Leviton VerifEye 7000 Series User manual

Advanced Multi-Circuit Meter 7000/7100 Series
User's Guide
Cat. Nos. 71D12, 71D48, 70D12, 70D48, 70N12, 70N48,
71D24, 70D24, 70N24, 71D03, 70D03
PK-A3259-10-00-0D
Cat. 71D24 and 71D48Cat. 71D12
Cat. 70D48
Cat. 70D12
VerifEye®
Cat. 71D03
Cat. 70D03
Cat. 70D24
WEB VERSION

WEB VERSION

1 Warnings and Cautions .....................................................................4
2 Introduction ........................................................................................6
3 Planning for Field Installation ...........................................................9
4 Meter Conguration ......................................................................... 11
5 Meter Installation..............................................................................23
6 Communication & Verication ........................................................36
7 RTU Programming & Scripting........................................................48
8 Appendix A: LCD Menu Navigation ................................................62
9 Appendix B: Technical Specications............................................65
10 Standard Statements and Warranty................................................67
TABLE OF CONTENTS
WEB VERSION

44
WARNINGS:
• HAZARD OF ELECTROCUTION, SHOCK, EXPLOSION, OR ARC FLASH.
CAREFULLY READ AND FOLLOW INSTRUCTIONS.
• TO AVOID FIRE, SHOCK OR DEATH, turn OFF all power supplying equipment before
working on or inside the equipment. Use a properly rated voltage sensing device to
conrm power is OFF.
•
Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• This equipment MUST be installed and serviced by an electrician or other qualied
personnel with the requisite knowledge, training and experience related to the
installation and operation of this equipment.
• Product may use multiple voltage/power sources. Be sure all sources of power have
been disconnected before servicing.
• Do not depend on this product for voltage indication.
• Only install this product on insulated conductors.
• If the meter appears damaged or defective, rst disconnect all power to the meter. Then
call or e-mail technical support for assistance.
DO NOT EXCEED 346V Line to Neutral (L-N) or 600V Line to Line (L-L). This meter is
equipped to monitor loads up to 346V L-N. Exceeding this voltage will cause damage to
the meter and danger to the user. Always use a Potential Transformer (PT) for voltages in
excess of 346V L-N or 600 volts L-L. VerifEye®branded meters are 600 Volt Over Voltage
Category III devices.
For use in a Pollution Degree 2 or better environment only. A Pollution Degree 2
environment must control conductive pollution and the possibility of condensation or
high-humidity. Consider the enclosure, the correct use of ventilation, thermal properties
of the equipment, and the relationship with the environment.
Installation category: CAT II or CAT III.
Provide a disconnect device to disconnect the meter from the supply source. Place
this device in close proximity to the equipment, within easy reach of the operator, and
mark it as the disconnecting device. The disconnecting device must meet the relevant
requirements of IEC 60947-1 and IEC 60947-3, and be suitable for the application. In the
US and Canada, disconnecting fuse holders can be used. Provide over-current protection
and disconnecting device for supply conductors with approved current-limiting devices
suitable for protecting the wiring. If the equipment is used in a manner not specied by
the manufacturer, the protection provided by the device may be impaired.
1 WARNINGS AND CAUTIONS
WEB VERSION

5
CAUTIONS:
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classied locations.
• The installer is responsible for compliance with all applicable codes.
• Mount this product inside a suitable re and electrical enclosure.
• If the collector is connected directly to a source of voltage, the pulse isolator burns out
immediately and becomes non-responsive.
• Do no use any cleaning agents, including water, on the device.
• No accessories are approved for use with the meter other than those specied in the
Leviton Manufacturing product literature and price sheets.
• A circuit breaker used as a disconnect must meet the requirements of IEC 60947-1 and
IEC 60947-3 (Clause 6.11.4.2).
• Current transformers may not be installed in equipment where they exceed 75 percent
of the wiring space of any cross-sectional area within the equipment.
•
Current transformers may not be installed in an area where they block ventilation openings.
• Current transformers may not be installed in an area of breaker arc venting.
• Not suitable for Class 2 wiring method nor intended for connection to Class 2 equipment.
• Secure current transformer and route conductors so that they do not directly contact live
terminals or bus.
• External secondary inputs and outputs should be connected to devices meeting the
requirements of IEC 60950.
• The following additional requirements apply for recognized board versions of the
VerifEye®meter:
• For use only with listed energy-monitoring current transformers.
• Associated leads of the current transformers shall be maintained within the same
overall enclosure.
• Unless the current transformers and their leads have been evaluated for
REINFORCED INSULATION, the leads must be segregated or insulated from
different circuits.
• The current transformers are intended for installation within the same enclosure as the
equipment. These may not be installed within switch gears and panel boards
or similar.
• Use this device with copper or copper-clad wire only.
• For indoor use only.
1 WARNINGS AND CAUTIONS
WEB VERSION

