: type 192.168.188.253 in your IE, will pop up following picture, pls input admin/admin in User
name/Password to Log into this in wallAP

7
密级
P7 Login
Chapter 3. Operation mode setting
Log into 192.168.188.253 in your Internet Explorer and input user name/Passwords, following device status
will be showed, then you can set this in wallAP as Router/Repeater/AP from Quick Setup:
P8 Device Status
Pls note, if signal strength is blue, mean work fine,

8
密级
if signal strength is red, there is some connection problem.
1. Router operation:
Click Internet Settings, then will see following page, pls choose dynamic IP or PPPOE, then input the user
name, passwords in PPPOE part, after that can change the SSID, Channel, Key as you like, then apply.
P9 Internet Setting
2. Repeater operation:
Click Wireless Repeater, then will see following page:

9
密级
P10 Wireless Repeater
Then scan AP, choose AP, input AP’s passwords to finish the connection setting.
P11 Scan AP
If you want to change this device’s SSID, channel, Key, then set it from Wireless Part. After that, then apply.

10
密级
P12 Internet Setting
3. Wireless Coverage:
click wireless coverage, then will appear following page, change the SSID, Key, Channel as you like, then
apply.

11
密级
P13 Wireless Coverage
After finish the setting, then cancel the IP address you setted for your PC, then the internet setting
is finished.
P14 Obtain IP address automatically

12
密级
Chapter 4 System Tools and Advanced Settings:
1.System Tools
P15 System Tools
In system tools, you can ping any IP address/Domain easy to check the AP’s working status.

13
密级
P16 Advanced Setting
In Advanced Setting, you can set operation mode, SSID, IP address setting, Channel setting, management and
firmware upgrade, let’s show how to upgrade firmware and revert to default.
2. Wireless
In basic setting, you can change the SSID, Region, mode and decide the encryption type and key to SSID.
Intelligent analysis can help you to choose the best channel.
In Virtual AP, you are allowed to use three virtual ap. Please select the SSID first and then enable it. For
instance, i would like to use the VAP1, I should select VAP1 as below and then enable it. After being enabled,
you can configure the details of theAP.After configuration, please apply them.

14
密级
3. Network Setting
In this page, users can set up the basic LAN setting
Under AP Mode, DHCP from Controller means you are allowing the controller to control the IP of the
AP(originally 192.168.188.253) . Therefore the controller can find and manage theAP.

15
密级
When you choose Fixed IP, that means the AP is having the right to decide its own IP instead of being totally
controlled by controller. However, when the IP Address is in the same network segment as controller’s, can the
controller find and manage the AP. Take one for example, when controller’s IP is 192.168.10.1, and only when
AP’s IP is 192.168.10.X can the controller find and manage theAP.
4.Management
4.1 System

16
密级
Press the WPS/Reset button until the LED light off. Click Reset Default from
System.
P18 Reset Default
Backup function allows you to save the current configuration to your PC.
Restore helps you to apply your configuration you saved before in your PC.
Reset Default and Reboot the device just with one click.
4.2 User
Change the user name and password for Log in
4.3 Logs
Logs helps to record the running history of the device which will help you a lot when you have trouble with
this device.You can copy the logs and send it to consult your engineers.

17
密级
4.4 Upgrade Firmware
Browse and choose the firmware should upgrade from above picture, then click upgrade.
After that click Reset Default from System to finish firmware
upgrade
P17 Firmware upgrade
4.5 System Time
In this part, you can set the time of the device. NTP server can only work under Gateway mode. When NTP
server is chosen, Sync with host will be unavailable. When it connects with controller click Sync with Host, it
will get time from controller rather than from PC.
When device running at xx:xx will reboot the device automatically at xx:xx.

18
密级

19
密级
Appendix A LICENSE STATEMENT / GPL
CODE STATEMENT
This product resp. the here
(http://global.level1.com/downloads.php?action=init) for
downloading offered software includes software code developed
by third parties, including software code subject to the GNU
General Public License Version 2 (“GPLv2”) and GNU Lesser
General Public License 2.1 („LGPLv2.1“).
WRITTEN OFFER FOR GPL/LGPL
SOURCE CODE
We will provide everyone upon request the applicable GPLv2 and
LGPLv2.1 source code files via CDROM or similar storage
medium for a nominal cost to cover shipping and media charges
as allowed under the GPLv2 and LGPLv2.1. This offer is valid for 3
years. GPLv2 and LGPLv2 inquiries: Please direct all GPL and
LGPL inquiries to the following address:
Digital Data Communications GmbH
Zeche-Norm-Str. 25
44319 Dortmund
Deutschland
Phone: [phone] - 0

20
密级
Fax: [phone] - 184
Email: [e-mail]
Web: www.level1.com
NO WARRANTY
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE. See the GNU General Public License for more details.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR
ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES
SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF
THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.