Leviton DMX-512 User manual

Page 1 of 40
User Guide
Leviton Remembrance Control Stations
REMEMBRANCE
DMX-512 AND ANALOG CONTROL STATIONS
USER GUIDE
Copyright®2004
Leviton Manufacturing Co., Inc.
DI-00X-RMB81-00A

Page 2 of 40
User Guide
Leviton Remembrance Control Stations

Page 3 of 40
User Guide
Leviton Remembrance Control Stations
Table of Contents
System Overview ..................................................................................................................... 5
Remember When … ....................................................................................................................................5
Welcome Back to Simplicity. ........................................................................................................................5
What experience is Prerequisite? ................................................................................................................5
What is needed? ..........................................................................................................................................5
What is not needed? ....................................................................................................................................6
Control Station Operation .......................................................................................................7
Play Mode ....................................................................................................................................................7
DMX Snapshot Record Mode ......................................................................................................................7
Record Example:..........................................................................................................................................8
DMX Channel Mode .....................................................................................................................................9
Component Functions ........................................................................................................... 10
Take control PCB .......................................................................................................................................10
2 Channel Analog Fader PCB ....................................................................................................................10
ANA-2-DMX Scene Processor PCB...........................................................................................................10
System Design Considerations ............................................................................................ 11
Place HHR or DMX-512 IN jacks near DMX stations.................................................................................11
Power Supply Requirements...................................................................................................................... 11
Current Calculation Examples:...................................................................................................................12
System Cable Requirements................................................................................................. 13
Cross Referenced Analog Compatible Cable Types: .................................................................................13
Cable Derating Requirements: ...................................................................................................................13
Eliminate Ground Loops ....................................................................................................... 14
What is ground? .........................................................................................................................................14
Keep COM and GND separate. .................................................................................................................14
Make star or daisy chain connections. .......................................................................................................14
DMX daisy-chain configuration rules:.........................................................................................................14
DMX bridge rules: ......................................................................................................................................14
Advanced topics..................................................................................................................... 15
Use of blocking (steering) Diodes. .............................................................................................................15
Addendum .............................................................................................................................. 16
Wiring Details .............................................................................................................................................16
Jumper Settings .........................................................................................................................................16
Preset Station DMX-512 Snapshot Record Procedure ..............................................................................17

Page 4 of 40
User Guide
Leviton Remembrance Control Stations
Sample System Configurations ............................................................................................ 18
Multi-Purpose Room With A/V Control Booth.............................................................................................18
Small Church (All Analog Stations) ............................................................................................................19
Theater With Houselights / Rehersal Lights ...............................................................................................20
Dual DMX-512 Bridge ................................................................................................................................21
Wiring Diagrams..................................................................................................................... 22
1 Channel Analog Station (Cat. No. 001-RMB81-001)...............................................................................22
2 Channel Analog Station (Cat. No. 002-RMB81-002)...............................................................................23
3 Channel Analog Station (Cat. No. 003-RMB81-003)...............................................................................24
4 Channel Analog Station (Cat. No. 004-RMB81-004)...............................................................................25
5 Channel Analog Station (Cat. No. 005-RMB81-005)...............................................................................26
6 Channel Analog Station (Cat. No. 006-RMB81-006)...............................................................................27
8 Channel Analog Station (Cat. No. 007-RMB81-008)...............................................................................28
10 Channel Analog Station (Cat. No. 008-RMB81-010).............................................................................29
12 Channel Analog Station (Cat. No. 009-RMB81-012).............................................................................30
Entry Station (Cat. No. 010-RMB81-021)...................................................................................................31
Panic Station (Cat. No. 011-RMB81-022) ..................................................................................................32
4 Channel DMX-512 Station (Cat. No. 017-RMB81-104) ..........................................................................33
6 Channel DMX-512 Station (Cat. No. 018-RMB81-106) ..........................................................................34
12 Channel DMX-512 Station (Cat. No. 019-RMB81-112) .........................................................................35
0-10V Analog Dimmer ................................................................................................................................36
Warranty .................................................................................................................................. 38
LIMITED TWO YEAR WARRANTY AND EXCLUSIONS ..............................................................38

