Leviton WSS10 User manual

Dip Switch Settings:
NOTE: To access dip switch settings, lift up the bottom of the switch pad.
Single Pole Wiring Application:
• WSS10ReceiverControlSwitchisonly
intendedasaSinglePoledevice.
Multiple Location Wiring Application:
• WSS0SWirelessRemoteSwitchcanbeusedforadditional
switches(3-wayand4-way),nowiresnecessary .
SinglePole(OneLocation)
Wireless Signal Receiver Switch
Cat.No.WSS10
Incandescent:800W@120V–Ballast:1200VA@120V,2700VA@277V
120-277VAC,50/60Hz,Motor:1/4HP@120V
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.
• Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician.
• WSS10-GDxproductsdonotrequireaneutralwire,thereisaminimumloadrequirementof25wattsfortheseproducts.
Tools needed
Description
Slotted/PhillipsScrewdriver ElectricalTape Pliers Pencil
Cutters Ruler WireNuts
Push in side at
tab to release
Line up tabs
and press in
side to attach
ColorchangeoptionsareavailablefromLeviton,consultyoulocalLeviton
Distributor.Tochangecolorofframe,proceedasfollows:
Changing the color of your Switch
Installation
NOTE:UsecheckboxeswhenStepsarecompleted.
√
Step 3
Step 4
Step 2 Identifying your wiring application
(most common):
NOTE:Ifthewiringinyour
wallboxdoesnotresemble
thisconguration,consultan
electrician.
2
4
3
1
WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN
OFF POWERatcircuitbreakerorfuseandtestthatpoweris
offbeforewiring!
Step 1
WIRING SWITCH:
Connect wires per WIRING DIAGRAM
below as follows:
• Connect(Hot)wirefromwallboxto
blackwireonswitch.
• Connect(Load)wireinwallboxto
bluewireonswitch.
• Connect(Neutral)wireinwallboxto
whitewireonswitch.
NOTE:ForNoNeutralmodel,white
wirewillnotbeavailable(Figure 2).
BK WH
2
Black wire (BK)
Blue wire (BL)
White wire (WH)
1
3
4
BK
BL
Switch
Black
White
Load
Neutral (White)
Line
120-277VAC,
50/60 Hz
Hot (Black)
BKWH
BL
Switch
Black
White
Load
Neutral (White)
Line
120-277VAC,
50/60 Hz
Hot (Black)
Auto-On / Auto-Off mode:Automodecanbeenabledusingthedipswitches,product
comesfromthefactoryinManual-On/Auto-Off.
Walk-through:canbeusedonlyinAuto-Onmodeandisrecommendedonlywhen
usingbatteriesorlowvoltagepowerconnection.
Timeout:2(test),10,20,30min;(Longertimedelayisrecommendedforcontinuous
selfpoweringofthesensorandtoensurepacketsaresenttothereceiverswitch).
Dip switches 1-4
OPEN
ON
1 2 3 4
Cat.No.WSS10isthereceiverswitch.Thisswitchhasasingleswitchpadthat
togglestherelayanditscorrespondingload,ONandOFF.IftherelayisOFF,the
relaywillturnONwhenthepush-buttonispressed,andvice-versa.TheIndicator
LEDwillblinkRedwhenaag/packetisreceivedfromthesensororremoteswitch.
NOTE:theno-neutralversionhasaminimumloadrequirementof25watts.
Cat.No.WSCxxisthesensor(s).TheSensorUnitsendsaag/packetwiththe
presenceofmotiontothereceiverswitchwhichthenkeepstheloadON.Inthe
absenceofmotion,theSensorUnitwillstopsendingag/packetstothereceiver
switch;whenthereceiverswitchnolongerreceivesapacket,theTimeOutwill
start,thentime-outandturntherelayOFF.TimeDelaystartsasofthelastmotion
detectedinthespace.TheMotionIndicatorLEDwillblinkRed(1blinkperminute)
everytimemotionisdetected,sendingaag/packettothereceiver.TheLEDon
theWSS10receiverwillblinkRed,acknowledgingthereceptionofaag/packet.
• WSCxx & WSS10 (together):InManual-On/Auto-Offmode,thebuttonmust
bepressedtoturnthelightsON.Intheabsenceofags/packetssentfromthe
sensor,thereceiverswitchwillTime-OutandturnthelightsOFF.
• WSCxx & WSS10 (together):InAuto-On/Auto-Offmode,thesensorwillsenda
ag/packettothereceivertoturnthelightsON.Intheabsenceofags/packets
sentfromthesensor,thereceiverswitchwillTime-OutandturnthelightsOFF.
