LG THERMA V AHBW036H0 Installation guide

ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH
ΕΛΛΗΝΙΚΆ
ČEŠTINA
NEDERLANDS
POLSKI
LIMBA ROMÂNĂ
PORTUGUÊS
MAGYAR
БЪЛГАРСKN
SRPSKI
HRVATSKI SVENSKA NORSK SUOMI DANSK
EESTI KEEL
MALTI
SLOVENČINA
SLOVENŠČINA
LATVIEŠU VALODA
LIETUVIŲ KALBA
GAEILGE
МАКЕДОНСКИ
SHQIP
ÍSLENSKA BOSANSKI
QUICK MANUAL
AIR
CONDITIONER
www.lg.com
Copyright © 2015 - 2017 LG Electronics Inc. All Rights Reserved.
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring standards
by authorized personnel only.
Please retain this installation manual for future reference after reading it thoroughly.
Air-to-Water Heat Pump
Original instruction
[Representative] LG Electronics Inc. EU Representative :
LG Electronics European Shared Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen, The Netherlands
[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro,
Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA
P/NO : MFL68026605
1,MFL68026605,영영 2017. 8. 1. 영영 11:52 Page 1

Safety Precautions
2Air-to-Water Heat Pump
1. Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be fol-
lowed.
n Be sure to read before installing the unit.
n Be sure to observe the cautions specified here as they include important items related to safety.
n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classi-
fied by the following indications.
nMeanings of symbols used in this manual are as shown below.
WARNING
CAUTION
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties only.
WARNING
Be sure not to do.
Be sure to follow the instruction.
Installation
• Do not use a defective or underrated circuit breaker. Use this
appliance on a dedicated circuit.
- There is risk of fire or electric shock.
• For electrical work, contact the dealer, seller, a qualified electrician,
or an Authorized Service Center.
- There is risk of fire or electric shock.
• Always ground the unit.
- There is risk of fire or electric shock.
• Install the panel and the cover of control box securely.
- There is risk of fire or electric shock.
• Always install a dedicated circuit and breaker.
- Improper wiring or installation may cause fire or electric shock.
• Use the correctly rated breaker or fuse.
- There is risk of fire or electric.
• Do not modify or extend the power cable.
- There is risk of fire or electric shock.
• Do not install, remove, or reinstall the unit by yourself (customer).
- There is risk of fire, electric shock, explosion, or injury.
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 2

Safety Precautions
Installation Manual 3
ENGLISH
• For antifreeze, always contact the dealer or an authorized service
center.
- Almost the antifreeze is a toxic product.
• For installation, always contact the dealer or an Authorized Service
Center.
- There is risk of fire, electric shock, explosion, or injury.
• Do not install the unit on a defective installation stand.
- It may cause injury, accident, or damage to the unit.
• Be sure the installation area does not deteriorate with age.
- If the base collapses, the unit could fall with it, causing property
damage, unit failure, and personal injury.
• Do not install the water pipe system as Open loop type.
- It may cause failure of unit.
• Use a vacuum pump or inert (nitrogen) gas when doing leakage test
or purging air. Do not compress air or oxygen and do not use
flammable gases.
- There is the risk of death, injury, fire or explosion.
• Make sure the connected condition of connector in product after
maintenance.
- Otherwise, it may cause product damage.
• Do not touch leaked refrigerant directly.
- There is risk of frostbite.
Operation
• Take care to ensure that power cable could not be pulled out or
damaged during operation.
- There is risk of fire or electric shock.
• Do not place anything on the power cable.
- There is risk of fire or electric shock.
• Do not plug or unplug the power supply plug during operation.
- There is risk of fire or electric shock.
• Do not touch (operate) the unit with wet hands.
- There is risk of fire or electric shock.
• Do not place a heater or other appliances near the power cable.
- There is risk of fire or electric shock.
• Do not allow water to run into electric parts.
- There is risk of fire, failure of the unit, or electric shock.
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 3

