LevelOne WAP-6012 User manual

LevelOne
WAP-6012
300Mbps N_Max Wireless Gigabit PoE Access Point
User Manual
V1.0

TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION...................................................................................... 1
Features of your Wireless Access Point ............................................................ 1
Package Contents................................................................................................. 3
Physical Details..................................................................................................... 3
CHAPTER 2 INSTALLATION ....................................................................................... 6
Requirements........................................................................................................ 6
Procedure.............................................................................................................. 6
CHAPTER 3 ACCESS POINT SETUP.......................................................................... 9
Overview................................................................................................................ 9
Setup using a Web Browser.............................................................................. 10
System Basic Settings Screen .......................................................................... 13
System Advanced Settings Screen................................................................... 15
Wireless Screens................................................................................................ 17
Basic Screen ....................................................................................................... 17
Virtual AP Settings.............................................................................................. 19
Virtual AP Screen................................................................................................ 20
Radius Server Settings ...................................................................................... 32
Access Control.................................................................................................... 33
Advanced Settings ............................................................................................. 36
Wi-Fi Protected Setup ........................................................................................ 38
CHAPTER 4 PC AND SERVER CONFIGURATION................................................... 39
Overview.............................................................................................................. 39
Using WEP........................................................................................................... 39
Using WPA-PSK/WPA2-PSK.............................................................................. 40
Using WPA-Enterprise........................................................................................ 41
802.1x Server Setup (Windows 2000 Server)................................................... 42
802.1x Client Setup on Windows XP................................................................. 52
Using 802.1x Mode (without WPA).................................................................... 58
CHAPTER 5 OPERATION AND STATUS .................................................................. 59
Operation............................................................................................................. 59
Status Screen...................................................................................................... 59
CHAPTER 6 ACCESS POINT MANAGEMENT.......................................................... 66
Overview.............................................................................................................. 66
Admin Login Screen........................................................................................... 66
Auto Config/Update............................................................................................ 68
Config File ........................................................................................................... 69
SNMP ................................................................................................................... 71
Log Settings........................................................................................................ 73
Firmware Upgrade.............................................................................................. 75
APPENDIX A SPECIFICATIONS ................................................................................ 76
Wireless Access Point........................................................................................ 76
APPENDIX B TROUBLESHOOTING ......................................................................... 80
Overview.............................................................................................................. 80
General Problems............................................................................................... 80
APPENDIX C WINDOWS TCP/IP............................................................................... 82
Overview.............................................................................................................. 82
Checking TCP/IP Settings - Windows 9x/ME:.................................................. 82
Checking TCP/IP Settings - Windows NT4.0.................................................... 84
Checking TCP/IP Settings - Windows 2000...................................................... 86

Checking TCP/IP Settings - Windows XP......................................................... 88
Checking TCP/IP Settings - Windows Vista..................................................... 90
APPENDIX D ABOUT WIRELESS LANS................................................................... 92
Overview.............................................................................................................. 92
Wireless LAN Terminology................................................................................ 92
APPENDIX E COMMAND LINE INTERFACE ............................................................ 95
Overview.............................................................................................................. 95
Command Reference.......................................................................................... 95
All trademarks and trade names are the properties of their respective owners.

1
Chapter 1
Introduction
This Chapter provides an overview of the Wireless Access Point's fea-
tures and capabilities.
Congratulations on the purchase of your new Wireless Access Point. The Wireless
Access Point links your Wireless Stations to your wired LAN. The Wireless stations
and devices on the wired LAN are then on the same network, and can communicate
with each other without regard for whether they are connected to the network via a
Wireless or wired connection.
Figure 1: Wireless Access Point
Features of your Wireless Access Point
The Wireless Access Point incorporates many advanced features, carefully designed
to provide sophisticated functions while being easy to use.
Standards Compliant. The Wireless Access Point complies with the
IEEE802.11g and IEEE802.11n specifications for Wireless LANs.
Supports 11n Wireless Stations. The 802.11n standard provides for back-
ward compatibility with the 802.11b standard, so 802.11n, 802.11b and 802.11g
Wireless stations can be used simultaneously.
Bridge Mode Support. The Wireless Access Point can operate in Bridge
Mode, connecting to another Access Point. Both PTP (Point to Point) and PTMP
(Point to Multi-Point) Bridge modes are supported.
And you can even use both Bridge Mode and Access Point Mode simulta-
neously!
WPS Support. WPS (Wi-Fi Protected Setup) can simplify the process of con-
necting any device to the wireless network by using the push button configuration
(PBC) on the Wireless Access Point, or entering a 8-digit PIN code if there's no
button.
1

