Leviton Verifeye 8000 Series User manual

VerifEye™
Series 8000 Meter
User Guide
WEB VERSION

WEB VERSION

1
TABLE OF CONTENTS
Warnings and Cautions
1. Introduction
Section 1.1 Meter Features System Description
Section 1.2 Series 8000 System Specifications
Table 1: Series 8000 Meter System Specifications
Front Panel Display
Figure 1: Series 8000 Front Panel
Figure 2: Series 8000 Internal View
Figure 3: Product Dimensions
Figure 4: Product Wiring Diagram
2. Safety Precautions
Section 2.1 Electrical Safety Compliance
3. Installation
Section 3.1 Pre-Installation
3.1.1 Pre-Installation Checklist
3.1.2 Site Planning
3.1.3 Installation Procedures
3.1.4 Mounting the Series 8000
Figure 5: 120V Mounting Layout, Dimensions and Clearances
3.1.5 Installing Potential Transformers for 3PH Service greater than 277V
Figure 6: Potential Transformer Chassis
Figure 7: Typical 3PH 347V Installation
3.1.6 Installing the Sense Voltage and Control Voltage Cables in Wye and Delta Services
Figure 8: 120/240V Single-Phase Connection
Figure 9: 120/240V Three-Phase Wye panel with 120V variant
Figure 10: 120/208V Three-Phase Wye panel version with a Wiring Harness
Figure 11: 277/480V Three-Phase panel with 120V variant
Figure 12: 277/480V Three-Phase panel with 277V variant
Figure 13: 347/600V or higher 3PH Wye panel with PTs with the 120V variant
Figure 14: 3PH Delta panel with 120V variant
4. Installing Current Transformers
5. Connecting the Ethernet Communications
6. Connecting the Modbus RTU Communications
Figure 15: Modbus Wiring Diagram
7. Start-Up Sequence
Section 7.1 Manually Testing Communications
8. Pulse Inputs
9. Display Navigation
Section 9.1 Normal Mode
Section 9.2 Diagnostic Mode
10. Configuration Tool Installation
Section 10.1 Network and Meter Setup
Section 10.2 Connecting to S8000 Meter
11. Regulatory Compliance
12. Warranty
2
3
3
3
4
5
5
6
7
8
9
9
10
10
11
11
11
11
12
13
13
14
15, 16
17
18
19
20
21
22
23
24, 25
26
27
27
28
28
29
30
30
30
31
31
32, 33
34
35
WEB VERSION

2
• Please refer to the product manual or call/E-mail the Leviton®Meter Support Team for further
assistance (800-959-6004 / [email protected]).
• For the full listing of tools and equipment required for the complete installation of this
product, please refer to the manual for details.
• 347/600 V and 480 V Delta services require external PTs to step down the voltages before
being wired to the meter.
IMPORTANT NOTES
HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH
• TO AVOID DEATH, PERSONAL INJURY OR PROPERTY DAMAGE, disconnect service
voltage from the panel and use caution when working around energized circuits.
• Ensure the installation is completed per NEC®guidelines as well as local codes.
• A disconnect must be provided (such as a breaker from the panel) that will allow shut off of
power to the meter for servicing.
• Voltage references to the meter should be connected to a circuit breaker in the panel and/or
with appropriate fusing based on the NEC®and any local codes that are applicable.
• Apply appropriate personal protective equipment (PPF) and follow safe electrical work
practices. See NFPA 70E.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors and covers before turning on power to this equipment.
• The meters must be connected to the sense voltage and control voltage through a properly
rated voltage disconnect (not shown in the wiring diagrams).
Failure to follow these instructions will result in death or serious injury.
WARNINGS AND CAUTIONS
WEB VERSION

3
INTRODUCTION
1. INTRODUCTION
This document describes the Series 8000; including procedures to install and start up the unit, and
complete the initial configuration:
• "System Description"
• "Pre-Installation"
• "Installation Procedures"
• "Start-Up Sequence"
• "Fuse Replacement"
This documentation is intended for those responsible for installing and configuring the Series 8000
meters. Installers must be qualified electricians with knowledge of local and national code requirements.
See "Safety Precautions".
1.1 Meter Features System Description
The Series 8000 meters support:
• Single-Phase, 2-wire
• Single-Phase, 3-wire (network)
• Three-Phase Wye and Delta services
Depending on how the meters are installed and configured, they can meter 8, 12, or 24 individual meter
points. The Series 8000 meters are designed for residential, commercial, and industrial use and display
the power and consumption readings for each measurement point.
1.2 Series 8000 System Specifications
The Series 8000 system architecture includes:
• Single-Phase, 2-wire; Single-Phase, 3-wire (network); and Three-Phase compatibility
• 120/208V, 120/240V and 277/480V configurations, and 347/600V with external potential
transformers
• Up to 8, 12, or 24 individual meter points
• Local Ethernet configuration interface via PC and web browser
• Ethernet ports for remote reporting
• Modbus serial port for remote reporting
• Serial port for remote display
• 2 pulse inputs to connect metering devices
WEB VERSION