Safety Precautions
4Air-to-Water Heat Pump
• Do not store or use flammable gas or combustibles near the unit.
- There is risk of fire or failure of unit.
• Do not use the unit in a tightly closed space for a long time.
- It may cause damage to the unit.
• When flammable gas leaks, turn off the gas and open a window for
ventilation before turning the unit on.
- There is risk of explosion or fire.
• If strange sounds, or small or smoke comes from unit, turn the
breaker off or disconnect the power supply cable.
- There is risk of electric shock or fire.
• Stop operation and close the window in storm or hurricane. If
possible, remove the unit from the window before the hurricane
arrives.
- There is risk of property damage, failure of unit, or electric shock.
• Do not open the front cover of the unit while operation. (Do not touch
the electrostatic filter, if the unit is so equipped.)
- There is risk of physical injury, electric shock, or unit failure.
• Do not touch any electric part with wet hands. you should be power
off before touching electric part.
- There is risk of electric shock or fire.
• Do not touch refrigerant pipe and water pipe or any internal parts
while the unit is operating or immediately after operation.
- There is risk of burns or frostbite, personal injury.
• If you touch the pipe or internal parts, you should be wear protection
or wait time to return to normal temperature.
- Otherwise , it may cause burns or frostbite, personal injury.
• Turn the main power on 6 hours ago before the product starting
operation.
- Otherwise, it may cause compressor damage.
• Do not touch electric parts for 10 minutes after main power off.
- There is risk of physical injury, electric shock.
• The inside heater of product may operate during stop mode. It is
intended to protect the product.
• Be careful that some part of the control box are hot.
- There is risk of physical injury or burns.
• When the unit is soaked (flooded or submerged), contact an
Authorized Service Center.
- There is risk of fire or electric shock.
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 4

Safety Precautions
Installation Manual 5
ENGLISH
• Be cautious that water could not be poured to the unit directly.
- There is risk of fire, electric shock, or unit damage.
• Ventilate the unit from time to time when operating it together with a
stove, etc.
- There is risk of fire or electric shock.
• Turn the main power off when cleaning or maintaining the unit.
- There is risk of electric shock.
• Take care to ensure that nobody could step on or fall onto the unit.
- This could result in personal injury and unit damage.
• For installation, always contact the dealer or an Authorized Service
Center.
- There is risk of fire, electric shock, explosion, or injury.
• If the unit is not used for long time, we strongly recommend not to
switch off the power supply to the unit.
- There is risk of water freezing.
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 5

Safety Precautions
6Air-to-Water Heat Pump
Installation
• Always check for gas (refrigerant) leakage after installation or repair
of unit.
- Low refrigerant levels may cause failure of unit.
• Keep level even when installing the unit.
- To avoid vibration or water leakage.
• Use two or more people to lift and transport the unit.
• Avoid personal injury.
Operation
• Do not use the unit for special purposes, such as preserving foods,
works of art, etc.
- There is risk of damage or loss of property.
• Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.
- There is risk of fire, electric shock, or damage to the plastic parts of
the unit.
• Do not step on or put anything on the unit.
- There is risk of personal injury and failure of unit.
• Use a firm stool or ladder when cleaning or maintaining the unit.
- Be careful and avoid personal injury.
• Do not turn on the breaker or power under condition that front panel,
cabinet, top cover, control box cover are removed or opened.
- Otherwise, it may cause fire, electric shock, explosion or death.
CAUTION
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 6

General Information
Installation Manual 7
ENGLISH
According to IEC 660335-1
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not
play with the appliance.
According to EN 660335-1
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understnd the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
2. General Information
Model Information
With advanced inverter technology, is suitable for applications like under floor heating,
under floor cooling, and hot water generation. By Interfacing to various accessories user can cus-
tomize the range of the application.
In this chapter, general information of is presented to identify the installation procedure.
Before beginning installation, read this chapter carefully and find helpful information on installation.
Model number nomenclature
Global Model Name
Function
A : General heating heat pump
H : Domestic Hot heating only
T : High temperature heating heat pump
Product electric power rating
6 : 220-240V, 1Ø, 50Hz
8 : 380-415V, 3Ø, 50Hz
Serial Number
Heating capacity (kW)
Ex) 16 : 16kW class
Model Type
W: DC Inverter Heat Pump
H: Heat Pump
Classification
N: Indoor Unit
U: Outdoor Unit
B: Monobloc
Air-to-Water Heat Pump for R410A
AH B W 16 6 A 0
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 7