Wireless Access Point User Guide
2
DHCP Client Support. Dynamic Host Configuration Protocol provides a dy-
namic IP address to PCs and other devices upon request. The Wireless Access
Point can act as a DHCP Client, and obtain an IP address and related information
from your existing DHPC Server.
Upgradeable Firmware. Firmware is stored in a flash memory and can be
upgraded easily, using only your Web Browser.
PoE Support. You can use PoE (Power over Ethernet) to provide power to the
Wireless Access Point, so only a single cable connection is required.
Security Features
Virtual APs. For maximum flexibility, wireless security settings are stored in
Virtual AP. Up to 4 Virtual APs can be defined and used as any time.
Multiple BSSIDs.Because each Virtual AP has it own SSID and beacon, and
up to 4 Virtual APs can be active simultaneously, multiple SSIDs are supported.
Different clients can connect to the Wireless Access Point using different SSIDs,
with different security settings.
Virtual APs Isolation.If desired, PCs and devices connecting to different
Virtual APs can be isolated from each other.
VLAN Support. The 802.1Q VLAN standard is supported, allowing traffic from
different sources to be segmented. Combined with the multiple SSID feature, this
provides a powerful tool to control access to your LAN.
WEP support. Support for WEP (Wired Equivalent Privacy) is included. Both 64
Bit 128 Bit, and 152 Bit keys are supported.
WPA support. Support for WPA is included. WPA is more secure than WEP,
and should be used if possible. Both TKIP and AES encryption methods are sup-
ported.
802.1x Support. Support for 802.1x mode is included, providing for the industri-
al-strength wireless security of 802.1x authentication and authorization.
Radius Client Support. The Wireless Access Point can login to your existing
Radius Server (as a Radius client).
Radius MAC Authentication. You can centralize the checking of Wireless
Station MAC addresses by using a Radius Server.
Rogue AP Detection.The Wireless Access Point can detect unauthorized
(Rouge) Access Points on your LAN.
Access Control. The Access Control feature can check the MAC address of
Wireless clients to ensure that only trusted Wireless Stations can use the Wireless
Access Point to gain access to your LAN.
Password - protected Configuration. Optional password protection is
provided to prevent unauthorized users from modifying the configuration data and
settings.
Advanced Features
Command Line Interface. If desired, the command line interface (CLI) can be
used for configuration. This provides the possibility of creating scripts to perform
common configuration changes.
Auto Configuration. The Wireless Access Point can perform self-configuration
by copying the configuration data from another Access Point. This feature is
enabled by default.

Introduction
3
Auto Update. The Wireless Access Point can automatically update its firmware,
by downloading and installing new firmware from your FTP server.
Radius Accounting Support. If you have a Radius Server, you can use it to
provide accounting data on Wireless clients.
Syslog Support. If you have a Syslog Server, the Wireless Access Point can
send its log data to your Syslog Server.
SNMP Support. SNMP (Simple Network Management Protocol) is supported,
allowing you to use a SNMP program to manage the Wireless Access Point.
Package Contents
The following items should be included:
Wireless Access Point
Power Adapter
Quick Start Guide
CD-ROM containing the manual.
If any of the above items are damaged or missing, please contact your dealer imme-
diately.
Physical Details
Front Panel LEDs
Figure 2: Front Panel
Power
On - Normal operation.
Off - No power

Wireless Access Point User Guide
4
WLAN
On - Idle
Off - Wireless connection is not available.
Flashing - Data is being transmitted or received via the Wireless
access point. Data includes "network traffic" as well as user data.
Status
On - Error condition.
Off - Normal operation.
Blinking - During start up, and when the Firmware is being up-
graded.
Ethernet
On - The LAN (Ethernet) port is active.
Off - No active connection on the LAN (Ethernet) port.
Flashing - Data is being transmitted or received via the correspond-
ing LAN (Ethernet) port.

