Levoit LV-H133 User manual

Questions or Concerns?
[email protected]
Tower HEPA Air Purifier
Model No.: LV-H133
ENGLISH • DEUTSCH

2
Package Contents
Specifications
Safety Information
Getting to Know Your Air Purifier
LED Display
Getting Started
·About the Safety Trigger
Operation
·General Operation
·Button Controls & Functions
·Air Quality Indicator
·Memory Function
Keeping Things Clean
·When Should I Replace the Air Filter?
·Replacing the Air Filter
·Purchasing a New Air Filter
·Resetting the Air Purifier
·Cleaning the Dust Sensor
Troubleshooting
Warranty Information
Lieferumfang
Spezifikationen
Sicherheitsinformationen
Lernen Sie Ihren Luftreiniger Kennen
Led-Anzeige
Erster Schritt
·Über den Sicherheitsauslöser
Bedienung
·Allgemeine Bedienung
·Tastensteuerung & Funktionen
·Luftqualitätsanzeige
·Speicherfunktion
Reinigung
·Wann sollte ich den Luftfilter
austauschen?
·Auswechseln des Luftfilters
·Kauf eines neuen Luftfilters
·Zurücksetzen des Luftreinigers
·Reinigung des Staubsensors
Problembehandlung
Garantie
3
3
4
5
5
6
7
7
7
8
9
9
9
9
10
11
11
11
12
14
16
16
17
18
18
19
20
20
20
21
22
22
22
22
23
24
24
24
25
27
TABLE OF CONTENTS INHALTSVERZEICHNIS
English Deutsch
EN DE

3
EN
SPECIFICATIONS
1 x LV-H133 Tower HEPA Air Purifier
1 x Filter (Pre-installed)
1 x User Manual
1 x Caution Card
PACKAGE CONTENTS
Power Supply AC 220-240V, 50/60Hz
Rated Power 33W
Applicable Area ≤ 50 m² (538 ft²)
Operating Conditions
Temperature: -10°C~55°C
(14°F~131°F)
Humidity: ≤ 95% RH
Noise Level ≤ 54dB
CADR
(Clean Air Delivery Rate) 400 m³/h (235 CFM)
Standby Power < 0.8W
English
Tower HEPA Air Purifier
Model No.: LV-H133
Français
Español
Italiano

4
EN
SAFETY INFORMATION
Always follow the instructions and safety guidelines in this manual.
Only use your Levoit Tower HEPA Air Purifier as described in this manual.
• Place the air purifier on a flat, level, solid surface before operation.
• DO NOT place the air purifier near sources of heat, such as open
flames, stove tops, ovens, radiators, or computers.
• DO NOT route the cord under carpeting, rugs, furniture, or appliances.
Place the power cord away from high-trac areas.
• This product is suitable for use with solid-state speed controls (such
as dimmer switches).
• DO NOT use an extension cord with this unit.
• DO NOT sit on or place anything on top of the air purifier.
• DO NOT place the air purifier directly below an air conditioner, to
prevent any moisture from getting into the air purifier.
• This air purifier should be inspected frequently. Dirt that has collected
should be removed regularly to prevent excessive accumulation that
may result in a flashover or fire.
• DO NOT clean the appliance with water or any other liquid to avoid
electric shock, fires, or injury.
• If the air purifier is damaged, or is not functioning properly,
immediately stop use and contact Customer Support (page 14).
• DO NOT attempt to repair this device in any way or use any third-
party parts to modify the air purifier. Doing so will void your warranty.
Contact Customer Support immediately if your device is no longer
working.
General Safety
IMPORTANT:
Use & Care
SAVE THESE INSTRUCTIONS
• DO NOT operate if cord or plug is damaged.
• DO NOT handle with wet hands. Dry your hands before handling the
air purifier.
• DO NOT immerse the air purifier in water or liquid.
• DO NOT use the air purifier in wet or humid environments.
• DO NOT use the air purifier outdoors.
• DO NOT use the air purifier in a room with major indoor temperature
changes. This may cause condensation to build up inside the
appliance.
• DO NOT use the air purifier in an enclosed space where toxic,
flammable, combustible, or explosive gases or substances are
present.
• If you are using the air purifier where oxygen is being administered,
make sure the purifier is at least 3-5 feet away from the oxygen tank.
• DO NOT insert fingers or objects into the air outlet.
 DO NOT allow children to play on or near the air purifier.
Child supervision is required while the air purifier is on.