NOTE:Thesensormustsensemotionandsendapackettostartthetimedelay
andenableAuto-Off.
• WSCxx & WSS10 (together):Allowthe30secondvacancyconrmation
featurewhichexiststoturntherelaybackONincaseoffalseOFF.
Self Powered Products:Thesensorandremoteswitchareselfpowereddevices
usingEnOceantechnology.
• TheSensorutilizesasolarpanelwhichpowersthesensorfromtherooms
ambientlight.Thesensorwillstarttofunctionwithinaminuteofexposureto
light.Thetotalchargetimeforthesensorwillvarydependingonintensityof
lightandlengthofexposuretolight.Theminimumlightrequirementforthe
sensoris40LUX(4FC).
• Theremoteswitchutilizeskineticenergyfromthemechanicalswitchwhen
pushingthepad.Thisfrictionthenstoresenoughenergytotransmitanother
signalonthenextpressactionofthepad,testedover50,000cycles.
Battery option:Theuseof(3)AAAbatteries(notincluded)isnotrequiredbutcan
beusedinareaswherenolightisexpectedforlongperiodsoftime.
Low Voltage option:The5-24VDCconnection,isprovidedandrecommended
whenusedinareaswherenolightisexpectedforlongperiodsoftime.
Factory settings:
WSS10:ManualOn/AutoOff,Walkthru=disabled,Timedelay=10min.
WSCxx:Range(PIRsensitivity)=75%
Factory setting operation:
Whenenteringtheroom,thewirelessreceivercontrolswitchwillneedtobemanually
turnedON.Oncelearnedintothereceiverswitch,theWirelessoccupancysensorwill
sendag/packetstothereceiverswitch,keepingthelightsonuntiltheroomisvacant.
Oncethesensorstopssendingag/packets,thereceivertimeoutwillstart,thenturn
thelightsOFFaftertimeoutperiod.
WARNINGS AND CAUTIONS:
•Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingtheWSS10.
•Usethisdevicewithcopper or copper clad wire only.
•Recommendedminimumwallboxdepthis2-1/2”. PK-93664-10-00-0C
Programming Instructions:
Step 5
DIP SWITCH SETTINGS
3
3
4
1
2
4
3
4
3
4
Dip Switch
10 Min Time-Out
30 Min Time-Out
20 Min Time-Out
2 Min Time-Out
-
-
X
ON Position
ON Position
-
ON Position
ON Position
X
-
ON Position
X
X
Manual-On/Auto-Off
Walk Through On
X
X
-
OFF Position
OFF Position
OFF Position
X
OFF Position
OFF Position
-
X
-
-
Auto-ON/Auto-Off
Walk Through Off
Time-Outs:
TheSensorhasfourtime-outsettings:2(test),10,20,or30min.(longertimeout
isrecommendedforselfpoweringindarkspaces).Thevaluesoftime-outisuser
selectedthroughtheuseoftheDipSwitchSettings.NOTE:Sincethesensoris
onlysendingapacketeveryminute,the2minutetimedelayisnotsufcientfor
normaloperation.
Walk-Through Time Delay:
Thewalk-throughfeatureisonlyactiveintheAuto-On/Auto-Offmodewithtime
delayof10,20or30min,isusefulwhenaroomismomentarilyoccupied.Withthis
feature,theSensorwillturnthelightsOFFshortlyafterthepersonleavestheroom.
Thewalk-throughfeatureworksinthefollowingmanner:Whenapersonentersthe
room,thelightswillturnON.Ifthepersonleavestheroombeforethewalk-through
time-outof2.5minutes,theSensorwillturnthelightsOFFwithin2.5minutesof
nooccupancydetected.Iftheroomisoccupiedforlongerthan2.5minutes,the
SensorwillentertheOccupiedModewiththetime-outdurationspeciedbythe
DipSwitchsetting.
1. ReadalltheProgrammingstepsbeforetakinganyactiontoprogramthe
receiver.
2. EnterProgrammingModebypressingandholdingtheswitchbuttonfor15
Seconds,TheLEDontheswitchwillbeginashingAmberslowly1xper
second.ThisistheModeSelectionareaofprogramming.Releasethebutton.
3. ProceedtoreadingRocker Mode, Momentary Mode,Toggle Mode and then
Scene Mode instructions.
NOTE: Amber flashing LED represents the Mode Selection Area of programming,
no buttons can be learned into a receiver with Amber flashing lights.