Page 5 of 40
User Guide
Leviton Remembrance Control Stations
SYSTEM OVERVIEW
Remember When …
Remember when anyone could add a house light channel or a submaster to a lighting control system by wiring a
slide pot to a diode and attaching it to which ever dimmers they wanted to control? Remember when control
stations could be set up as independents, or group them with masters all without having to have a lap top, memorize
DMX-512, know Windows 95 or battle the great configuration labyrinths envisioned by dyslexic software engineers?
Everything was modular and simple. There was not a central “brain” that required programming, and there was not
the hidden central processor costs and LAN limitations of most conventional architectural control systems.
Welcome Back to Simplicity.
This control system uses 3 small printed circuit board and 2 standard control protocols – DMX-512 and 0-10VDC as
tools to create complex configurations in the simplest and least expensive way.
The three PCB’s are:
•An on/off Take Control card
•A break-away, configurable, 0-10 VDC fader board.
•A 6 Channel 0-10VDC to DMX512 Scene Processor.
What experience is Prerequisite?
The only principles a designer needs to understand is:
•Take Control
•Master
•Slave
•Independent
•Snapshot DMX stream
•Pile-On (highest takes precedence)
Previous experience with 0-10VDC, diode patching and/or DMX-512 control protocols and control wiring is helpful,
but not essential.
What is needed?
•0-10 VDC or DMX-512 Dimmers/Ballast’s
•A DMX-512 Control Console for developing Scenes (DMX stations only)
•A +12to +16 VDC Power Supply orAnalog Stations (This power supply is not required when used in conjunction
with a DMX Station. See page 3 for current requirements)
•10V/5VA bell transformer for DMX Stations (The DMX station will provide 150mA of +V to drive several
Analog Stations).

Page 6 of 40
User Guide
Leviton Remembrance Control Stations
•Standard NEMA Gang Boxes
•Imagination
What is not needed?
•A PC, DOS, Windows. Configuration files, disks or download cables. Station thumbwheel settings, A central
processing cabinet. Lots of patience.

Page 7 of 40
User Guide
Leviton Remembrance Control Stations
CONTROL STATION OPERATION
Play Mode
Action Result
•Press the ON/OFF (Panic) button to The LED will light, indicating the
activate the station. station is active. An Entry or Panic
station will automatically activate a scene.
•Adjust Master Fader if applicable. The Master Fader Proportionally
controls all channel levels.
•Adjust Channel Fader if applicable. Channel Faders may control one
light, a group of lights, or an entire scene.
•Press the ON/OFF (Panic) button to The lights will fade out and the
turn off the lights. LED will turn off.
DMX Snapshot Record Mode
(For DMX control stations only)
Action Result
•Insure JP1 Jumper is out on The remove jumper on JP1 puts the
ANA2DMX Processor Processor in DMX Snapshot mode.
•Insure Record Lock is off. Record Lock disables any attempt to
record scenes, D19 LED on
ANA2DMX Processor will be Orange if able
to record. Green if unable to record.
NOTE
Record Lock can be activated any of 3 ways:
1. Jumper JP1 shorted on 2 Channel Analog PCB on station.
2. Jumper JP2 shorted on ANA2DMX processor on station.
3. REC LOCK terminal on ANA2DMX processor on station driven with external +10VDC signal.

Page 8 of 40
User Guide
Leviton Remembrance Control Stations
•Turn off all control stations. This insures only console levels will
be recorded.
•Bring up the desired scene or look on This is the scene that will be
the main console recorded.
•Go to the DMX control station. This gets the station ready to be put
Slide Master Fader all the way up to full. in record mode.
Slide all the channel faders down to out.
•Push and hold the ON/OFF button when The Green LED will light.
turning the station “ON”
•Count to 5 (approximately 5 seconds) This puts the Station into record
(continue to hold the ON/OFF Button). mode. (LED on ANA2DMX PCB turns green).
•Slide the Channel Fader up to full where This snapshots the DMX-512 data
the scene is to be recorded. (continue to stream, saving the entire scene under
hold the ON/OFF Button). the proportional control of the
channel fader that slid to full. The LED on the
ANA2DMX Processor will blink red when it is
finished recording the scene.
•Release the ON/OFF button. This exits Record Mode.
Record Example:
To record scene into fader 1: (assuming REC LOCK is off)
Action
•Slide master fader to full, channel faders to out.
•Push & hold ON/OFF button when it goes from OFF to ON.
•Count out loud while continuing to hold ON/OFF button:
“One one thousand”
“Two one thousand”
“Three one thousand”
“Four one thousand”
“Five one thousand”
•Slide channel fader 1 to full.
•Release ON/OFF button.

