Pakedge Device & Software SE-8P4 User manual

pakedgedevice&softwareinc
SE-8P4
8 Port Gigabit Unmanaged Switch with 4 Ports PoE or 2
Ports PoE+
User Manual- Version 1.0

FCC Certifications
This Equipment has been tested and found to comply with the limits for a
Class Bdigital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to the EMC
Directive 2004/108/EC, the Low Voltage Directive 2006/95/EC, and the
RoHS Directive 2011/65/EU.
Company has an on-going policy of upgrading its products and it may be
possible that information in this document is not up-to-date. Please check
with your local distributors for the latest information. No part of this
document can be copied or reproduced in any form without written consent
from the company.
Trademarks:
All trade names and trademarks are the properties of their respective
companies.
Copyright © 2015, All Rights Reserved.

1
Unpacking Information
Thank you for purchasing the Pakedge Device & Software SE-8P4 gigabit switch.
Before installation, please verify that your package contains the following items.
1. One 8-Port Gigabit Ethernet with 2-Port PoE+/4-Port PoE Switch
2. One AC power cord
3. Rubber feet and screws
4. Rack-mount brackets and screws (included, optional use)
5. User Manual
Introduction
General Description
The SE-8P4 provides 8*10/100/1000Mbps Gigabit ports with 4-port PoE+/PoE,
making it an excellent choice for a fast, cost effective and reliable networking
infrastructure. The store-and-forward architecture filters errors and forwards packets
in a non-blocking environment. Flow control ensures the accuracy of the data
transmitted. The PoE+ on the SE-8P4 supplies power for connected devices that
need it. Over current protection and circuit shorting protection are also supported.
The switch was designed for easy installation and maintenance. It supports the
Nway auto-negotiation protocol that detects networking speed (10/100/1000 Mbps)
and duplex modes (Full/Half) automatically. Auto-MDI/MDI-X function alleviates the
need for crossover cables. Also, rich diagnostic LEDs are provided for real-time
connection status information.
Key Features
Complies with 10BASE-T specifications of the IEEE802.3 standard
Complies with 100BASE-TX specifications of the IEEE802.3u standard
Complies with 1000BASE-T specifications of the IEEE802.3ab standard
Compliant with IEEE 802.3af/at PoE standard (DTE power via MDI)
Provides 4 PoE ports with classification identify
Supports 15.4W maximum per PoE port
Supports 31.5W maximum per PoE+ port
Supports over current protection and circuit shorting protection
8 * RJ-45 ports for 100BASE-TX and 1000 BASE-T and 10BASE-T connectivity
Provides8* 10/100Mbps auto-detect（half/full）and 1000Mbs full duplex switch

2
ports(IEEE802.3/ 802.3u/ 802.3ab)
Supports MDI/MDI-X auto crossover
Supports 63W Max;
Full load: 31.5W(at) x 2P = 63W
15.4W(af) x 4P = 61.6W
Wire-speed packet filtering and forwarding rate
Store-and-forward architecture filters fragment & CRC error packets
Supports extensive LED indicators for network diagnostics
Internal universal switching power supply
The Front Panel
The front panel consists of LED indicators. For detailed LED definition, please refer
to the next paragraph.
LEDs Definition
System LED
LED
Status
Operation
Power
Steady Blue
The switch is powered on
Off
The switch is powered off
Loop
Blinking Red
Off
There is a loop
There is no loop
Port LEDs
LED
Status
Operation
Link/ACT
Steady Blue
Valid port connection.
Blinking Blue
Valid port connection and there is data t
transmitting/ receiving
Off
Port disconnected or the port is connected at 10
Mbps or 100 Mbps
PoE
Steady Blue
A PoE compliant devices is connected to the port
Off
No PoE complaint device is connected to the port