5
EN
1 2
3
4
5
6
7
8
910
1. LED Display
2. Air Outlet
3. Housing
4. Power Cord
5. Air Intake
6. Dust Sensor
7. Dust Sensor Cover
8. Safety Trigger
9. Filter Cover
10. Air Filter
Front Back
GETTING TO KNOW YOUR AIR PURIFIER
LED DISPLAY
Fan Speed
Button/Indicator
Fan Speed
Indicator
Timer Display
Timer
Button/Indicator
Air Quality
Indicator
Power
Button/Indicator
Auto Mode
Button/Indicator Change Filter
Button/Indicator
Sleep Mode
Button/Indicator Display Button

6
EN
GETTING STARTED
Figure 1.1
Figure 1.2
black tabs
facing out
1. Pull the handle of the filter cover to open the housing.
Remove the air filter from the housing. [Figure 1.1]
2. Take the filter out of its plastic packaging, then reinstall it into
the housing. Make sure the black pull tabs on the filter are
facing out. [Figure 1.2]
NOTE:
• If you are not planning to use the air purifier for a long period of time, we recommend leaving the filter inside
its plastic packaging until it is ready to be used. This helps prevent mold from building up on the air filter.
• If the filter cover is not properly installed, the air purifier will not turn on.
Figure 1.3
Figure 1.4
3. Replace the filter cover by aligning the bottom portion of the
cover with the inlets on the bottom of the housing. [Figure 1.3]
4. Once the bottom portion is properly aligned, slowly close the
cover by aligning its top part with the inlets at the top of the
opening. [Figure 1.4]

7
EN
About the Safety Trigger
Figure 2.1
When replacing the filter cover onto the air purifier, always make
sure the magnetic safety trigger is properly aligned with its
respective area. [Figure 2.1]
OPERATION
General Operation
1. Place the air purifier on a level surface. [Figure 3.1]
2. Plug the air purifier into a powered electrical outlet.
3. Tap to turn on the air purifier. It will start operating at
medium speed.
4. (Optional) Tap to adjust the fan speed of the air purifier.
There are 3 fan speeds to choose from (see Button Controls
& Functions, page 8).
5. Tap to turn o the air purifier when you are finished
using it.
NOTE: Always allow at least 15 inches (38 cm) of clearance on all sides
of the air purifier. [Figure 3.2]
Figure 3.1
Figure 3.2
NOTE: If the trigger is not properly aligned, the air
purifier will not turn on.
safety trigger makes
contact with the base
38 cm

8
EN
Button Controls & Functions
Power Button
Turns the air purifier on or o.
Fan Speed Button
Tap to cycle through the adjustable fan speeds
of the air purifier: low, medium, and high (see Chart
A below).
Fan Speed Indicator Fan Speed
Low
Medium
High
NOTE:
• The fan speed cannot be adjusted while on Auto or Sleep Modes.
• To eectively clean the air, make sure to keep your windows closed
while the air purifier is operating.
• For best results, it is recommended to run the air purifier at maximum
speed for 15–20 minutes before using a lower speed setting or setting
the air purifier to Auto Mode.
Chart A
Auto Mode Button
Tap to activate the Auto (automatic) Mode on
the air purifier. This mode automatically adjusts the
fan speed of the air purifier according to the current
air quality. The air quality indicator around the LED
display will also illuminate a certain color based on
the air quality and fan speed (see Chart B below).
Sleep Mode Button
Tap to activate Sleep Mode on the air purifier. This
function sets the air purifier to its lowest speed setting
to create a quiet environment while producing clean air.
Display Button
Turns the LED Display on or o while the air purifier is
operating.
NOTE: While the display is o, you can tap any button
(except ) to turn on the display.
Indicator Color Air Quality Fan Speed
Blue Very Good Sleep Mode
Green Good Low
Orange Moderate Medium
Red Bad High
Chart B
Timer Button
Allows you to program a timer for 1–12 hours.
1. Tap repeatedly to choose a time.
2. Once you have reached the desired time, the
timer display will flash 5 times before setting.
3. The air purifier will automatically power o once
the timer has finished counting down.
4. To cancel the timer, tap repeatedly until
the timer display reads “- - - -”. Wait until “- - - -”
flashes 5 times to exit out of the timer function.
NOTE:
• To quickly select a time, press and hold for 2
seconds, or until the desired time appears on the
timer display.
• The timer function will remember your previously
programmed time when you press .
• The timer function is available for all modes.