Page 9 of 40
User Guide
Leviton Remembrance Control Stations
DMX Channel Mode
(for DMX control stations only)
Action Result
•Install Jumper JP1 on ANA2DMX PCB. This puts processor in channel mode.
•Dial up the starting address on This selects the DMX start address for
rotary Switches SW1, SW2, & SW3 fader A1.
•For fader channel single pattern Faders 1-6 will respond to DMX channels
operation, remove JP4. 1-6. (assuming start address –001).
•For fader channel dual wraparound Fader 1 controls DMX channels 1 & 7;
Pattern operation, install JP4. Fader 2 controls DMX channels 2 & 8;
Fader 3 controls DMX channels 3 & 9;
Fader 4 controls DMX channels 4 & 10;
Fader 5 controls DMX channels 5 & 11;
Fader 6 controls DMX channels 6 & 12;
(assuming start address = 001)
(and 6 channel operation –see JP6)
•For highest takes precedence fader The fader channel will pile-onto the
operation, remove JP5 appropriate incoming DMX channels.
•To replace the incoming DMX channel The fader channels will replace the
levels with the fader levels, install JP5 appropriate incoming DMX channel levels.
•For 4 channel operation install JP6 on This puts the processor in 4 channel on
ANA2DMX Processor. wraparound mode.
•For 6 & 12 channel operation remove This puts the processor in 6 channel on
JP6 on ANA2DMX Processor. wraparound mode.

Page 10 of 40
User Guide
Leviton Remembrance Control Stations
COMPONENT FUNCTIONS
Take control PCB
The take control PCB has a single switch for ON/OFF operation. The take control PCB requires +12 to +16 Volts
DC 25mA connected across +V and common to operate. The PCB provides a regulated +10.6 VDC source when
the ON/OFF switch is activated (turned on) and O Volts when off.
Pressing the ON/OFF switch sends a +10VDC pulse out the T/C terminal on TB1 and down the T/C wire to reset
any other stations connected to the T/C wire and TB1. The Take Control line determines and connects the stations
you want to respond in a group. Not connecting the take control line makes the stations or groups respond
independently of each other.
When the ON led is lit, +10VDC is available on the VOUT terminal. The VOUT signal can be used to activate a
single analog channel, or when used with prep cable PRP-31316-02, it can be used to activate several channels at
once. The VOUT signal’s most common application is to implement Panic or Entry Stations. See the Wiring Diagrams
for Entry or Panic stations for more details.
2 Channel Analog Fader PCB
The Fader PCB is a breakable PCB array that can be easily be configured for 1-12 channels with or without a
master fader. The input/output bussed connector scheme of J1/P1 passes DC power, analog 0-10V levels, and
take control across the control station to the terminal block on the take control card, or to a header for the ANA-2-
DMX PCB. All 0-10V analog channels are buffered by an op-amp and diode blocked before leaving the PCB.
ANA-2-DMX Scene Processor PCB
The ANA-2-DMX PCB utilizes six 0-10 VDC analog control inputs to proportionally drive 6 DMX submaster scenes
that pile-onto each other and to the incoming DMX signal whether active or inactive. To record a scene, first bring
up the desired look on the console running to the DMX IN terminal. Next, slide the master to full and the channels
to off. Push and hold the ON/OFF button to ON for about 5 seconds on the station, putting the station in record
mode. Finally, slide the fader up to full for the channel you wish to record the scene into. As long as the record
lockout is not enabled, the scene will be saved onto that channel, and will proportionally fade relative to the slide
pot. For user convenience, the record lockout function which disables re-recording scenes is available on the DMX
terminal Block, as a jumper on the ANA-2-DMX PCB itself, and also as a jumper on the 2 channel fader PCB.
Record lock is perfect for setting up house light channels or looks, and then disabling the record function for
patrons. A DMX bypass relay is provided in the event of a power supply failure.