6
The VerifEye®7000 Series and the VerifEye®7100 Series meters monitor the voltage,
current, power, energy, and many other electrical parameters on single and three-phase
electrical systems. A VerifEye®meter uses direct connections to each phase of the
voltage and current transformers to monitor each phase of the current. Information on
energy use, demand, power factor, line frequency, and more are derived from these
voltage and current inputs.
Each of these meters are not meant to be standalone energy recorders; rather they
are connected as slave devices to a data logger, Remote Terminal Unit (RTU), or
Building Management host network. The VerifEye®meter communication interfaces
include Ethernet (LAN), or RS-485 serial. BACnet MS/TP and Modbus RTU are the two
communication protocols that operate over an RS-485 serial network and BACnet IP and
Modbus TCP are supported over Ethernet. A USB port is also provided as the preferred
connection for on-site conguration and can be run concurrently with an RTU.
2.1 Unpacking the Unit
You can order the VerifEye®meters with optional product features, which are
identiable on the part number label.
VerifEye®Part Numbering Scheme
70D48-000 Series 7000 Embedded Branch Circuit Monitor, Mounting Plate, 48 Input,
with LCD Display
70N48-000 Series 7000 Embedded Branch Circuit Monitor, Mounting Plate, 48 Input,
with no display
71D48-000 Series 7100 Branch Circuit Monitor, Plastic Enclosure, 48 Input, with
LCD Display
70D24-000 Series 7000 Embedded Branch Circuit Monitor, Mounting Plate, 24 Input,
with LCD Display
70N24-000 Series 7000 Embedded Branch Circuit Monitor, Mounting Plate, 24 Input,
with no display
71D24-000 Series 7100 Branch Circuit Monitor, Plastic Enclosure, 24 Input, with
LCD Display
70D12-000 Series 7000 Embedded Branch Circuit Monitor, Mounting Plate, 12 Input,
with LCD Display
70N12-000 Series 7000 Embedded Branch Circuit Monitor, Mounting Plate, 12 Input,
with no display
71D12-000 Series 7100 Branch Circuit Monitor, Plastic Enclosure, 12 Input, with LCD Display
70D03 Series 7000 3-Phase Meter, DIN Rail Mount Plastic Enclosure, with LCD Display
71D03 Series 7100 3-Phase Meter, Wall Mount Plastic Enclosure, with LCD Display
Each VerifEye®meter shipment also includes the items below:
• Meter with Options Installed – Serial Number, MAC ID, and FCC ID indicated on
side label
• Pluggable Connectors (voltage, three-position terminals for CT, two-position
terminals for I/O)
• Thumb drive containing VerifEye®Power Meter Viewer Utilities Software, Register
List, Manual, Tutorial Videos
• Certicate of Calibration (COC) for each unit
2 INTRODUCTION
WEB VERSION