9
EN
Air Quality Indicator
Memory Function
Chart C
Outside of Auto Mode, the air quality indicator will also light up to
denote the current air quality during normal operation. [Chart C]
The air purifier will remember its programmed settings when
turned o and resume these settings when turned back on.
NOTE: The memory function will not remember the programmed time.
NOTE: It will take 30 seconds for the air purifier to detect the air quality
each time it is turned on. The air quality indicator will always light
up blue when the air purifier is first turned on. After 30 seconds,
the color of the indicator will change based on the detected air
quality.
Indicator Color Air Quality
Blue Very Good
Green Good
Orange Moderate
Red Bad
KEEPING THINGS CLEAN
This indicator will light up red to remind you to check the air filter.
How soon turns on depends on how often you use your air
purifier. It does not necessarily mean it is time to change the filter.
Change Filter Indicator
It is recommended that you change the air filter every 6–8 months.
However, the time may vary depending on the frequency of use
and the air quality in the room. It is important to watch out for the
following signs of an expired filter:
• Increased operating noise
• Decreased airflow
• Clogged filter
• Increased presence of odors
NOTE:
• The environment in which the air purifier is being used may also
extend or shorten the lifetime of the air filter. Using your air purifier in
an environment of relatively high pollution may mean you will need to
change the air filter more often.
• If the air pollution in your environment is very high, there is a possibility
that the filter may not be completely eective and may need to be
replaced before the indicator lights up on the display.
• Remember to reset the air purifier after changing the air filter.
When Should I Replace the Air Filter?
NOTE: It is recommended to clean the pre-filter with a brush or vacuum
each month to prevent buildup of hair or dust.

10
EN
1. Turn o and unplug the air filter, then remove the filter cover.
[Figure 4.1]
Replacing the Air Filter
2. Remove the old air filter and properly dispose of it.
[Figure 4.2]
3. (Optional) Clean any remaining dust and dirt from inside the
housing using a vacuum hose. [Figure 4.3]
4. Unwrap the new air filter and place it into the housing. Make
sure the black pull tabs are facing out. [Figure 4.4]
Figure 4.1
Figure 4.2
Figure 4.4
Figure 4.3
black tabs
facing out
unplug
air purifier
5. Replace the back cover onto the housing. [Figure 4.5]
6. Plug in and turn on the air purifier. Then press and hold for
3 seconds (see Resetting the Air Purifier, page 11).
NOTE:
• Do not clean the filter with water or other liquid.
• The back cover must be properly secured to the unit in order for it to
power on.
Figure 4.5

11
EN
Resetting the Air Purifier
It is necessary to reset the air purifier after changing the air filter.
There are two scenarios where you must reset the air purifier:
• Scenario 1: lights up red.
1. Replace the air filter (see Replacing the Air Filter,
page 10).
2. Press and hold for 3 seconds.
3. The indicator light will turn o. This means that the air
purifier has been successfully reset.
• Scenario 2: The air filter was changed before
lights up.
1. Press and hold for 3 seconds.
2. The air purifier will chime to indicate that it has been
successfully reset.
Cleaning the Dust Sensor
Figure 5.1
The dust sensor uses an infrared light to detect airborne
particles. Accumulated dust, after a prolonged period of use, will
aect the sensitivity of the sensor. If this occurs, your air purifier
will continue to run on high speed while operating on Auto Mode,
and will not adjust itself to a lower speed setting.
1. Turn o and unplug the air purifier.
2. Open the dust sensor cover.
3. Use a cotton swab dipped in clean water to clean the
lens.
4. Dry the lens with a clean cotton swab. [Figure 5.1]
5. Close the dust sensor cover.
lens inside
opening
Purchasing a New Air Filter
To maintain your health and product performance, please only
use ocial Levoit replacement filters. You can purchase new air
filters from Amazon.co.uk by searching for “B07FXB5P8R”. You
can also scan the QR code below.
If you have any questions, please contact Customer Support
(page 14).