Introduction
5
Rear Panel
Figure 3: Rear Panel
Reset Button
This button has two (2) functions:
Reboot. When pressed and released, the Wireless Access
Point will reboot (restart).
Reset to Factory Defaults. This button can also be used to
clear ALL data and restore ALL settings to the factory default
values.
To Clear All Data and restore the factory default values:
1. Hold the Reset Button until the Status (Red) LED blinks
TWICE, usually more than 5 seconds.
2. Release the Reset Button.
The factory default configuration has now been restored, and
the Access Point is ready for use.
LAN
Use a standard LAN cable (RJ45 connectors) to connect this
port to a 10/100/1000BaseT hub/switch on your LAN.
Power port
Connect the supplied power adapter (12V@1A) here.

6
Chapter 2
Installation
This Chapter covers the physical installation of the Wireless Access
Point.
Requirements
Requirements:
TCP/IP network
Ethernet cable with RJ-45 connectors
Installed Wireless network adapter for each PC that will be wirelessly connected to
the network
Procedure
1. Select a suitable location for the installation of your Wireless Access Point. To
maximize reliability and performance, follow these guidelines:
Use an elevated location, such as wall mounted or on the top of a cubicle.
Place the Wireless Access Point near the center of your wireless coverage
area.
If possible, ensure there are no thick walls or metal shielding between the
Wireless Access Point and Wireless stations. Under ideal conditions, the
Wireless Access Point has a range of around 150 meters (450 feet). The
range is reduced, and transmission speed is lower, if there are any obstruc-
tions between Wireless devices.
2

Installation
7
Figure 4: Installation Diagram
2. Use a standard LAN cable to connect the "LAN" port on the Wireless Access Point
to a 10/100/1000BaseT hub/switch on your LAN.
3. Connect the supplied power adapter to the Wireless Access Point and a conve-
nient power outlet, and power up.
4. Check the LEDs:
The Status LED should flash, then turn OFF.
The Power, Ethernet and WLAN LEDs should be ON.
For more information, refer to Front Panel LEDs in Chapter 1.
Using PoE (Power over Ethernet)
The Wireless Access Point supports PoE (Power over Ethernet). To use PoE:
5. Do not connect the supplied power adapter to the Wireless Access Point.
6. Connect one end of a standard (category 5) LAN cable to the Ethernet port on the
Wireless Access Point.
7. Connect the other end of the LAN cable to the powered Ethernet port on a suitable
PoE Adapter. (24V DC, 500mA)
8. Connect the unpowered Ethernet port on the PoE adapter to your Hub or switch.
9. Connect the power supply to the PoE adapter and power up.
10. Check the LEDs on the Wireless Access Point to see it is drawing power via the
Ethernet connection.

Wireless Access Point User Guide
8
Figure 5: Using PoE (Power over Ethernet)

9
Chapter 3
Access Point Setup
This Chapter provides details of the Setup process for Basic Operation
of your Wireless Access Point.
Overview
This chapter describes the setup procedure to make the Wireless Access Point a valid
device on your LAN, and to function as an Access Point for your Wireless Stations.
Wireless Stations may also require configuration. For details, see Chapter 4 - PC and
Server Configuration.
The Wireless Access Point can be configured using your Web Browser
3

Wireless Access Point User Guide
10
Setup using a Web Browser
Your Browser must support JavaScript. The configuration program has been tested
on the following browsers:
Internet Explorer V4 or later
Netscape V4.08 or later
Setup Procedure
Before commencing, install the Wireless Access Point in your LAN, as described
previously.
1. Check the Wireless Access Point to determine its Default Name. This is shown on
a label on the base or rear, and is in the following format:
WAP-6012
2. Use a PC which is already connected to your LAN, either by a wired connection or
another Access Point.
Until the Wireless Access Point is configured, establishing a Wireless connec-
tion to it may be not possible.
If your LAN contains a Router or Routers, ensure the PC used for configura-
tion is on the same LAN segment as the Wireless Access Point.
3. Start your Web browser.
4. In the Address box, enter "HTTP://" and the IP Address of the 11N Wireless
Access Point, as in this example, which uses the Wireless Access Point's default
IP Address:
HTTP://192.168.1.1
5. You should then see a login prompt, which will ask for a User Name and Password.
Enter admin for the User Name, and admin for the Password.
These are the default values. The password can and should be changed. Always
enter the current user name and password, as set on the Admin Login screen.
User Name: admin
Password: admin
Figure 6: Password Dialog

Access Point Setup
11
6. You will then see the Status screen, which displays the current settings and status.
No data input is possible on this screen. See Chapter 5 for details of the Status
screen.