7
2.2 Meter Anatomy
All user connections are made on the circuit board. Connectors are
identied by function and include polarity markers.
Cat. 71D12 Series 7100 Branch Circuit Monitor,
Plastic Enclosure 12 Input, with LCD Display
Cat. 70D48 Series 7000 Embedded Branch Circuit Monitor,
Mounting Plate 48 Input, with LCD Display
Conduit
Connection
Alarm
Ethernet
USB
RS-485
+12V Out
Mounting Hole (6)
Voltage Cover
(transparent)
Voltage
Connector
Pulse Input 1 & 2
CT Inputs
Pulse Input 3 & 4
Serial #
Model #
MAC ID(s)
Expansion
Card (12V)
Serial #
Model #
MAC ID(s)
Voltage Cover
(transparent)
Element ID
Plate Ground
Voltage
Input 1
Voltage
Input 2
Element ID
LCD Display
Navigation
Buttons
Expansion
Card (12V)
Alarm
USB
Ethernet
Pulse Input
+12 VDC
RS-485
Pulse Input
2 INTRODUCTION
WEB VERSION

8
White (+)
Black or Brown (-)
Bare (RŌC) (S)
CT Connections (x3)
RS-485
71D03 Series 7100 3-Phase Meter, Wall Mount Plastic Enclosure, with LCD Display
70D03 Series 7000 3-Phase Meter, DIN Rail Mount Plastic Enclosure, with LCD Display
2 INTRODUCTION
WEB VERSION

9
3.1 Project Manager Aspects
Meter installation often includes coordination between individuals or groups of
people with different responsibilities. Spend a few minutes considering who will
be executing each portion of the installation and what tools are needed at each
stage. Things to consider include determining how to communicate with the meter,
setting address conguration, installing Power Meter Viewer Utilities, access to PIN
numbers, etc. The more tasks completed before installation the fewer tasks will
be needed in the eld. The following section gives an overview of typical process
activities followed by details in the next section.
3.1.1 Conguration & Data Viewing Options
The VerifEye®meter has three methods for conguration and data viewing. The
most powerful interface is a Microsoft Windows application (Power Meter Viewer
Utilities ) that runs on PCs or tablets. Power Meter Viewer Utilities is encouraged
for complex installations and is required for conguring advanced functions like
alarms. The second interface is the VerifEye®Web App and is intended for smart
phones or tablets that can connect over USB, or Ethernet. The third interface is
an optional LCD display which is intended for intermittent end-user observation
and is restricted in capability. The RTU can also be used for conguration if
communication settings are already established. The feature set of each interface is
summarized next.
3.1.2 Information Access by Interface Type
* If PINs are congured
Interface
Options
PC or Laptop
Running
Power Meter
Viewer Utilities
Smart Device or
Tablet via
VerifEye Web App
LCD on Meter
(If Equipped)
RTU
(Host System)
Modbus/ACnet
When Meter Setup
Field Visit Field Visit End User Building System
Real Time
Values
All Meter
Parameters
Waveform Capture
Harmonic Analysis
All Element View
Phasor Plot
Alarms
All Meter
Parameters
Multi-Element View
Voltage
Current
VA
VAR
kWh
Single Element
View
All Meter
Parameters
Conguration
Entire Meter
Visual Guides
Copy/Paste
Entire Meter
Text Based
Communications
Only
Entire Meter
Register Based
Security PINs Factory Support –
Level 3
Read Only - Level 1*
Read/Write - Level 2*
Read Only – Level 1*
Read/Write Level 2*
(limited to
communication)
Factory Support
– Level 3
3 PLANNING FOR FIELD INSTALLATION
WEB VERSION