General Information
8Air-to-Water Heat Pump
Europe Model Name
M : AWHP Monobloc
H: Air to Water Heat Pump
1 : 220-240V, 1Ø, 50Hz
3 : 380-415V, 3Ø, 50Hz
HM161M
Leaving Water Combination
None: Low Temperature Leaving Water
H : High Temperature Leaving Water
M : Middle Temperature Leaving Water
Nominal Heating Capacity Indication
Conversion to kW
Ex) “09” : 10 kW
“12” : 12 kW
“14” : 14 kW
Airborne Noise Emission
The A-weighted sound pressure emitted by this product is below 70 dB.
** The noise level can vary depending on the site.
The figures quoted are emission level and are not necessarily safe working levels.
Whilst there is a correlation between the emission and exposure levels, this cannot be used reliably
to determine whether or not further precautions are required.
Factor that influence the actual level of exposure of the workforce include the characteristics of the
work room and the other sources of noise, i.e. the number of equipment and other adjacent process-
es and the length of time for which an operator exposed to the noise. Also, the permissible exposure
level can vary from country to country.
This information, however, will enable the user of the equipment to make a better evaluation of the
hazard and risk.
Limiting concentration
Limiting concentration is the limit of Freon gas concentration where immediate measures can be
taken without hurting human body when refrigerant leaks in the air. The limiting concentration shall
be described in the unit of kg/m3(Freon gas weight per unit air volume) for facilitating calculation.
nCalculate refrigerant concentration
Total amount of replenished refrigerant
in refrigerant facility (kg)
Capacity of smallest room where
indoor unit is installed (m3)
Refrigerant
concentration
(kg/m3)
=
Limiting concentration: 0.44kg/m3(R410A)
- Additional Information : serial number is refer to the barcode on the product.
- Max allowable pressure High side :
4.2 Mpa / Low side : 2.4 Mpa
- Refrigerant : R410A
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 8

General Information
Installation Manual 9
ENGLISH
Be very careful while carrying the unit.
- Do not have only one person carry the unit if it is more than 20 kg (44.1 lbs).
- PP bands are used to pack some products. Do not use them as a mean for transportation because
they are dangerous.
- Tear plastic packaging bag and scrap it so that children cannot play with it. Otherwise plastic pack-
aging bag may suffocate children to death.
- When carrying the unit, be sure to support it at 4-points. Carrying and lifting the unit with 3-point
support may make it unstable, resulting in a fall.
CAUTION
General considerations
• If a sunroof is built over the unit to prevent
direct sunlight or rain exposure, make sure that
heat radiation from the heat exchanger is not
restricted.
• Ensure that the spaces indicated by arrows
around front, back and side of the unit.
• Do not place animals and plants in the path of
the warm air.
• Take the weight of the unit into account and
select a place where noise and vibration are
minimum.
• Select a place so that the warm air and noise
from the unit do not disturb neighbors.
• The surface of the ground or the structure must
be strong enough to bear the weight of the unit.
Installation Conditions
More than
300mm
Fence or
obstacles
More than 700mm
More than 600mm
*Minimum*Minimum
300mm300mm
Sunroof
*Minimum
300mm
* : Please secure the space to install the shut-off
valve and strainer.
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 9

Installation at Seaside
Selecting the location
1) If the unit is to be installed close to the seaside, direct exposure to the sea wind should be avoided.
Install the unit on the opposite side of the sea wind direction.
- It should be strong enough like concrete to pre-
vent the sea wind from the sea.
- The height and width should be more than 150%
of the unit.
- It should be keep more than 700 mm of space
between unit and the windbreak for easy air flow.
2) In case, to install the unit on the seaside, set up a windbreak not to be exposed to the sea wind.
3) Select a well-drained place.
1. Unit should not be installed in areas where corrosive gases, such as acid or alkaline gas, are
produced.
2. Do not install the unit where it could be exposed to sea wind (salty wind) directly. It can result
corrosion on the unit. Corrosion, particularly on the condenser and evaporator fins, could
cause unit malfunc-tion or inefficient performance.
3. If unit is installed close to the seaside, it should avoid direct exposure to the sea wind.
Otherwise itneeds additional anticorrosion treatment on the heat exchanger.
CAUTION
Sea wind Sea wind
Sea wind
Windbreak
1. If you can’t meet above guide line in the seaside installation, please contact your supplier for
the additional anticorrosion treatment.
2. Periodic ( more than once/year ) cleaning of the dust or salt particles stuck on the heat
exchanger by using water
General Information
10 Air-to-Water Heat Pump
1,MFL68026605,영영 2017. 8. 1. 영영 11:48 Page 10