12
EN
TROUBLESHOOTING
Problem Cause Solution
Air purifier does not power on. Unit is not plugged into an electrical outlet. Connect the plug to a powered electrical
outlet.
Outlet is not working properly. Try plugging the air purifier into a dierent
outlet.
Filter cover is not properly placed on the unit. Properly replace the filter cover (see Getting
Started, page 6).
Power cord is damaged. Immediately discontinue use and contact
Customer Support (page 14).
Air purifier is defective or malfunctioning.
Air purifier does not respond to
button controls.
Air purifier is not plugged into an outlet. Connect the plug to a powered electrical
outlet.
Filter cover is not properly placed on the unit. Properly replace the filter cover (see Getting
Started, page 6).
Air purifier is defective or malfunctioning. Immediately discontinue use and contact
Customer Support (page 14).
After turning on Auto Mode, the
air purifier always runs on the
highest fan speed.
The air in the surrounding environment is still dirty. Allow the air purifier to continue running at
high speed until the air quality in the room
improves.
There is dust on the lens of the dust sensor. Clean the dust sensor (see Cleaning the Dust
Sensor, page 11).
Air purifier makes an unusual
noise while operating.
Air filter needs to be replaced. Replace the air filter (see Replacing the Air
Filter, page 10).
Filter does not fit properly. Properly place the filter (see Getting Started
and Replacing the Air Filter, page 6 and
page 10).
Foreign object inside the unit. Immediately discontinue use and contact
Customer Support (page 14). DO NOT
attempt to open the air purifier.
Significantly reduced airflow. Filter packaging has not been removed. Remove the filter from its packaging before
use.
Fan speed is low. Press to adjust fan speed.
Filter needs to be replaced. Replace the air filter (see Replacing the Air
Filter, page 10).
Not enough clearance on all sides of the purifier. Ensure there is at least 38 cm (15 inches) of
clearance on all sides of the purifier.

13
EN
Problem Cause Solution
Poor air purification quality. Room is larger than the air purifier’s applicable
area.
Ensure the room is smaller than 50 m²
(538 ft²).
Air intake or outlet is blocked. Remove objects blocking air intake or outlet.
Filter is not properly placed inside the housing. Properly place the filter (see Getting Started
and Replacing the Air Filter, page 6 and
page 10).
The air filter is dirty and cannot produce fresh air
anymore.
Replace the air filter (see Replacing the Air
Filter, page 10).
Not enough clearance on all sides of the purifier. Ensure there is at least 38 cm (15 inches) of
clearance on all sides of the purifier.
The air purifier is producing an
unpleasant odor.
The air filter is dirty and cannot produce fresh air
anymore.
Replace the air filter (see Replacing the Air
Filter, page 10).
High humidity levels have caused mildew to grow
on the air filters.
Replace the air filter, and move the air purifier
to a room where the relative humidity is less
than 85% RH.
is still illuminated after
replacing the air filter.
The air purifier has not been reset. Reset the unit (see Resetting the Air Purifier,
page 11).

14
EN
WARRANTY INFORMATION
TERMS & POLICY
Levoit warrants all products to be of the highest quality in material,
craftsmanship and service for a minimum of 2 years, eective
from the date of purchase. Warranty lengths may vary between
product categories. Should you encounter any issues or have any
questions regarding your new product, feel free to contact our
helpful Customer Support Team. Your satisfaction is ours!
Importer: Adiman B.V.
Address: Steenovenweg 5, Place for Bizz Helmond, 5708HN
Helmond, NL
Email: [email protected]
* Please have your order number ready before contacting
customer support.

