LG LW1813ER User manual

TYPE WINDOW
MODEL LW1813ER
OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your air conditioner and retain it for future reference.
P/NO MFL67654301
www.lgappliances.com

LW1813ER
7
16
20
Safety Precautions
Maintenance and Service
Before Operation
Introduction
Electrical Safety
Installation
Operating Instructions

Do not store flammables like
gasoline benzene thinner
etc. near the air conditioner

No correlation between fan
usage and oxygen depletion.
Unplug the unit when not
using it for a long time.

When gas leaks, open the
window for ventilation before
operating the unit.
Be considerate.
Follow installation instructions exactly.
Hold the plug by the head
it out.
（not the cable）when taking
Never touch the metal parts
of the unit when removing
the filter.
Install the product so the exhaust and noise
are not aimed directly at the neighbors.
For inner cleaning, contact an Authorized Service Center or a dealer.
Do not use harsh detergent that causes corrosion or damage on the unit.
Harsh detergent may also cause failure of product, fire, or electric shock.

Instead of running air conditioning
constantly，open a window
for fresh air occasionally.
You will feel better.
Do not use this appliance for
special purposes such as
cooling pets foods，
precision
machinery，or objects of art
，
If the liquid from the battery gets onto your skin
or clothers，
wash it well with clean water. Do
not use the remote if the battery has leaked.
y
y
If you eat the liquid from the battery,brush
your teeth and see doctor.Do not use the
remote if the battery has leaked.

2. No correlation between fan usage and oxygen depletion.
3.

RESET
TEST
9
should be
Avoid shock hazard. This unit cannot
be user-serviced. Do NOT open the
tamper-resistant sealed portion.
All warranties and performance will
be voided. This unit is not intended
to be used as an ON/OFF switch.

Adjustable
Wrench
Installation
Foam-PE
(Adhesive-Backed)
Type C (5) Type D (2)
Type A (11)
Carriage Bolt (2) Lock Nut (4)
Type B (7)
Foam strip
(Plain-Back)
Right frame
curtain
Window locking
bracket
Left frame
curtain
Frame guide(2)
Sill
bracket (2)
Support bracket(2)
Drain joint pipe
Phillips head
screwdriver
Scissors or
knife
Flat - blade
screwdriver
11

12
Installation
All supporting parts should be secured to firm wood, masonry,
or metal.
1. This unit is designed for installation in standard double hung
windows with actual opening widths from 29" to 41".
The top and bottom window sashes must open sufficiently to
allow a clear vertical opening of 18" from the bottom of the
upper sash to the window stool.
2. The stool offset (height between the stool and sill) must be
less than 1 1/4".
NOTICE
2941
18
(Keep the screws for Iater use.)
Remove 4 screws which fasten the cabinet at both
sides and at the back.
pan
（ adhesive backed）
1.
2.
3.
4.
frame guides
（Adhesive backed）
Preparation Of Chassis
Window Requirements

10
13
A
Type
screws.
5.
6.
1. Open the window. Mark a line on the center of
the window stool
.
Loosely attach the sill bracket to the support
bracket using the carriage bolt and the lock nut.
Support
Bracket
Lock nut
Sill
Bracket
Carriage
Bolt
2. Attach the sill bracket to the window sill using
the screws (Type B).
Carefully place the cabinet on the window stool
and align the center mark on the bottom front
with the center hole marked window stool.
Screw (Type B)
Sill bracket
3. Using the screw (Type D) and the lock nut, attach
the support bracket to the cabinet track hole. Use
the first track hole after the sill bracket on the
outer edge of the window sill.Tighten the
carriage bolt and the lock nut. Be sure the
cabinet slants outward.
Cabinet
Track hole
Support
Bracket
Carriage bolt
and lock nut
Machine screw(Type D)
and lock nut
Outer edge
of window
sill
Front angle Window stool
Top
retainer
bar
Do not drill a hole in the bottom pan.The unit is
designed to operate with approximately 1/2" of
water in bottom pan.
4. Pull the bottom window sash down behind the
t op retainer bar until they meet.
frame curtain upper guide
frame guides.
Right Guide Panel
Upper guide
(Type A)
Screws
Frame guide
Left Guide panel