Page 11 of 40
User Guide
Leviton Remembrance Control Stations
SYSTEM DESIGN CONSIDERATIONS
Place HHR or DMX-512 IN jacks near DMX stations
Place a Hand Held Remote Jack from the control console or a DMX-512 IN Jack where the console could be
plugged in near any station that will be used to snapshot scenes on a frequent basis. This way scenes can be
activated from the console in the same place they are to be recorded.
Power Supply Requirements
DMX Station Current Supply:
(+V/COM power supply source for a single station connected to a single 10V/5VA transformer)
Station Type Supply Current Catalog No. # of Gang
4 Channel DMX Station 150mA 017-RMB81-104 4
6 Channel DMX Station 150mA 018-RMB81-106 5
12 Channel DMX Station 100mA 019-RMB81-112 8
12 Channel DMX station connected to qty 2-10V/5VA transformers. (transformers connected to separate
AC1/AC2 inputs) 250ma.
NOTE
The +V/COM current through a DMX station should not exceed 750mA.
Analog Station Current Demands:
+V power supply requirements for a single station (+12 to +16 VDC)
Station Type ON OFF Catalog Bo. # of Gangs
Entry Station 25 mA 5mA 010-RMB81-021 1
Panic Station 25 mA 5mA 011-RMB81-022 1
1 Channel Analog 30 mA 5mA 001-RMB81-001 2
2 Channel Analog 30 mA 5mA 002-RMB81-002 2
3 Channel Analog 35 mA 5mA 003-RMB81-003 4
4 Channel Analog 40 mA 5mA 004-RMB81-004 4
5 Channel Analog 45 mA 5mA 005-RMB81-005 5
6 Channel Analog 50 mA 5mA 006-RMB81-006 5
8 Channel Analog 60 mA 5mA 007-RMB81-008 6
10 Channel Analog 70 mA 5mA 008-RMB81-010 7
12 Channel Analog 80 mA 5mA 009-RMB81-012 8

Page 12 of 40
User Guide
Leviton Remembrance Control Stations
Current Calculation Examples:
3 Grouped Stations
Current demand calculation for qty 3, 6 channel stations connected in a group: T/C connected between stations,
therefore only one station can be on at a time.
+V Amps = 50mA (station 1) + 5mA (station 2) + 5mA (Station 3) = 60mA
3 Independent Stations
Current demand calculation for qty 3, 6 channel stations connected independently; T/C not used. All 3 could be on
at the same time.
+V Amps = 50mA (station 1) + 50mA (station 2) + 50mA (Station 3) = 150mA

Page 13 of 40
User Guide
Leviton Remembrance Control Stations
SYSTEM CABLE REQUIREMENTS
All DMX-512 lines ............................................. Belden # 9829 cable
All Analog lines ................................................. Alpha # 1898/x C cable
1000 feet MAX!! Where x = the # of conductors
All AC1 and AC2 lines ....................................... 18 gauge 600V wire
Cross Referenced Analog Compatible Cable Types:
Belden 8489 (4 conductor)
Belden 8467 (7 conductor)
Belden 8466 (12 conductor)
Belden 8619 (19 conductor) (color code does not match)
National # NQ-418J (4 conductor)
National # NQ-718J (7 conductor)
National # NQ-1018J (10 conductor)
National # NQ-1918J (19 conductor) (color code does not match)
Cable Derating Requirements:
Smaller gauges of multi conductor Alpha wire can be used for short runs with a minimum number of stations if
following list of the criteria is met:
Alpha #1896 (20 gauge conductors) can be used if:
1. The total analog cable length for the system does not exceed 300 Feet. AND
2. The maximum number of stations is 6.
Alpha #1774 thru #1180 (22 gauge conductors) can be used if:
1. The total analog cable length for the system does not exceed 100 Feet. AND
2. The maximum number of stations is 4. AND
3. The maximum number of channels is 6.

