Leviton A8810-41M User manual

DI-000-A8810-00A
Energy Management Hub and 3-Phase Meter
EMX Data Acquisition System
Cat. No. A8810-41M/41R
Installation Guide

TABLE OF CONTENTS
Warnings ..............................................................................................................................................1
Cautions ...............................................................................................................................................1
1 Getting Started ..................................................................................................................................2
2 Site Location and Providing Power ...............................................................................................4
3 Internal Component Configuration and Operation .......................................................................7
4 Final Steps .....................................................................................................................................11
5 Standard Statements .....................................................................................................................15

WARNINGS:
• TO AVOID FIRE, SHOCK OR DEATH, turn off all power supplying equipment before working on or
inside the equipment. Use a properly rated voltage sensing device to confirm power is off.
• RISK OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. CAREFULLY READ AND FOLLOW
INSTRUCTIONS:
• This equipment MUST be installed and serviced by qualified electrical personnel with the requisite
knowledge, training and experience related to the installation and operation of this equipment.
• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.
• Product may use multiple voltage/power sources. Be sure all sources of power have been disconnected
before servicing.
• Do not depend on this product for voltage indication.
• Only install this product on insulated conductors.
CAUTIONS:
• This product is not intended for life or safety applications.
• Do not install this product in hazardous or classified locations.
• The installer is responsible for conformance to all applicable codes.
• Mount this product inside a suitable fire and electrical enclosure.
• If the collector is connected directly to a source of voltage, the pulse isolator will immediately burn out
and become non-responsive.
WARNINGS AND CAUTIONS
1

2
1 GETTING STARTED
1.1 Recommended Installation Hardware
Not all installations will be the same, but in general we recommend that you have the
following available:
• Power Drill
• Large Phillips Head – Number 2
• Small Flathead 2.5mm or 1/8”
• Laptop – Windows PC with Ethernet Port
• Cable Glands and Weatherproof Sealant
• Digital Multimeter
• CAT 5 Cable
• Belden™1120A Twisted Shielded Pair wire
• Wire Strippers
• Mounting Screws (4)
1.2 Packing List
The following Items are included with the panel:
• Enclosure Mounting Tabs
• Short Ethernet Patch Cable
• Ethernet Cable 7’
• Calibration Certificates, Operating Manuals, Engineering Drawings, and Wiring
Diagrams are located on the inside of the enclosure door.
• This enclosure is packed for protection during transit. Please inspect all materials
upon receipt to ensure no damage has occurred in transit. Please report any
damage to your product to your vendor immediately. Packing material must
be removed for operation. Please discard, recycle, or reuse these materials
appropriately.
Technical Support
For technical support, contact Leviton at 800-959-6004, or via email at
[email protected]

1 GETTING STARTED
3
1.3 Product Overview
The EMX panel comes fully assembled, wired and ready for installation.
Neutral and Ground
input terminals
Power Meter –
Series 4100
Bi-Directional
(4DUMR split core
or Rogowski coil
versions)
Energy Monitoring
Hub - A8810
Power Supply
– Phoenix
Contact Step-PS
277AC/24DC/3.5A
Separate 3-Phase
(meter reference
voltage) and Single-
Phase (system
power) fused AC
power input terminals
Current Transformer
input terminals

2 SITE LOCATION AND PROVIDING POWER
2.1 Mounting the Enclosure
2.1.1 Mount the enclosure in a location according to and compliant with local
electric code.
2.1.2 Mounting Tabs and screws are provided with the enclosure. The provided
screws are intended to be used to mount the tabs to the enclosure. User to
provide additional mounting hardware as needed.
2.1.3 Create knockout holes for any necessary power, current transformer and
communications lines in the bottom of the enclosure.
2.1.3.1 To maintain the warranty and integrity of the panel, all holes/punch
outs for conduit and wires should only be drilled in the bottom of the
enclosure and properly sealed to prevent exposure to moisture.
2.1.3.2 To prevent interference, it is recommended that sense voltage and CT
wiring are separated and run through different knock outs.
2.1.4 The enclosure does have the ability to be padlocked externally. This is
recommended to maintain security and device integrity.
4

5
2 SITE LOCATION AND PROVIDING POWER
2.2 Connecting Input Power
2.2.1 Per local electrical code and site specifications connect power to voltage
sense input and panel power input.
2.2.2 There are separate power inputs for meter reference voltage and panel power
to allow the hub and meter to remain powered if the circuits being monitored
need to be off.
2.3 Connecting Current Transformers
2.3.1 CT inputs are located next to the power input section on the lower DIN rail.
2.3.2 CT should be wired per manufacturer directions indicated below. CT terminals
are clearly labeled CT1 (X1/X2), CT2 (X1/X2), and CT3 (X1/X2).

6
2 SITE LOCATION AND PROVIDING POWER
2.4 Observe correct CT orientation
N
X1 White
A
B
C
N
X1
X2 A
X1
X2 B
X1
X2 C
Black
X2
L1
L1
X1 White
A
B
C
N
X1
X2 A
X1
X2 B
X1
X2 C
Black
X2
L2
L1N
X1 White
A
B
C
N
X1
X2 A
X1
X2 B
X1
X2 C
Black
White
Black
X2 X1
X2
L2
L2L1
X1 White
A
B
C
N
X1
X2 A
X1
X2 B
X1
X2 C
Black
White
Black
X2 X1
X2 White
Black
X1
X2
L3
L2L1N
X1 White
A
B
C
N
X1
X2 A
X1
X2 B
X1
X2 C
Black
White
Black
X2 X1
X2 White
Black
X1
X2
L3
L2L1N
X1 White
A
B
C
N
X1
X2 A
X1
X2 B
X1
X2 C
Black
White
Black
X2 X1
X2 White
Black
X1
X2
L3
Diagram 1: 1-Phase Line-to-Neutral
2-Wire System 1CT
Diagram 2: 1-Phase Line-to-Line
2-Wire System 1CT
Diagram 3: 1-Phase Direct Voltage
Connection 2CT
Diagram 4: 3-Phase 3-Wire 3 CT no PT
Diagram 5: 3-Phase 4-Wire Wye Direct
Voltage Input Connection 3 CT
Diagram 6: 3-Phase 4-Wire Wye
Connection 3CT 3 PT
Use System Type 10 (1L + 1n) Use System Type 11 (2L)
Use System Type 12 (2L + 1n) Use System Type 31 (3L)
Use System Type 40 (3L + 1n) Use System Type 40 (3L + 1n)

7
3 INTERNAL COMPONENT CONFIGURATION AND OPERATION
3.1 Introduction
The Leviton EMX comes with multiple internal components that are essential to operation.
The following describes these components and outlines basic installation instructions.
3.2 Phoenix Contact Power Supply
Description: The Phoenix Power Supply provides DC power to the components within
the cabinet, and, if needed, external devices that you may wish to power. There are no
installation steps required, however the following are some product details.
3.2.1 Model Number: STEP-PS/277AC/24DC/3.5 - 2904945
3.2.2 Nominal Input Voltage Range: 100 VAC – 277 VAC
3.2.3 Nominal Output Voltage: 24 VDC
3.2.4 Nominal Output Current: 3.5A
3.3 Leviton 4DUMR Power Meter
Description: The Leviton 4DUMR is a revenue grade, bi-directional, power meter that
provides information about the electrical performance of the monitored circuit.
Configuration of the meter assumes that the meter has arrived with factory default
settings. In the steps below you will: Set up communication parameters, voltage and
current information, and system information. All of this can be done with the push buttons
on the meter.
Important: Note now whether you have Split Core or Rogowski “Rope” CT as it will
alter the steps that follow.