3
Power Receptacle
To be compatible with the varying electric service standards around the world, the
switch comes with a power supply which can operate from 100 to 240VAC, 50/60Hz.
Please make sure that your outlet standard is within this range.
To power on the switch, plug the female end of the power cord firmly into the
receptacle of the switch and the other end into an electric service outlet. After the
power cord installation, toggle the ON/OFF switch into the ON position and please
check if the power LED is illuminated to ensure normal operations.
Rear Panel
Installation
This switch can be placed on your desktop directly, or mounted in a rack. The
installation is simple. Users can utilize all the features of the switch just by attaching
the appropriate cables and turning the power on.
Before installing the switch, we strongly recommend:
1. The switch is placed in a well ventilated environment. A minimum of 25mm (1
inch) space around the unit is recommended.
2. The switch and the relevant components are away from electrical noise
sources such as radios, transmitters and broadband amplifiers
3. The switch is not placed in a high humidity or moist environment.
Desktop Installation
1. Attach the provided rubber feet to the bottom of the switch to keep the switch
from slipping. The recommend position is square-marked.
2. Install the switch on a level surface that can support the weight of the unit
and the relevant components.
3. Plug the switch with the female end of the provided power cord and plug the
male end into the power outlet.

4
Rack-mount Installation
Rack mounting facilitates an orderly installation when a series of networking devices
are installed. The switch is supplied with rack mounting brackets and screws
Procedures to Rack-Mount the Switch:
1. Disconnect all the cables from the switch before continuing.
2. Place the unit on a hard, flat surface with the front facing you.
3. Place a mounting bracket over the mounting holes on one side of the
unit.
4. Insert the screws and fully tighten with a suitable screwdriver.
5. Repeat the two previous steps for the other side of the unit.
6. Insert the unit into the rack and secure with suitable screws.
7. Reconnect all the cables.
Network Cables Installation
1. Crossover or straight-through cable: All the ports on the switch support
Auto-MDI/MDI-X functionality. Both straight-through or crossover cables can
be used to connect the switch with PCs as well as other devices like
switches, hubs or router.
2. Category 3, 4, 5 or 5e UTP/STP cable: To make a valid connection and
obtain the optimal performance use the appropriate cables corresponding to
different transmitting/receiving speed. To choose a suitable cable, please
refer to the following table.
Media
Speed
Wiring
10/100/1000Mbps copper
10Mbps
Category 3,4,5 UTP/STP
100Mbps
Category 5 UTP/STP
1000Mbps
Category 5,5e UTP/STP
Port Operation
The auto-negotiation feature allows ports running at one of the following
operation modes:
Media
Speed
Duplex Mode
10/100/1000Mbps(copper)
1000Mbps Fiber (Mini GBIC required)
10Mbps
Full Duplex
Half Duplex
100Mbps
Full Duplex
Half Duplex
1000Mbps
Full Duplex

5
Product Specifications
Standard
IEEE802.3 10BASE-T
IEEE802.3u 100BASE-TX
IEEE802.3x full-duplex flow control
IEEE802.3ab 1000BASE-T
IEEE 802.3af/at PoE standard (DTE power via MDI)
Interface
8*10/100/1000 Mbps auto MDI/MDI-X RJ-45 switching ports
Supports 63W Max;
Full load:
31.5W(at) x 2 Ports
15.4W(af) x 4 Ports
Cable Connections
RJ-45 (10BASE-T): Category 3,4,5 UTP/STP
RJ-45 (100BASE-TX): Category 5 UTP/STP
RJ-45 (1000BASE-T): Category 5,5e or enhanced UTP/STP
Transmission Mode
10/100Mbps Full-duplex, Half-duplex
1000Mbps Full-duplex
LED indications
1 * power LED
8 * Link/ACT LEDS
4 * PoE LEDS
1 * loop LED
Memory
8K MAC entries
9216 bytes jumbo packet length
128K bytes Buffer Memory
Emission
FCC & CE
Safety
LVD
Operating
Temperature 00~ 400C (320~ 1040F)
Operating Humidity
10% - 90%(non-condensing)
Power Supply
Internal power supply
100-240V/47-63 Hz universal input
Dimensions & Weig
12.68” x 7.31” x 1.75”
4.3 lbs.

6
Technical Support
Please visit our website for up-to-date support information:
Website: www.pakedge.com
Email: [e-mail]
CONTACT INFORMATION:
Pakedge Device & Software Inc.
3847 Breakwater Avenue
Hayward, CA 94545-3606
USA
877-274-6100
© Pakedge Device & Software Inc. 2015 – All Rights Reserved