Page 14 of 40
User Guide
Leviton Remembrance Control Stations
ELIMINATE GROUND LOOPS
What is ground?
This control system, like most other control systems requires a common reference for the electronics to function
properly. This reference is typically denoted as Common or Ground. Control voltages are measured with respect to
this ground reference, just like the height of a person would normally be measured with respect to the ground they
are standing on. Without a proper common reference, the electronics can not make accurate voltage measurements,
and therefore will not function correctly.
Keep COM and GND separate.
The ANA 2DMX PCB has 2 different control references. COM (Analog Common) and GND (Digital Ground). The
two are nearly the same, except COM is the reference for all the analog control levels and GND (digital ground) is
the reference for the digital electronics and the incoming power supply. COM and GND should never be connected
together with external wiring. Never place This control systems control lines in conduit with other wires, or flickering
problems could occur.
Make star or daisy chain connections.
In this electronics system, it is important for all the COM signals to be connected in a start or daisy-chain configuration,
as opposed to a ring o loop configuration. The reason is that a ring or loop configuration usually acts like a big
antenna which is excited and aggravated by adjacent power lines. Apply the following rules:
DMX daisy-chain configuration rules:
(multiple DMX Stations connected in serial along one DMX-512 line)
1. Do not connect COM between DMX stations.
2. Use a separate power supply for each DMX station.
3. Daisy-chain the DMX-512 signal as normal, connecting the shield drain to DGND.
DMX bridge rules:
(2 or more DMX Stations tied together with COM, each processing its’own DMX-512 line)
1. Tie stations together using COM
2. Use a separate 10V/5VA transformer for each DMX Station
3. Connect the shield drain wire to DGND on the DMX-1 station.
4. Do not connect the shield drain wire to DGND on additional DMX stations (DMX-2, 3, 4 _). Leave the DGND
Terminals or DMX IN/OUT empty. The DMX shield can be passed through the station location, but it should
not touch or connect to anything in the box.

Page 15 of 40
User Guide
Leviton Remembrance Control Stations
ADVANCED TOPICS
Use of blocking (steering) Diodes.
What is a Diode?
A diode is a one-way valve. It allows current to flow in a forward direction, but not in a reverse direction. The input
is the anode, or un-banded end of the part; and the output is the cathode, or banded end of the part. When the input
(anode) is at a voltage potential higher than the output (cathode), current will pass from the input to the output until
it fills up the output connection to nearly the same voltage level as available on the input connection. When the
output voltage rises higher than the input voltage, the part shuts off
Analog Channel Grouping
Use 1N4148 or 1N914 diodes to select multiple Analog Channels to be controlled by a single fader, Entry, or Panic
station. This is done by connecting the banded end (cathode) of the diodes to each of the Analog Channels to be
controlled. Tie the un-banded ends together, and to the single VOUT or A (1-6) single fader control line that is to
control the channels. The diodes will keep the channels to be controlled separate except when the source channel
is active. The 1N4148 or 1N914 is considered a signal diode. It is excellent for quick linear response in low-current
applications, however it has a tendency to fail in high current applications.
Master/Slave Take Control
Un 1N4004 diodes to create Master/Slave take Control relationships between control stations. This is implemented
by attaching the un-banded end (anode) to the master station, and the banded end (cathode) to the slave station(s).
The master station will now be able to take control away from the slave station(s), but the slave station(s) will not be
able to take control away from the master station. The master station will act as an independent from the slave(s)
stations point of view. The slave station will also be unable to record presets if the master station is a DMX station,
as the record operation is a function of the take control circuit. The 1N4004 is considered a rectifier diode, and is
excellent for high-current applications, like the take control circuitry, but it would perform poorly as a signal diode,
because it requires significant current to operate properly.