Installation
1. Do not pull the window sash down so tightly
that the movement of frame curtain is
restricted. Attach the cabinet to the window
stool by driving the screws (Type B) through
the cabinet into window stool.
2.The cabinet should be installed with a very
slight tilt downward toward the outside.
NOTICE
Screw(Type B)
Front Angle
Sash track
14
Pull each frame curtain fully to each window sash
track, and pull the bottom window sash down behind
the t op retainer bar until it meets.
3.
Attach each frame curtain the window sash by
using screws (Type C).
4.
5. Slide the unit into the cabinet.
For security purpose, reinstall screws
（removed from cabinet）at cabinet's sides.
See page 12.
Window locking
bracket
6.
7.
Cut the foam-strip （Not adhesive backed）
window sash and the lower window sash.
Attach the window locking bracket with a screw
(Type C).
（Not adhesive backed）
to the proper length and insert between the upper

15
Inlet Grille
Guide the lever carefully through the grille as you
push it in.
Attach the front grille to the cabinet by inserting
the tabs the grille into the slots on the front the
cabinet. Push the grille in until it snaps into place.
and secure it with a Type A screw through
Before installing the front grille, pull out
the vent control lever located above the
unit control knobs, as shown.
Put down inlet grille and take out the filter
the front grille.
8.
9.
10.

- when the air conditioner is off, it can be set to automatically turn
OPERATION MODE SELECTOR
the desired fan speed.
- when the air conditioner is on, it can be set to automatically turn
on from 1 to 24 hours at its previous mode and fan settings.
off from 1 to 24 hours.
Everytime you push this button，it will toggle between Cool，Energy Saver，Fan, and Dry.
Delay ON
Cool - Compressor runs and cools the room. Use the and FAN buttons to
set the desired temperature and circulation fan speed.
Energy Saver
Delay OFF
ON/OFF TIMER
- The fan stops when the compressor stops cooling.
Approximately every 3 minutes the fan will turn on and check the room air
temperature if cooling is needed.
Fan - Fan circulates air but compressor does not run. Use the FAN button to set
Operation starts when this button is pressed and stops when you
press the button again.
FAN SPEED SELECTOR
Use to set the fan speed to Low (F1), MED (F2), High (F3).
Power
Temp
Fan Speed
Timer Mode
REMOTE CONTROLLER
POWER

Once the set temperature is reached，the compressor and circulation fan turns off.
Dry - Dry mode is used to remove humidity from the room without additional cooling.
Fan speed is pre-set and cannot be adjusted.
TEMPERATURE CONTROL
The thermostat monitors room temperature to maintain the desired temperature.
The thermostat can be set between 60 F~86 F (16 C~30 C).
REMOTE CONTROL SENSOR
During operation in failure of electric power, the unit runs as previous setting operation.
Do not use rechargeable battery. Make sure that the batteries is new.
Do not mix alkaline, standard (Carbon-zinc) or rechargeable (Nickel-cadmium)
batteries.
- In order to prevent discharge, remove the batteries from the remote control if
the air conditioner is not going to be used for an extended period of time.
To maintain optimal operation of the remote control, the remote sensor should
not be exposed to direct sunlight.
Keep the remote control away from extremely hot or humid places.
1. Push out the cover on the back of the remote control with your thumb.
2. Pay attention to polarity and insert one new AAA 1.5V batteries.
3. Reattach the cover.
CAUTION
The remote controller will not function properly if strong light strikes the sensor of the air
conditioner or if there are obstacles between the remote controller and the air conditioner.

Adjusting horizontal air flow direction Adjusting vertical air flow direction
The horizontal direction is adjusted
by moving the lever to the left or right.
Touch the horizontal louvers to adjust
the air airflow up or down.
NOTICE
When the unit operates in extremly hot weather, it turns off automatically to protect compressor.

19
drain
base pan
base pan

Inlet Grille
1. Pull the inlet grille forward.
2. Remove the air filter from the front grille by pulling the air filter up slightly.
3. Wash the filter using lukewarm water below 40
4.Gently shake the excess water from the filter and replace.