Rocker Mode Programming Instructions
(LED flashing Amber 1x per second)
1. ReadallRockerModeprogrammingstepsbeforetakinganyactiontoprogram
receiverinRockerMode.
2. Upon entering programming, the device will automatically begin in
Rocker Mode (Amber flash 1x per sec).
3. ToLearnatransmitterswitchinRockerModepressandholdthebuttonfor5
seconds.TheLEDwillchangefromAmbertoGreen*orRed**tosignifyyou
arenowintheLearnareaofprogramming.Releasethebutton.
4. WhenlearningawirelessDecora®stylelightswitchtothereceiver,press
oneendofaswitchrocker.Whenlearningatransmitterotherthanawireless
lightswitch,presstheLEARNbuttononthetransmitter(see appropriate
transmitter instruction sheet).TheLEDwillchange/increaseGreen*
ashingandtheloadwillstayONforabout3secondsindicatingthatthe
receiverhasstoredthetransmitter’suniqueIDinitsmemory.
NOTE: Pressing the transmitter switch again will unlearn the unique ID. (refer
to below: Clear One Transmitter from Programming Mode).
NOTE: (If only one transmitter is desired then skip Step 5 and exit Learn
Mode by following Step 7).
5. ToprogramadditionaltransmitterstocommunicatewiththisreceiverinRocker
Mode,waituntilLEDashingresumes.RepeattheinstructionsinStep 4
untiltheuniqueIDsofalldesiredtransmittersarestoredintheRockerMode
memoryofthereceiver(upto10).
6. To program a additional transmitters to communicate with this receiver
in another Mode, press the receiver button and return to Mode Selection
area (Amber LED flashing).TheAmberLEDwillbeashing1xpersecond
forRockerMode.PressingthereceiverswitchbuttonwilladvancetheAmber
ashingtothenextProgrammingMode,MomentaryMode(Amberash2xper
second).FollowSteps 3 and 4toprogramtransmitterstoMomentaryMode.
7. ToexitLearnMode,justwait;thereceiverautomaticallyexitsLearnModeafter
30seconds(indicatedbytheceasingoftheLEDashing).
Single Pole
1. Line
2. Neutral
3. Ground
4. Load
Figure 1 - WithNeutral
 (whitewire)
Figure 2 - NoNeutral
(nowhitewire)

FCC COMPLIANCE STATEMENT
Thisdevicecomplieswithpart15oftheFCCrules.Operationissubject
tothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,
includinginterferencethatmaycauseundesiredoperation.Anychanges
ormodicationsnotexpresslyapprovedbyLevitoncouldvoidtheuser’s
authoritytooperatethisequipment.
Restore Power:
Restorepoweratcircuitbreakerorfuse.
Installation is complete.
©2010LevitonMfgCo.,Inc. PK-93664-10-00-0C
CoveredbyoneormoreUS&ForeignPatentsandpatentspending
AllRightsIncludingTradeDressRightsReserved
For additional information, contact Leviton’s Techline at
1-800-959-6004 or visit Leviton’s website at www.leviton.com
Push pad
Locator LED
LIMITED 5YEAR WARRANTY AND EXCLUSIONS
Levitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetof anyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’s onlyobligationisto correctsuchdefectsbyrepairor replacement,
at its option, if within such ve year period the product is returned prepaid, with proof of purchase date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melvile, New York 11747. This warranty excludes and there is disclaimed liability for
labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or
implied warranties of any kind, including merchantability and fitness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityand tnessforaparticularpurpose,islimitedtoveyears.Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation.Theremediesprovidedherein aretheexclusiveremediesunderthis warranty, whetherbasedon contract,tort or otherwise.
Programming Instructions (cont’d):
Step 5 Step 8
• Positionallwirestoprovide
roominoutletwallboxfor
WSS10.
• Ensurethattheword“TOP”
isfacinguponWSS10strap.
• Partiallyscrewinmounting
screwsinwallboxmounting
holes.
Testing your WSS10 prior to mounting in
wall box:
NOTE:Dresswireswithabendasshownindiagraminordertorelieve
stresswhenmountingWSS10.
• Restorepoweratcircuitbreakerorfuse.
• PresspaduntillocatorLEDisOFF.
LightsshouldturnON.
If lights do not turn ON, refer to the
TROUBLESHOOTING section.
Step 6
Installationmaynowbe
completedbytightening
mountingscrewsintowall
box.Attachwallplate.
Switch Mounting:
TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.