10
3.2 Meter Conguration Overview
Work performed prior to installation saves time, and may result in fewer mistakes.
3.3 Meter Installation Overview
Performed by licensed electrician.
3.4 Verication and Communication Overview
Can be modied when you apply power to the meter.
Tools Typical Work
• Desktop or Laptop PC
• USB Type AB Cable (preferred) or Ethernet and
USB wall charger (> 500 mA)
• Thumb Drive (Power Meter Viewer Utilities
Installer) or access www.Leviton.com, and go
to software downloads for this product.
• Electrical schematics of project
• Install Power Meter Viewer Utilities Software.
• Connect USB/Ethernet cable from PC to meter.
• Establish communication with meter.
• Firmware update (if required)
• Congure software for anticipated meter setup.
• Field wiring documentation
Tools Typical Work
• Mounting hardware (customer supplied)
• Wiring, supplies, labels, and wire ties
• Tablet, Smart Device, or Laptop PC
• Multi Meter, Current Clamp
• Camera
• Mechanical mounting.
• Electrical installation.
• Install voltage cover.
• Apply power to meter.
• Conrm basic operation of meter.
Tools Typical Work
• T
ablet, Smart Device (Web Page Based), or
Laptop PC
(Power Meter Viewer Utilities Software)
• On-site troubleshooting
• Multi Meter, Current Clamp
• Camera
• Locate the power meter.
• Conrm RTU device.
• Add wire terminations (if required).
• Conrm meter communication settings.
• Meter health metrics (check for setup errors).
• Analytics (Power Meter Viewer Utilities).
• Correct instrumentation.
• Set security PINs.
• Checklist
3.5 RTU Programming and Scripting Overview
Tools Typical Work
• Laptop PC (Remote Access to RTU)
• Remote troubleshooting
• Register List
• Conrm meter communication settings.
• Conrm communication protocols.
• Exercise remote connectivity.
• Run conguration scripting.
• Conrm data integrity.
3 PLANNING FOR FIELD INSTALLATION
WEB VERSION

11
This section describes how to set up the VerifEye®meter in an office environment, and
congure the power meter for a pre-determined conguration. The setup is standardized
for an organization or project; however, you can document and e-mail the setup to an
installer. The setup can also be performed on-site, and reect “as-built” congurations.
The Power Meter Viewer Utilities application offers visual guides and context help to
facilitate meter conguration. Please see the Power Meter Viewer Utilities overview
section for additional information. By default, VerifEye®meters are congured for DNS
Ethernet addressing. A common conguration sequence is to use USB to congure
a meter for Ethernet communications at a static IP address, then switch from USB to
Ethernet to locate it. To facilitate this, select [Refresh Connectivity] on the Power Meter
Viewer Utilities software screen.
4.1 Install the Power Meter Viewer Utilities Software
Insert the Power Meter Viewer Utilities thumb drive into the computer or download
it from the Leviton FTP site (qualied Leviton personnel only). The installer starts
automatically. If it does not, browse the thumb drive and locate the Setup.exe
program, double-click it, and follow the installer instructions.
For Custom Installation
For users who want to specify the location of the Power Meter Viewer Utilities
software and support les, double-click the [supportles] folder, and run setup.
exe. This prompts the user for additional details.
4.1.1 Connection and Conguration Options Using Power Meter Viewer Utilities
When you launch the Power Meter Viewer Utilities application, it prompts the
user to select one of four connectivity options.
• Connect over USB cable.
• Connect over Ethernet to a Predetermined IP address.
• Scan Network.
• Create Setup le only (no meter connected).
NOTE: The USB connection method is
recommended for new users who have physical
access to the meter using a USB A to B cable.
4 METER CONFIGURATION
WEB VERSION

12
4.1.2 USB Connection (Power and Communications)
1. Connect the VerifEye®meter to a USB port on your computer to provide
both power and communications.
a. If equipped, the LCD display is the most visible indication of a
running meter.
b. For meters without a display, a green ashing LED on the circuit board
indicates that the VerifEye®meter booted up and is running.
CAUTION: The VerifEye®meter draws 450 mA from the USB port. Be sure
the USB host is industry standard; otherwise, overloading may occur. If the
meter fails to power or ickers when powering over USB, you must use an
alternate conguration for power.
2. Launch the Power Meter Viewer Utilities application and select
[CONNECT OVER USB] in the pop-up window.
The meter starts to communicate.
4.1.3 Ethernet Network Connections
To congure the meter over Ethernet requires a secondary power connection.
The meter does not support Power Over Ethernet (POE). If the meter is
already installed within the buildings electrical network, closing the AC
breaker (or approved disconnect) turns ON the meter through the meter’s
internal power supply.
NOTES:
• If a computer’s USB port cannot provide 500 mA of current, you can use an
AC/USB charger or a USB battery as a power source for
Ethernet communications.
• Both the Network Scan and Connect Over Ethernet to IP options require
that a valid network connection exists between the VerifEye® meter and
conguration PC.
4.1.4 Dynamic Host Conguration Protocol (DHCP):
VerifEye®meters ship in the DHCP mode to prevent IP conicts with other
equipment. The meter expects to receive an IP address from a DHCP service
provided by a router, Layer 3 switch, or a server providing DHCP service.
Therefore, if the VerifEye®meter and the host PC request an IP address from
the same DHCP service provider, they can communicate. When the VerifEye®
meter powers up, the IP address is shown on the LCD display (if equipped),
or can be found using the Network Scan function.
4 METER CONFIGURATION
WEB VERSION