4
Specification Series 8000
Model: S8UTS/277TS
Series 8000
Model: S8UWH/277WH
Dimensions Height: 13.125 in. (33.5 cm)
Width: 12 in. (30.5 cm)
Depth: 2.125 in. (5.5 cm)
Height: 13.125 in. (33.5 cm)
Width: 12 in. (30.5 cm)
Depth: 2.125 in. (5.5 cm)
Weight 8.77 lb (3.98 kg) 8.77 lb (3.98 kg)
Sense Voltage 100V to 300V 60Hz
2W+N+Protective Earth Wye 3W+N+Protective
Earth Wye 3W+Protective Earth Delta
100V to 300V 60Hz
2W+N+Protective earth 3W+N+Protective
Earth Wye 3W+Protective Earth Delta
Control voltage and current North America: 120V 125 mA 60 Hz North America: 120V 125 mA 60 Hz
Current Transformers
Measurement Category III
100mA
Note: All CTs used with the product must be UL
recognized/listed.
For CT Part Numbers (see S8000 Data Sheet)
100mA
Note: All CTs used with the product must be UL
recognized/listed.
For CT Part Numbers (see S8000 Data Sheet)
Measurement Accuracy
(accuracy compliant when used
with 0.3% CTs)
ANSI C12.20 Class 0.5
IEC 62053-22 Class 0.5S
ANSI C12.20 Class 0.5
IEC 62053-22 Class 0.5S
Measurement Canada Approved EG07 compliant
Pulse inputs 1 and 2 Dry form A and solid-state form A compatible
Maximum frequency 10 Hz
Minimum pulse width 20 ms
Dry form A and solid-state form A compatible
Maximum frequency 10 Hz
Minimum pulse width 20 ms
Non-volatile memory storage 120 days in 15 minute intervals 120 days in 15 minute intervals
On-board Ethernet port 10/100 Mb/s 10/100 Mb/s
On-board Modbus serial port RS422 or RS485 19200/9600 Baud RS422 or RS485 19200/9600 Baud
Serial port 115 kb/s 115 kb/s
Fuse rating (F1) North America: 120V: T125 mA, 250V North America: 120V: T125 mA, 250V
Environmental
Operating Temperature -40 to 70°C -40 to 70°C
Operating humidity 5% to 90% non-condensing 5% to 90% non-condensing
Usage environment Indoor or enclosed outdoor environment Indoor or enclosed outdoor environment
Maximum altitude 9843 ft (3000 m) 9843 ft (3000 m)
Pollution degree 2 2
INTRODUCTION
Table 1: Series 8000 Meter System Specifications
WEB VERSION

5
INTRODUCTION
Front Panel Display
The Series 8000 meters have the following front panel features (Figure 1):
• LCD - displays 2 rows of 16 characters for each of the meter points (8, 12, or 24)
• Display button - cycles through the available information for each of the meter points
• Left and right arrow buttons - selects which of the meter points is on the display
Figure 1: Series 8000 Front Panel
WEB VERSION

6
INTRODUCTION
Figure 2 shows the internal view of the Series 8000
Figure 2: Series 8000 Internal View (Meter Only)
Earth Stud
Ingress
Punch-outs
Cover Screw
Location
Mounting
Keyhole
Meter Point
Input Connector
Cover Screw
Location
Sense Voltage
Terminal Block
Control Voltage
Terminal Block Fuse
Control Voltage
Jumper
Cover Screw
Location
Modbus RTU Port
Display
Remote Display
Serial RS232
Ethernet Port
Pulse In
Terminal Blocks
Pulse Out
Connector
Cover Screw
Location
WEB VERSION

7
INTRODUCTION
13.53”
(343.7mm)
12.58”
(319.5mm)
480V DELTA
ENCLOSURE
SHORTING
OR
TERMINATION
ENCLOSURE
S8000
3.50” (88.9mm) MIN
2.25”
(57.2mm)
12.58”
(319.5mm)
8.39”
(213.1mm)
13.19”
(335.0mm)
6.50”
(165.1mm)
Figure 3 shows the dimensions of the Potential Transformer, Series 8000 Meter and CT Termination
enclosure.
Figure 3: Product Dimensions
WEB VERSION

8
INTRODUCTION
Figure 4 shows the a functional diagram of how all possible components fit together for a 3 Phase
3 wire installation.
Figure 4: Product Wiring Diagram
PT Enclosure
(OPTIONAL)*
Series
8000
CT Termination
Enclosure
WEB VERSION