Page 16 of 40
User Guide
Leviton Remembrance Control Stations
ADDENDUM
Concerning New REMEMBRANCE Preset Stations:
Wiring Details
8 Preset Station: Refer to 8 Channel Analog Station Wiring Diagram and Colortran
(8-1028, 8-1148, 8-1188) Colortran Production Drawings for connection details of this Preset
Station in your specific system.
4 Preset Station: Refer to Colortan Production Drawings for connection
(8-1024, 8-1144) details of this Preset Station in your specific system. Note
the following control wire mapping.
Station Terminal A2 = Preset #1 (usually System A1)
Station Terminal A3 = Preset #2 (usually System A2)
Station Terminal A6 = Preset #3 (usually System A3)
Station Terminal A7 = Preset #4 (usually System A4)
Station Terminal +V = +V for system
Station Terminal COM = COM for system
Station Terminal T/C = T/C as applicable in system design.
NOTE
Connect Station Terminal A1 to Station Terminal A2 on 4 preset
stations to activate Preset 1 on power up.
Jumper Settings
JP3 IN: Enable Snapshot Record feature from this Station DMX-512 Scene
Snapshot Record may be enabled if T/C is connected to recording
processor (either i series e control module, or REMEMBRANCE ANA2DMX
processor). The station will also activate presets, and take control away
from other stations connected to its’T/C line. Refer to Colortan Production
Drawings for connection details, and refer to the snapshot record procedure
below for operational details. The “OFF”LED will stay red while the “OFF”
switch is pressed.
JP3 OUT: Disable Snapshot Record from this station. The station will only activate
presets, and take control away from other stations connected to its’T/C.
Line. The OFF LED will pulse red when the “OFF”switch is pressed.
JP5 IN: Activate Preset 1 on power up. Preset 1 will automatically turn on when
power is applied to the station.
JP5OUT: Activate OFF on power up. All preset will be off when power is applied to
the control station.

Page 17 of 40
User Guide
Leviton Remembrance Control Stations
Preset Station DMX-512 Snapshot Record Procedure
1. JP3 must be installed on this station.
2. Activate DMX-512 scene from control console or DMX-512 portion of control station. On i series e racks, or
i series e Quad racks, a relative fade time for the preset may be assigned by setting DMX channels 511 and
512 to the same control level as follows:
Full = 90 seconds
90% = 9 seconds
80% = 8 seconds
70% = 7 seconds
60% = 6 seconds
50% = 5 seconds
40% = 4 seconds
30% = 3 seconds
20% = 2 seconds
10% = 1 seconds
0% = Instantaneous
3. Turn off all other control sources, so only DMX-512 generated scene is active.
4. Press and hold the “OFF”Button. The “OFF”LED will turn and stay red.
5. Continue pressing the OFF switch for at least 5 seconds. If the preset station is connected to an i series e
rack, the lights will dim when the snapshot mode has been enabled. If the station is connected to anANA2DMX
processor, wait an extra second or two to insure that the processor is in snapshot mode.
6. While holding the OFF switch, press the preset switch where you would like the DMX512 scene stored.
7. Continue to hold the OFF button for another second or until the lights return to their normal levels.
8. Release the OFF button.

Page 18 of 40
User Guide
Leviton Remembrance Control Stations
SAMPLE SYSTEM CONFIGURATIONS
MASTER
ON / OFF
Remembrance
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
COM
+V
T/C
VOUT
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
10VACX
10VACY
REC LOCK
DMX OUT+
DMX OUT-
DGND OUT
DMX IN+
DMX IN-
DGND IN
A
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
B
ROOM 1
3 CHANNEL ANALOG
CAT. NO. 003-RMB81-3
COMBINE ROOMS
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
A
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
B
ROOM 2
CHANNEL ANALOG
CAT. NO. 003-RMB81-3
10V/5VA FXMR
BY OTHERS A/V BOOTH MASTER STATION
12 CHANNEL DMX STATION CAT. NO. 019-RMB81-112
SLAVE STATIONS
LOCKOUT
COMBINE ROOMS
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
A
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
B
ROOM 3
3 CHANNEL ANALOG
CAT. NO. 003-RMB81-3
COMBINE ROOMS
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
A
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
B
ROOM 4
3 CHANNEL ANALOG
CAT. NO. 003-RMB81-3
COMBINE ROOMS
120VAC
CONTROL CONSOLE
DMX-512 BELDEN 9829 BY OTHERS
DMX-512 BELDEN 9829 BY OTHERS
DIMMER
RACK
ROOM 1 ROOM 2
ROOM 4
ROOM 3
A/V BOOTH
AIR WALLS
A
A
A
A
B
B
B
B
NOTE
Use Alpha #1898 wire between
all control stations.
Multi-Purpose Room With A/V Control Booth