13
4.1.5 Direct Connection
When a PC is directly connected to a VerifEye®meter via an Ethernet cable,
no DHCP service exists. This conguration can be made to work, but requires
changes to either the meter communication settings or the PC network
conguration.
LCD Display
For units equipped with an LCD display, navigate to Communications >
Ethernet Settings > DHCP > OFF.
Change the IP address in the meter to match the subnet of your PC’s IP
address, which makes the meter's IP address unique.You can also note the
current address on the meter and prepare to congure your PC’s IP settings
as shown below.
Go to PC's Control Panel
> Network and Sharing Center
> Change Adapter Settings
> Properties
> Internet Protocol Version 4 (TCP/IPv4)
> Properties
Change Computer IP Address and Subnet Mask to 192.168.1.100 and
255.255.255.000 respectively.
Once the PC and VerifEye®meter are set to communicate on the same IP
subnet:
1. Launch the Power Meter Viewer Utilities application and enter the IP
address of the meter (shown as the factory default).
2. Select [Connect over Ethernet to:] in the pop-up window.
The meter starts to communicate.
For more information on conguring the meter, see the Power Meter Viewer
Utilities overview section.
No LCD Display
If the IP address of the meter is set to static, a VerifEye®meter without a
display can only communicate directly with a PC over Ethernet. You must set
the IP address prior to using another interface, such as USB or serial.
4 METER CONFIGURATION
WEB VERSION

14
4.1.6 Network Scan
Network Scan is a feature for monitoring previously installed and congured
VerifEye®meters over an Ethernet network. Network Scan broadcasts a UDP
discovery packet on the same network as the PC that runs the Power Meter
Viewer Utilities application. Normally, this is performed on a corporate network
running DHCP. Any VerifEye®meter that responds is displayed in a table
that includes the system description register, IP address, serial number, and
communication conguration.
Highlight the desired meter, and select OK, Test or Setup. Note that the
effectiveness of this technique is highly dependent on the conguration of
the PC running Power Meter Viewer Utilities (which may have more than one
network card) and the network conguration. Select Rescan to make multiple
attempts to locate a particular meter on busy networks (UDP has no built-in
retry provisions).
4.1.7 Launch Congurator
The nal option in the Power Meter Viewer Utilities Connect to Meter
pop-up window is Launch Congurator. This option allows you to create
a meter setup or alarm table for future use without connecting to a meter.
After prompting the user for a meter model, the Power Meter Viewer Utilities
application launches under a mode with restricted functionality. This mode
operates on les only.
4 METER CONFIGURATION
WEB VERSION

15
4.2 Power Meter Viewer Utilities Software Overview
Power Meter Viewer Utilities is a Windows application, and is used to congure
and verify a VerifEye®meter. All functions and menus are accessed under the
central drop-down list, which has a content lter for viewing Basic metering data
or Extended meter data that can be helpful in troubleshooting. The information
displayed in the drop-down list for each lter setting is summarized below.
ExtendedBasic
Display Data Basic Extended
Monitor
Power a a
Energy a a
Demand a a
Power Factor a
Waveform Capture a
Harmonics a
Phasor Plots a
Meter
Setup
Communication
Setup aa
Alarms a
Advanced a a
About the Meter a a
4 METER CONFIGURATION
WEB VERSION