Step 7
Troubleshooting
• LightsFlickering
 - IflightsareickeringintheOFFstate,checktoinsureminimumload
requirementsaremet.
• OccupancySensor
• Sensor turns lights back on right after they turn OFF
  - Adjustrange(CCW)slightlytoreducerangeorrelocateSensor
fartherawayfromlightorheatsource.
• FalseTrippingwhennooneisaround
  - Adjustrange(CCW)slightlytoreducesensitivity,relocateSensor
closertolightsource,orre-conguresensortoMANUALONmode.
Operation
NOTE: The locator LEDwillilluminatewhentheloadisintheOFFposition
tofacilitateaccessinthedark.
Push Pad (Default settings)
Turn ON from OFF position:
Tap–LightsturnON.
Turn OFF from ON position:
Tap–LightsturnOFF.
Cleaning:Cleanwithadampcloth.DO NOTusechemicalcleaners.
Technical Notes:
• DisabletheWalkThrufeature(turnDipSwitchOFF)
• TheNoNeutralswitch(WSS10-GD)decreasesyourrangebyabout20feet
(designrestrictionwhennothavingneutralavailabletoworkwith)
• Inanindoorenvironment,thewirelesscontrolshaveatypicalrangeof30-150
feet.Astheobstructionsand/ornoiseinterferenceislighterorheaviertherange
willbemoreorless.
• Noiseinterferencecanbeeitherlinenoise(frommotors)orRadioFrequency(RF)
• Switchesgointoareducedrangemodewheninprogramming(under15feet)
• Rangecanbereducedbyoverloadingtheswitch(switchisonlyratedat10A)
• Rangecanbereducedbymetalobjects(metaldecreasestheeffectivenessof
RFtransmission)
• OutputpowerisregulatedbytheFCC
• Receiversensitivityisxed
• FixedAntennasareintegratedintotheproduct
Consider Factors affecting the Environment:
• deviceplacement
• obstructions(metal,concrete,otherconstructionmaterials)
• interference
Momentary Mode Programming Instructions
(LED flashing amber 2x per second)
1. ReadallRocker Mode programming stepsbeforetakinganyactionto
programthereceiverinMomentaryMode.
2. WhilethereceiverisintheModeSelectionArea(AmberLEDash1xper
second).ToadvancetoMomentaryMode(LEDashingamber2xpersecond),
pressthereceiverswitchbuttontoadvancetheAmberLEDtoashing2xper
second(MomentaryMode).
3.ToLearnatransmitterswitchinMomentaryModepressandholdthebuttonfor
5seconds.TheLEDwillchangefromAmbertoGreen*orRed**tosignifyyou
arenowintheLearnareaofprogramming.Releasethebutton.
4. Follow Steps 4-7 of “Rocker Mode Programming Instructions.”
Toggle Mode Programming Instructions
(LED flashing amber 3x per second)
1. ReadallRocker Mode programming stepsbeforetakinganyactionto
programthereceiverinToggleMode.
2. WhilethereceiverisintheModeSelectionArea(AmberLEDash1xper
second).ToselectToggleMode,pressthereceiverswitchbuttontoadvancethe
AmberLEDtoashing3xpersecond(ToggleMode).
3. ToLearnatransmitterswitchinToggleModepressandholdthebuttonfor5
seconds.TheLEDwillchangefromAmbertoGreen*orRed**tosignifyyouare
nowintheLearnareaofprogramming.Releasethebutton.
4. Follow Steps 4-7 of “Rocker Mode Programming Instructions.”
Scene Mode Programming Instructions
(LED flashing Amber 4x per second)
1. ReadallRocker, Momentary, and Toggle Mode programming stepsbefore
takinganyactiontoprogramthereceiverinSceneMode.
2. Beforeprogramminga“scene”,havethedesiredsceneplannedoutandknow
thestateinwhicheachloadwillneedtobe(ONorOFF).
3. ForallloadsinthescenethatwillbeON,programthecorrespondingreceiver
orreceiveroutputwithawirelesslightswitchinRockerMode(Refer to “Rocker
Mode Programming Instructions”).
4. TurnONallofthedesiredloadsthatwillbeONinthescene
(allotherloadsOFF).
5. Foreachloadinthescene,withthereceiverorreceiveroutputconnected
totheloadandinToggleMode,pressandholdthereceiverbuttonforabout
3seconds.ThisactivatesSceneMode.Theelectricalloadconnectedtothe
receiverorreceiveroutputwillpausebriey,thencontinueturningONandOFF
inafastpattern.