Page 19 of 40
User Guide
Leviton Remembrance Control Stations
COM
+V
T/C
VOUT
A1
A2
COM
+V
T/C
VOUT
A1
A2
A3
A4
A5
A6
A7
A8
COM
+V
T/C
VOUT
A1
A2
COM
+V
T/C
VOUT
HOUSE DOWNLIGHTS
VESTIBULE
NSI CAT. NO. N2408
VESTIBULE
ENTRY STATION
CAT. NO. 010-RMB81-21
HOUSE RIGHT
TWO CHANNEL
ANALOG STATION
CAT. NO. 002-RMB81-2
HOUSE LEFT
TWO CHANNEL
ANALOG STATION
CAT. NO. 002-RMB81-2
PODIUM
SANCTUARY WASH
SOLOIST
CHOIR
BABTISMAL
HOUSE CHANDELIER
HOUSE DOWNLIGHTS
VESTIBULE
SANCTUARY (MASTER STATION)
8 CHANNEL ANALOG STATION
CAT. NO. 007-RMB81-8
MASTER
ON / OFF
Remembrance
ON / OFF
Remembrance
ON / OFF
Remembrance
ON / OFF
Remembrance
DMX -
DMX -
DMX +
DMX +
MCPX
MCPX
+ 15V
+ 15V
REM +
REM +
REM -
REM-
1
2
3
4
COM
COM
1
2
3
4
COM
COM
NOTE
Use Alpha #1898 wire between
all control stations.
Small Church (All Analog Stations)

Page 20 of 40
User Guide
Leviton Remembrance Control Stations
MASTER
ON / OFF
Remembrance
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
COM
+V
T/C
VOUT
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
COM
+V
T/C
VOUT
10VACX
10VACY
REC LOCK
DMX OUT+
DMX OUT-
DGND OUT
DMX IN+
DMX IN-
DGND IN
A
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
B
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
3 CHANNEL ANALOG STATIONS
CAT. NO. 003-RMB81-3
HOUSELIGHT
STATIONS
3 ENTRY STATIONS
CAT. NO. 010-RMB81-21
ENTRY (CLEANING)
STATIONS
10V/5VA FXMR
BY OTHERS
CONTROL BOOTH
12 CHANNEL DMX STATION
CAT. NO. 019-RMB81-112
REHERSAL
LIGHTS HOUSE
LIGHTS
ENTRY
ENTRY STATION
CAT. NO. 010-RMB81-21
HOUSELIGHT /
ENTRY STATIONS
LOCKOUT
HOUSELIGHT /
ENTRY STATIONS
LOCKOUT
120VAC
CONTROL CONSOLE
DMX-512 BELDEN 9829 BY OTHERS
DMX-512 BELDEN 9829 BY OTHERS
DIMMER
RACK
ON / OFF
Remembrance
MASTER
ON / OFF
Remembrance
COM
+V
T/C
VOUT
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
COM
+V
T/C
VOUT
STAGE MANAGERS PANEL
12 CHANNEL ANALOG STATION
CAT. NO. 019-RMB81-112
ENTRY STATION
CAT. NO. 010-RMB81-21
ON / OFF
Remembrance
COM
+V
T/C
VOUT
B
ON / OFF
Remembrance
COM
+V
T/C
VOUT
B
ON / OFF
Remembrance
COM
+V
T/C
VOUT
B
ON / OFF
Remembrance
Theater With Houselights / Rehearsal Lights
NOTE
Use Alpha #1898 wire between
all control stations.