16
4.2.1 Conguring Electrical Components Using Power Meter Viewer Utilities
1. Navigate to Meter Setup under the Display Menu List Box.
2. Enter a System Description for the physical location of the meter.
3. Enter Element Description (defaults are A, B, etc.).
4. Select the Voltage Input (voltage connector 1 or 2) - for OS48 only.
5. Select the Voltage Multiplier (optional).
6. Select the Service Type (3-Phase 4-Wire, etc.).
7. Select CT Type (HSC-050, etc.).
8. Set CT Multiplier (optional).
9. Set CT Flipper (optional).
10. Repeat steps 3 - 7 for each Element.
11. Click SEND SETUP TO METER.
4 METER CONFIGURATION
WEB VERSION

17
4.2.2 Conguring RS-485 Communications Using Power Meter Viewer Utilities
If planning to setup communication via RS-485, follow the steps below:
1. Navigate to Communication Setup under Display Menu List Box.
2. Select RS-485.
3. Select either Modbus or BACnet.
If you selected Modbus, set the following:
• Serial Settings
• Set Modbus Address
If you selected BACnet, set the following:
• Serial Settings
• Device ID
• MS/TP Address
• Max Masters (optional)
• Max Info Frames (optional)
4. Click SEND SETUP TO METER.
4 METER CONFIGURATION
WEB VERSION

18
4.2.3 Conguring Ethernet Communications Using Power Meter Viewer Utilities
If planning to setup communication via Ethernet, follow the steps below.
1. Navigate to Communication Setup under the Display Menu List Box.
2. Select Ethernet.
3. Select either Modbus or BACnet.
4. If you selected Modbus, set the following:
Modbus Port (optional)
If you selected BACnet, set the following:
• Device ID
• BACnet Port and BBMD
5. Select either DHCP or Static IP.
6. If you selected DHCP, proceed to the next step.
If you selected Static IP, set the following:
• Static IP Address
• Subnet Mask
• Gateway Mask
• Default Gateway
7. Click SEND SETUP TO METER.
4 METER CONFIGURATION
WEB VERSION

19
4.2.4 Conguring Alarms in Power Meter Viewer Utilities
The VerifEye®power meter has the ability to set alarms for over and under
conditions for voltage and current on any meter channel.
Conguration Input Methods
Power Meter Viewer Utilities uses dynamic entry for the specication of Alarm
settings. Whichever text entry eld is selected becomes the forcing condition
and the other related elds are updated by calculation to reect a consistent
set of conditions. The text entry elds in grey are Conguration and are NOT
retained by the meter. Only the elds with a black background are stored in
the meter's memory or in conguration les.
Nominal Values
Entering alarm thresholds based on “percent of nominal” values is helpful
when alarm conditions are centered around electrical components or industry
standard conditions. For example, an over current alarm may be set to 80%
of an installed circuit breaker to alert when that breaker exceeds
NEC recommendations.
Absolute Values
Entering alarms based on absolute value enables you to enter the triggering
values directly in the register elds (black background).
4 METER CONFIGURATION
WEB VERSION

20
4.2.5 Setting the Real Time Clock
The VerifEye®meter includes a Real Time Clock. The clock is used only to
time stamp Interval Data in the log. It is not used for calculation within the
meter. For those customers using the IDR function of the meter, it is helpful
(but not necessary) to set the real time clock so that data records can be
uniquely identied. The time can be set using Power Meter Viewer Utilities,
under the Advanced Tab, by clicking on the small time icon in the bottom-right
corner of the clock.
The clock icon launches the Window Calendar and allows the user to choose
the desired date and time. Click Set Time to Now to populate the current time.
Click OK to commit this time to the RTC chip onboard the meter.
Real Time Clock Power Source
The RTC integrated circuit is a stand-alone low power circuit within the
VerifEye®meter. Time is kept in the absence of a connected external power
source (AC or USB power) by a super capacitor. The capacitor can keep the
RTC running over normal power outages (days to weeks), but it does not keep
time while the meter is stored or shipped.
NOTE: It is recommended that users use the Interval Data Recording
capability of the VerifEye®meter to ensure the Real Time Clock is set as part
of the commissioning process.
4 METER CONFIGURATION
WEB VERSION