Leviton GreenMax OSR05-IC Series User manual

CAUTIONS:
• ESD Sensitive Device: Use safe handling procedures when installing.
• For indoor applications ONLY.
Before Installation
• Requires installation into a 2 7/8 in. to 3 1/4 in. diameter (73.03 mm to
82.55 mm) mounting hole.
• Requires 4 in. (102 mm) of vertical clearance.
• When installation requires conduit for Class 2 LumaCAN wiring, drill a
2 7/8 in. opening into the side of the junction box, and install the junction
box in the ceiling, directly above the sensor.
• LumaCAN wiring requires a Category-rated cable for power and data.
Use Category 6 or better cable with quality RJ-45 connections. Wire
per TIA-568B standards.
• For compliance with Chicago Plenum requirements, install in a metal box
in the ceiling. See the 3rd bullet point above.
• All LumaCAN wire segments must be tested and validated prior to
powering up the system.
• The end of each LumaCAN network must be terminated for proper data
flow. A termination plug is pre-installed into one of the RJ-45 receptacles. If
this is the end of the network, only one of the RJ-45 receptacles are used.
Leave the termination plug in the unused RJ-45 receptacle. If this is in the
middle of the network, both RJ-45 receptacles are required. Remove and
discard the termination plug.
GreenMax®DRC Sensor
Cat. No. OSR05-ICx
INSTALLATION INSTRUCTIONS ENGLISH
DI-000-OSR05-00C
Specifications
Input Voltage +12-24VDC, 70-35mA
IP Rating IP30
Network
Connections
• (2) RJ-45 Cat. 6 or better to connect to a
LumaCAN network.
• 1,600’ maximum length per Daisy-Chain Segment.
• Home-Run topology supported when using
repeaters, which may extend the network's length.
NOTE: Pass-Through RJ-45 connectors are prohibited
from use. Use of these connectors, voids all warranties,
and any promise of product suitability of operation.
Operating
Temperature
32°F to 131°F (0°C to 55°C),
0% to 85% relative humidity
Storage
Temperature 14°F to 185°F (-10°C to 85°C)
Sensor Range 450 sq. ft.
Sensor Technology PIR + Photocell
Warm-Up Time 15 seconds
Product Description
The GreenMax DRC Sensor is a direct network-connected device, which
can detect both Occupancy and Light levels within a specified range. It
reports data with LumaCAN™ Sensor messages over the network for
receipt by any Sapphire or GreenMAX DRC Room Controller.
Reference
A. LumaCAN Connections
B. Reset Switch - Push and hold down for 5 seconds to reset the
sensor's settings to their factory default settings.
For Application Reset: If your device is "bricked" and you power
up the device by pushing and holding down the reset switch for 10
seconds, the current application is deleted. As a result, the device
becomes inoperable, and you must perform a software update.
C. LumaCAN Communication Indicator Light - Normal Operation: Stays
solid Green when there is power, but no communication. Blinks Green
when communicating.
D. Occupancy Detector, Light Level Sensor, and Occupancy
Indicator Light:
• Blinks Red when PIR detects occupancy.
• Blinks Green when the photocell detects occupancy.
• Blinks White rapidly when a firmware update is in process.
• Blinks White slowly when in boot loader.
• Cycles colors when an address assignment is pending from a DRC
or other compatible controller.
A
C
D
WARNINGS:
• TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT
BREAKER OR FUSE, AND TEST THAT THE POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are not sure about any part of these instructions, consult an electrician.
Occupancy Sensor Technology and Application Notes:
• The OSR05-ICx sensor uses PIR (Passive InfraRed) detection
technology. This technology uses a lens to establish dozens of detection
zones. The sensor is sensitive to the heat emitted by the human body. To
trigger the sensor, the source of the heat must move from one detection
zone to another. The device is effective in sensing motion across its field-
of-view, and be conscientious of this when you select an
installation location.
• Occupancy sensors respond to rapid changes in temperature, and hot or
cold drafts look like body motion to the device if it mounted to close to a
climate control source. Make sure to mount this device approximately
6 ft away from a climate control source, such as radiators, air exchanges,
and air conditioners.
• Do NOT mount the Occupancy Sensor directly under a high-wattage light
source. High-wattage bulbs (greater than 100 W incandescent) give off a
lot of heat and switching the bulb may cause a temperature change that
can be detected by the device. Mount the Occupancy Sensor at least 6 ft
away. If you must mount the device closer, lower the bulb's wattage.
B
WEB VERSION

© 2022 Leviton Mfg. Co., Inc.
4. Confirm the sensor is operating on the network.
5. Install the sensor into the mounting hole.
a. Retract spring arms and
insert into mounting hole. b. Push down the spring arms to secure the sensor.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
SDoC STATEMENT
Model OSR05-ICW, manufactured by Leviton Manufacturing, Inc., 201 N. Service Road, Melville, NY 11747, leviton.com.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Any changes or modifications not expressly approved by Leviton Manufacturing Co., could void the user’s authority to operate the equipment.
3. LumaCAN Address: This device receives a LumaCAN address from a DRC controller or other compatible device. The sensor's indicator displays a
multi-color LED pattern when the device is installed, has power, but does not have a LumaCAN address yet.
NOTE: The assignment of a LumaCAN address by a controller can take up to 15 minutes after the device powers up.
For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper
use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty
excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a
particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment,
lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the
Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1-800-405-5320.
1. Drill a mounting hole approximately 2 7/8 in. to 3 1/4 in. (73.03 mm to 82.6 mm) in diameter.
Installation
2. Push network wires through hole, and connect them to the sensor. If end of line, terminate the sensor with the provided RJ-45 termination plug.
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF POWER AT CIRCUIT BREAKER OR FUSE, AND TEST THAT THE POWER IS OFF BEFORE WIRING!
Patents covering this product, if any, can be found on www.leviton.com/patents.
WEB VERSION