Wireless Access Point User Guide
12
7. From the menu, check the following screens, and configure as necessary for your
environment. Details of these screens and settings are described in the following
sections of this chapter.
System - Basic and Advanced settings
Wireless - Basic, Advanced, Access Control, Radius Server, Virtual APs &
WIFI Protected Setup.
8. You may also wish to set the admin password and administration connection
options. These are on the Admin Login screen accessed from the Management
menu. See Chapter 6 for details of the screens and features available on the
Management menu.
9. Use the Apply and Reboot buttons on the menu to apply your changes and restart
the Wireless Access Point.
Setup is now complete.
Wireless stations must now be set to match the Wireless Access Point. See Chapter 4
for details.
If you can't connect:
It is likely that your PC’s IP address is incompatible with the Wireless
Access Point’s IP address. This can happen if your LAN does not have a
DHCP Server.
The default IP address of the Wireless Access Point is 192.168.1.1, with a
Network Mask of 255.255.255.0.
If your PC’s IP address is not compatible with this, you must change your
PC’s IP address to an unused value in the range 192.168.1.50 ~
192.168.1.200, with a Network Mask of 255.255.255.0. See Appendix C -
Windows TCP/IP for details for this procedure.

Access Point Setup
13
System Basic Settings Screen
Click Basic Settings on the System menu to view a screen like the following.
Figure 7: System Basic Settings Screen
Data - System Basic Settings Screen
Identification
Access Point
Name
Enter a suitable name for this Access Point.
Description
If desired, you can enter a description for the Access Point.
Country Do-
main
The country or domain which is matching your current location.
MAC Address
The MAC address is displayed.
IP Settings
DHCP Client
Select this option if you have a DHCP Server on your LAN, and
you wish the Access Point to obtain an IP address automatically.

Wireless Access Point User Guide
14
Fixed IP Ad-
dress
If selected, the following data must be entered.
IP Address - The IP Address of this device. Enter an unused
IP address from the address range on your LAN.
Subnet Mask - The Network Mask associated with the IP
Address above. Enter the value used by other devices on
your LAN.
Gateway - The IP Address of your Gateway or Router. Enter
the value used by other devices on your LAN.
DNS - Enter the DNS (Domain Name Server) used by PCs
on your LAN.
DHCP Server
If Enabled, the Access Point will allocate IP Addresses to
PCs (DHCP clients) on your LAN when they start up. The de-
fault (and recommended) value is Enabled.
The Start IP Address and Finish IP Address fields set the
values used by the DHCP server when allocating IP Ad-
dresses to DHCP clients. This range also determines the
number of DHCP clients supported.
Wins Server
Name/IP Ad-
dress
Enter the server name or IP address of the Wins Server.
TimeZone
TimeZone
Choose the Time Zone for your location from the drop-down list.
If your location is currently using Daylight Saving, enable the
Adjust for
Daylight Saving Time checkbox.
You must UNCHECK this checkbox when Daylight Saving
Time finishes.
NTP Server
Name/IP Ad-
dress
Enter the server name or IP address of the NTP.

Access Point Setup
15
System Advanced Settings Screen
Click Advanced Settings on the System menu to view a screen like the following.
Figure 8: System Advanced Settings Screen
Data - System Advanced Settings Screen
VLAN
Enable 802.1Q
VLAN
This option is only useful if the hubs/switches on your LAN
support the VLAN standard.
Native VLAN
Enter the desired value for the Native VLAN. Default value is 1.
AP Manage-
ment VLAN
Define the VLAN ID used for management.
VLAN List
Define the unique ID value (1 - 4094) for each VAP.
Network Integrality Check
Enable Net-
work Integrality
Check
If enabled, the AP will disable the wireless connection if the wired
connect of AP is invalid.
LLTD
Enable Link
Layer Topology
Discovery
Enable this if you want to use Link Layer Topology Discovery
protocol (LLTD) feature.
STP
Enable Span-
ning tree
Protocol
Enable this if you want to use this feature.
802.1x Supplicant
Enable 802.1x
Supplicant
Enable this if your network requires this AP to use 802.X authen-
tication in order to operate.

Wireless Access Point User Guide
16
Authentication
Authentication via MAC Address
Select this if you want to Use MAC Address for Authentica-
tion.
Authentication via Name and Password
Select this if you want to Use name and password for Au-
thentication.
Bonjour
Zero-configuration networking, enables automatic discovery
of computers, devices, and services on IP networks using
industry standard IP protocols