16
DE
SPEZIFIKATIONEN
1 x LV-H133 HEPA Luftreiniger-Turm
1 x Filter (Vorinstalliert)
1 x Bedienungsanleitung
1 x Vorsicht Karte
LIEFERUMFANG
Deutsch
HEPA Luftreiniger-Turm
Modell Nr.: LV-H133
Stromspannung AC 220-240V, 50/60Hz
Nennleistung 33W
Anwendungsbereich ≤ 50 m² (538 ft²)
Betriebsbedingungen
Temperature: -10°C~55°C
(14°F~131°F)
Humidity: ≤ 95% RH
Geräuschpegel ≤ 54dB
CADR (Reinluftfördermenge) 400 m³/h (235 CFM)
Standbyleistung < 0.8W

17
DE
SICHERHEITSINFORMATIONEN
Befolgen Sie immer die Anweisungen und Sicherheitshinweise in diesem Handbuch.
Verwenden Sie Ihren HEPA-Luftreiniger-Turm von Levoit nur wie in diesem Handbuch beschrieben.
• Stellen Sie den Luftreiniger vor dem Betrieb auf eine flache, ebene,
feste Oberfläche.
• Den Luftreiniger NICHT in der Nähe von Wärmequellen, wie oenen
Flammen, Herdplatten, Öfen, Heizkörpern oder Computern platzieren.
• Legen Sie das Kabel NICHT unter Teppiche, Möbel oder Geräte.
Legen Sie das Kabel weg von stark frequentierten Bereichen.
• Dieses Produkt eignet sich für den Einsatz mit Festkörper
Drehzahlreglern (z. B. Dimmschalter).
• Verwenden Sie bei diesem Gerät KEIN Verlängerungskabel.
• Setzen Sie sich NICHT auf den Luftreiniger und stellen Sie nichts
darauf.
• Stellen Sie den Luftreiniger NICHT direkt unter eine Klimaanlage, um
zu verhindern, dass Feuchtigkeit in den Luftreiniger eindringt.
• Dieser Luftreiniger sollte regelmäßig überprüft werden. Schmutz sollte
regelmäßig entfernt werden, um eine übermäßige Ansammlung zu
vermeiden, da diese zu einem Überschlag oder Brand führen kann.
• Reinigen Sie das Gerät NICHT mit Wasser oder einer anderen
Flüssigkeit, um einen elektrischen Schlag, Brände oder Verletzungen
zu vermeiden.
• Wenn der Luftreiniger beschädigt ist oder nicht richtig funktioniert,
stellen Sie den Betrieb sofort ein und wenden Sie sich an den
Kundendienst (Seite 27).
• Versuchen Sie NICHT, dieses Gerät in irgendeiner Weise zu
reparieren oder Teile von Drittanbietern zu verwenden, um den
Luftreiniger zu modifizieren. Dadurch erlischt Ihre Garantie. Wenden
Sie sich sofort an den Kundendienst, wenn Ihr Gerät nicht mehr
funktioniert.
Allgemeine Sicherheit
WICHTIG:
Verwendung & Pflege
BEWAHREN SIE DIESE
ANWEISUNGEN AUF
• NICHT benutzen, wenn das Kabel oder der Stecker beschädigt sind.
• NICHT mit nassen Händen bedienen. Trocknen Sie Ihre Hände vor
dem Bedienen des Luftreinigers.
• Den Luftreiniger NICHT in Wasser oder Flüssigkeit tauchen.
• Den Luftreiniger NICHT in nasser oder feuchter Umgebung benutzen.
• Den Luftreiniger NICHT im Freien verwenden.
• Den Luftreiniger NICHT in einem Raum mit starken
Temperaturschwankungen benutzen. Dadurch kann sich im Inneren
des Gerätes Kondenswasser bilden.
• Den Luftreiniger NICHT in einem geschlossenen Raum verwenden, in
dem giftige, brennbare, oder explosive Gase oder Stoe vorhanden
sind.
• Wenn Sie den Luftreiniger an Orten verwenden, wo mit Sauersto
gearbeitet wird, dann stellen Sie den Luftreiniger mindestens 1- 1,5
Meter vom Sauerstotank entfernt auf.
• NIEMALS Finger oder Gegenständen in den Luftauslass einführen.
• NIEMALS Kinder am oder in der Nähe des Luftreinigers spielen
lassen. Kinder müssen beaufsichtigt werden, während der Luftreiniger
eingeschaltet ist.

