1. How to change the settings.
For Technical Assistance Call: 1-800-824-3005 (USA Only)
or 1-800-405-5320 (Canada Only) www.leviton.com PK-A3346-10-00-2A-X4
© 2020 Leviton Mfg. Co., Inc.
What to do if...
Issue Make this adjustment
Lights do not operate with push pad and RED indicator does not
blink when motion is present • Verify wiring connections to sensor.
Lights do not switch ON when motion is detected - DOS05
• Motion is beyond sensing range - move closer to switch.
• Adjust the light level lower (Option 3, 2, 1 or disable).
• The RED light will blink to indicate motion. If it is blinking and the load is not turning ON, it could be due to ambient light OR it check to
make sure that the Occ-Vac switch is in OCC position.
Lights always stay ON
• Check time delay settings and compare to how long the lights stay ON.
• Make sure no motion occurs in coverage area for time selected by covering the lens.
• Check that switch is not installed near a heat source (like stove, lights, heat vents) or detecting motion from an adjacent area (like
hallway traffic) and if it is, relocate it.
Lights do not turn ON - DVS05
• Make sure that control is installed correctly.
• Make sure the power is ON.
• Check to make sure the light bulb is functional.
FCC STATEMENT: This device complies with Part 15 of the FCC Rules. Operation is subject to following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving Antenna. • Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/tv technician for help.
FCC CAUTION: Any changes or modifications not expressly approved by Leviton Manufacturing Co., Inc., could void the user's authority to operate the equipment.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec),
Canada H9R 1E9 or by telephone at 1-800-405-5320.
LIMITED 5 YEAR WARRANTY For Leviton’s limited product warranty, go to www.leviton.com. For a printed copy of the warranty,call 1-800-824-3005.
Patents covering this product, if any, can be found on www.leviton.com/patents.
Leviton and Block and Design logo is a registered trademark and Decora is a trademark of Leviton Mfg. Co., Inc.
Sensing Area Coverage
1. Horizontal field of view:
2. Vertical field of view:
3. Using advanced modes.
10 FT
0
10 FT
15 FT
20 FT
30 FT
Horizontal Beam Diagram
Major motion coverage 900ft2
Minor motion coverage 400ft2
15 FT
10 FT
40-48 IN
0
10 FT
15 FT
20 FT
20 FT 30 FT
30 FT
Horizontal Beam Diagram
Major motion coverage 900ft2
Minor motion coverage 400ft2
40-48 IN
20 FT
30 FT
30 FT
Horizontal Beam Diagram
Major motion coverage 900ft2
Minor motion coverage 400ft2
Mode name To enable this mode... The device will...
Test Mode
Press and hold TOP of button for 5
seconds. To exit, press TOP or BOTTOM
of button or it will automatically exit after
2 minutes.
Turn on the load for 5 seconds every
time motion is detected. RED light
will blink 1x/2 sec when in Test Mode.
Locator LED function is disabled while
motion detection function is active.
Temporary Bypass
Mode (Available for
occupancy sensors only)
Press and hold BOTTOM of button for 5
seconds. To exit, press TOP or BOTTOM
of button.
Ignore motion keeping the light/load off.
GREEN light will double flash every 2
seconds.
Programming Mode
(See Programming
directions below)
Hold TOP and BOTTOM of button for
5 seconds.
GREEN light will be solid ON for
5 seconds. NOTE: if nothing happens,
device is already in programming mode.
Occupancy/Vacancy Switch (DOS05 only)
Remove color kit and wallplate to access.
2. When to use occupancy or vacancy.
Modes When to use
this setting Time Amount of Ambient
Light Present
Turns light
ON when...
Light turns OFF
when...
Occupancy
(DOS05
only)
When automatic
ON/OFF lighting
control is desired.
Any 1.
Low - Light will turn
ON automatically if
room is darkest.
2.
Medium - Light
will turn ON
automatically if room
has more light.
3.
High - Light will turn
ON automatically if
room has the most
light.
4.
Disabled - Light will
turn ON always.
User walks into the
view of the sensor
when the light is
OFF and it is darker
than the ambient
light level set.
OR
TOP or BOTTOM of
button is pushed.
No motion is detected
for the duration of the
programmed time period.
OR
TOP or BOTTOM of
button is pushed.
Vacancy When Manual
ON, Automatic
OFF lighting
control is desired.
Any N/A TOP or BOTTOM of
button is pushed.
OR
User moves around
within 30 secs of the
light turning OFF.
TOP or BOTTOM of
button is pushed.
OR
No motion is detected
for the duration of the
programmed time period.
How to choose a setting and option
In order to... Do this... Indicator light will...
Enter programming mode Hold TOP and BOTTOM button for
5 seconds
GREEN light will be solid ON for 5 seconds.
NOTE: if nothing happens, device is already in
programming mode
Change settings (Timer,
Sensitivity, Ambient Light)
Single press TOP button = advance
to the next setting (see table below)
RED light will blink to indicate column selected
(Timer ->Sensitivity ->Ambient Light ->Timer)
(Example: Column 1 = 1 blink/sec)
Change options within a
setting
Single press BOTTOM button =
advance to the next option
(see table below)
GREEN light will blink to indicate option selected
Examples: Option 1 = 1 blink/sec
Option 2 = 2 blinks/sec
Save and exit settings Hold either TOP or BOTTOM button
for 5 seconds GREEN light will be solid ON for 5 seconds
NOTE: If there is no activity for 30 seconds, the device will automatically exit programming mode and
setting changes will not be saved. Multiple settings can be saved by entering the programming settings
once, selecting desired settings and then save and exit.
Setting Types and Options (defaults are in bold)
Option
Number
Column 1 Column 2 Column 3
TIMER
(Duration of time for
which load is ON since
last detected motion)
SENSITIVITY
(Sensitivity to motion –
adjusting the major and minor
detection range.)
DOS05 ONLY -
AMBIENT LIGHT
(If the room is brighter than the setting
selected, the load will not turn ON.)
Option 1 1 minute Low (50% Range) Low Light level
Option 2 5 minutes Medium Medium Light level
Option 3 10 minutes High High/Brightest light level
Option 4 20 minutes All settings to default Disabled – turns ON for all light levels
Operation
RED indicator light
(Will flash any time
motion is detected)
TOP of button
GREEN locator/
indicator light
(Turns ON when
load is OFF)
OCC
VAC
Changing your device color
Remove Replace
VAC
VAC
NOTE: Press either
TOP or BOTTOM of
button to turn ON/OFF.
BOTTOM of button
Programming