6. Foreachloadinthescene,whiletheconnectedreceiverorreceiveroutput
isinSceneMode,presstheendofatransmitterswitchrockerthatwillactas
thescenebutton.TheloadwillstayONforabout3secondsindicatingthatthe
receiverhasstoredthetransmitter’suniqueIDinitsmemory.
7. ForeachloadinthescenethatwillbeON,andwasprogrammedinRocker
Mode(See Step 3 of “Scene Mode Programming Instructions”),selectively
deletetheswitchfromRockerMode.Whilethereceiverorreceiveroutput
connectedtotheloadisstillinSceneMode,enterintoRockerModeby
pressingthereceiverbuttontoexitscenemode(LEDwillnowashamber),
thenpressthereceiverbuttonandadvancetheLEDtoRockerMode(LED
ashing1xpersecond)(see “Clear One Transmitter from Programming
Mode”)todeletethetransmitterswitch’sIDfrommemory.
8. ToexitLearnMode,justwait;thereceiverautomaticallyexitsLearnModeafter
30seconds(indicatedbytheceasingofthetogglingoftheelectricalload).
Selective Deleting:FollowtheLearnModestepsabovetodeleteatransmitter
fromareceiver’smemory.Uponpressingthebuttononthedesiredtransmitter
(See “Rocker Mode Programming Instructions”, Step 4)theloadwillstay
OFFindicatingthatthereceiverhasremovedthetransmitter’suniqueIDfromits
memory.
Clear All:AdvancetheAmberLEDtoashing5xpersecond,pressandholdthe
receiverswitchbuttonfor5secondstoentertheClearArea.Releasethebutton.To
CLEARALLdevicesfrommemorypressthereceiverswitchbuttonfor5seconds
again.Theentirememoryofthereceiverwillbedeleted.ThereceiverLEDwillash
Red**andthenexitprogramming.
Clear One Transmitter from Programming Mode:FirstenterProgramming(See
steps 1-3 of “Programming Instructions”),thenrepeatedlypressthebuttonto
advancetheAmberLEDashesuntilthedesiredModeisreached.EntertheLearn
Modebypressingandholdingthereceiverbuttonfor5seconds.Releasethebutton.
TheLEDwillashfromAmbertoGreen**orRed**tosignifyyouarenowinthe
Learnareaofprogramming.Holddownthetransmitterswitchbutton(orsensorlearn
button)youwishtounlearn.Releasethebutton.Thiswillclearthetransmitterfromthe
memoryforthatprogrammingmode,leavingtheotherprogrammingmodesintact.
* Green LED flashing indicates transmitters are Learned, the number of
flashes represents the number of transmitters learned in that Programming
Mode.
** Red LED flashing indicates there are no transmitters learned.
Obstructions:
• Doesthesystemworkmorereliablyatcloserange(withoutobstructions)?
• Identifynearbymetal,concreteandotherobjectspossiblyaffecting
signalstrength
• Caneitherdeviceberelocated(evenslightly)awayfromobstructionsto
improvethesystemperformance?
Interference:
• Doesthesystemworkbetteratcertaintimesoftheday?
• Lookforpiecesofequipmentthatmayaffectwirelessperformancewhen
theyareON
• Tryusingasignalstrengthmetertomeasure315MHz(RF)noiseoorand
quantifypacketreceivingreliability
Product variations:
• Replaceonepieceofhardwareatatimetoisolateanyvariationin
productperformance
Dip Switch Settings:
• VerifyproperdipswitchsettingsontheReceiverSwitch
• DipSwitch1:Intheleftposition(off)isAuto-On;intherightposition(on)
isManual-On
• DipSwitch2:Intheleftposition(off)forWalkThroughOff
• DipSwitch3and4:Thesesetthetimedelay;bothintheleftposition(off)
willbea2minute(test)timedelay
Product LED indicators:
• OccupancySensorLED:MakesureLEDashesredonceevery60seconds
toverifypackettransmission
• ReceiverSwitchLED:MakesureLEDlocatorashesredverifyingreception
ofapacketfromSensororRemote
• Verifycorrectprogrammingofdevice(s)usingtheReceiverSwitch
• Enterprogrammingandgotolearnmode
• VerifyashinggreenLEDlocatorwhichsigniesdevicelearned
• Pressthelearnbuttononthetransmitterdevicetounlearnthedevice,green
LEDshouldashonelessorthereshouldbearedLED(nodeviceslearned)
• Pressthetransmitterdevicetorelearnthedeviceaddressagain
• GreenLEDlocatorshouldashagainforthenumberofdevicesprogrammed