18
DE
1 2
3
4
5
6
7
8
910
1. LED-Anzeige
2. Luftauslass
3. Gehäuse
4. Stromkabel
5. Lufteinlass
6. Staubsensor
7. Staubsensorabdeckung
8. Sicherheitsauslöser
9. Filterabdeckung
10. Luftfilter
Vorderseite Rückseite
LERNEN SIE IHREN LUFTREINIGER KENNEN
LED-ANZEIGE
Lüftergeschwindigkeits-
Taste-Anzeige
Lüftergeschwindigkeits-
Anzeige
Timer-Anzeige
Timer-
Taste-Anzeige
Luftqualitäts-
anzeige
Netzschalter-
Anzeige
Auto-Modus-
Taste-Anzeige Filterwechsel- Taste-Anzeige
Schlafmodus-
Taste-Anzeige Anzeige-Taste

19
DE
ERSTER SCHRITT
Abbildung 1.1
Abbildung 1.2
Schwarze
Laschen
nach
außen
gerichtet
1. Ziehen Sie am Gri der Filterabdeckung, um das Gehäuse
zu önen. Nehmen Sie den Luftfilter aus dem Gehäuse.
[Abbildung 1.1]
2. Nehmen Sie den Filter aus der Kunststoverpackung und
setzen Sie ihn wieder in das Gehäuse ein. Stellen Sie sicher,
dass die schwarzen Zuglaschen am Filter nach außen
zeigen. [Abbildung 1.2]
HINWEIS:
• Wenn Sie den Luftreiniger über einen längeren Zeitraum nicht benutzen möchten, empfehlen wir, den Filter in seiner Kunststoverpackung
zu lassen, bis er wieder benutzt werden soll. Dadurch wird verhindert, dass sich Schimmelpilze auf dem Luftfilter ansammeln.
• Wenn die Filterabdeckung nicht richtig angebracht ist, lässt sich der Luftreiniger nicht einschalten.
Abbildung 1.3
Abbildung 1.4
3. Setzen Sie den Filterdeckel wieder auf. Richten Sie den
unteren Teil des Deckels an den Einlässen an der Unterseite
des Gehäuses aus. [Abbildung 1.3]
4. Sobald der untere Teil richtig ausgerichtet ist, schließen
Sie den Deckel langsam, indem Sie den oberen Teil mit
den Einlässen an der Oberseite der Önung ausrichten.
[Abbildung 1.4]

20
DE
Über den Sicherheitsauslöser
Abbildung 2.1
Achten Sie beim Aufsetzen der Filterabdeckung auf
den Luftreiniger immer darauf, dass der magnetische
Sicherheitsauslöser richtig am jeweiligen Bereich ausgerichtet ist.
[Abbildung 2.1]
BEDIENUNG
Allgemeine Bedienung
1. Stellen Sie den Luftreiniger auf eine ebene Fläche.
[Abbildung 3.1]
2. Schließen Sie den Luftreiniger an eine Steckdose an.
3. Tippen Sie auf , um den Luftreiniger einzuschalten. Der
Betrieb beginnt mit mittlerer Geschwindigkeit.
4. (Optional) Tippen Sie auf , um die Lüftergeschwindigkeit
des Luftreinigers einzustellen. Es stehen 3 Lüfterstufen zur
Auswahl (siehe Tastensteuerung & Funktionen, Seite 21).
5. Tippen Sie auf , um den Luftreiniger auszuschalten, wenn
Sie fertig sind.
HINWEIS: Der Luftreiniger benötigt immer einen Freiraum von mindestens
38 cm auf allen Seiten. [Abbildung 3.2]
Abbildung 3.1
Abbildung 3.2
HINWEIS: Wenn der Auslöser nicht richtig ausgerichtet
ist, lässt sich der Luftreiniger nicht einschalten.
Der Sicherheitsauslöser
hat Kontakt mit dem
unteren Teil
38 cm