LG RT/MT/MZ-42PZ90/H/B/R/S User manual

PLASMA MONITOR/TUNER
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS : RF-03FA
MODEL : RT/MT/MZ-42PZ90/H/B/R/S
MODEL : RT/MT-42PZ92/H/B/R/S
MODEL : RT/MT/MZ-42PZ91M/91V/B/R/S
MODEL : RT/MT-42PZ93M/93V/B/R/S
MODEL : RT/RZ-BA50
website:http://biz.LGservice.com
e-mail:http://www.LGEservice.com/techsup.html
Aug., 2003
Printed in KoreaP/NO : 3828VD0129S

- 2 -
CONTENTS
SAFETY PRECAUTIONS ...................................................................................3
DESCRIPTION OF CONTROLS ........................................................................ 4
SPECIFICATIONS .............................................................................................. 8
ADJUSTMENT INSTRUCTIONS ......................................................................17
BLOCK DIAGRAM.............................................................................................19
ASSEMBLY METHOD........................................................................................20
PRINTED CIRCUIT BOARD ..............................................................................25
EXPLODED VIEW..............................................................................................30
EXPLODED VIEW PARTS LIST........................................................................31
REPLACEMENT PARTS LIST...........................................................................33
SCHEMATIC DIAGRAM ........................................................................................

- 3 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitry that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the specified.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each exposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits specified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF

- 4 -
DESCRIPTION OF CONTROLS
<Back Panel>
<Front Panel Controls>
Connection to PC
Note: The connection cables shown above to the right are not included with the Monitor.
A D-sub 15-pin cable and a DVI cable are provided to connect the Monitor to a PC.
Connection to AV equipment
( )( )
R
( )( )
L
REMOTE
CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
EXTERNAL SPEAKER
YP B P R
(MONO)
R
AUDIO
L
R
AUDIO
L
S-VIDEO AC INPUTAUDIO INPUT AUDIO INPUT COMPONENT INPUT AUDIO INPUT RGB OUTPUTRGB INPUTDVI INPUT
VIDEO
INPUT
EXPANDED
INPUT
VOL.MENU
INPUT
SELECT
ON/OFF
Main Power Button INPUT SELECT Button
VOLUME (F,G) Buttons
Power Standby Indicator
Illuminates red in standby mode,
Illuminates green when the
Monitor is turned on
Remote Control Sensor
MENU Button
D,EButtons
AUDIO
INPUT
VIDEO
INPUT
S-VIDEO
INPUT
AUDIO
INPUT
RS-232C
INPUT
DVI INPUT
RGB INPUT RGB
OUTPUT
EXPANDED
INPUT
AUDIO
INPUT
COMPO-
NENT INPUT
- Shown is a simplified representation of the Monitor.
- Here shown may be somewhat different from your set.

- 5 -
<Back Panel>
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
AV1(EXPANDED)
EXPANDED OUTPUT
ANT INDC IN
(DC 12V) +75 Ω
REMOTE
CONTROL
AV2(EXPANDED)
( )
( )
R
( )
( )
L
RS-232C INPUT
(CONTROL/SERVICE)
EXPANDED
INPUT
EXTERNAL SPEAKER
AC INPUT AUDIO INPUT RGB OUTPUTRGB INPUTDVI INPUT
( )( )
R
( )( )
L
REMOTE
CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
EXPANDED
INPUT
EXTERNAL SPEAKER
Y P B P R
(MONO)
R
AUDIO
L
R
AUDIO
L
S-VIDEO AC INPUTAUDIO INPUT AUDIO INPUT COMPONENT INPUT AUDIO INPUT RGB OUTPUTRGB INPUTDVI INPUT
VIDEO
INPUT
RCA Type
Scart Type
ANTENA INPUT
AV(EXPAND
ED) INPUT
RT-BA50
RZ-BA50
AV1/2 (EXPAND-
ED) INPUT
EXTERNAL
SPEAKER (8
ohm output) RS-232C INPUT
(CONTROL/SE
RVICE) PORT
EXPANDED INPUT POWER CORD
SOCKET
DVI INPUT/RGB
INPUT/AUDIO INPUT /
RGB OUTPUT
AUDIO INPUT/COMPONENT INPUT /
REMOTE CONTROL / S-VIDEO/VIDEO
INPUT/AUDIO INPUT
EURO SCART SOCKET
DC IN
(DC 12V) AV OUT- PUT REMOTE CONTROL
EXPANDED
OUTPUT

- 6 -
-Connect the Plasma Display with various external equipments after connecting the Monitor with the PDP
Tuner and the Speakers.
1. Connect the RF out socket of the VCR to the aerial socket on the
back of the monitor.
2. Connect the aerial cable to the RF aerial in socket of the VCR.
3. Store the VCR channel on the programme number 0 using the
‘Manual programme tuning’ section.
4. Select the programme number where the VCR channel is stored.
5. Press the PLAY button on the VCR.
Antenna Connection
1. Turn the monitor off and disconnect the mains plug.
2. Carefully place the Monitor screen side down on a cushioned surface that will protect the monitor screen from
damage.
3. Mount the PDP Tuner gently into the correct position. Make sure it is inserted correctly.
4. Tighten the screws.
5. Connent the EXPANDED OUTPUT socket the on the PDP Tuner to the EXPANDED INPUT socket on the
Monitor.
6. Turn the monitor on.
Installing PDP Tuner on the Monitor
-This function works only when the PDP Tuner is installed on the LG plasma display monitor.
Monitor Out Setup
The PDP Tuner has a special signal output capability which allows you to hook up a second TV or monitor.
Just connect the second TV or monitor to the AV OUTPUT socket on the PDP Tuner. See the Operating Manual
of the second TV or monitor for further details regarding that device’s input settings.
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
ANT OUT
ANT IN
AV1(EXPANDED)
EXPANDED OUTPUT
ANT INDC IN
(DC 12V) +75 Ω
REMOTE
CONTROL
AV2(EXPANDED)
< Back panel of the PDP Tuner >or
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
ANT OUT
ANT IN
< Back panel of the PDP Tuner >
VCR
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
< Back panel of the PDP Tuner >
RZ-BA50
Input Mode
Main
Picture
Sub
Picture
Monitor OUT
(AV2(EXP.))
Normal
PIP/DW
TV, AV, AV1(EXP.)
or S-Video Main Picture
RGB, DVI or
Component
TV or AV1(EXP.)
Main
Picture
TV, AV,
AV1(EXP.) or
S-Video
Sub Picture
Main Picture
RT-BA50
Input Mode
Main
Picture
Sub
Picture
Monitor OUT
(AV(EXP.))
Normal
PIP/DW
TV, AV(EXP.), AV or S-
Video Main Picture
RGB, DVI or
Component
TV, AV(EXP.)
Main
Picture TV, AV(EXP.), AV or S-Video
Sub Picture
Main Picture

- 7 -
Watching Cable TV
-After subscribing for a local cable TV station and installing a converter you can watch cable TV.
- For further information of cable TV, contact the local cable TV station.
Watching VCR
-When connecting the Monitor to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white,
Audio (R) -red).
- Connect the VIDEO INPUT socket (yellow) with the BNC-RCA adaptor to the VIDEO INPUT on the Monitor.
- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the Monitor.
- If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR
to the Video input.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of the monitor.
- Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still pic-
ture from a VCR.
If a 4:3 picture format is used; the fixed image may remain visible on the screen.
- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor.
Watching TV programmes
- Turn the Plasma Display on and select the programme you
want.
Watching VCR
1. Use the INPUT SELECT button on the remote control to select
AV ( AV1 or AV2 ) or AV(EXP.) ( AV1(EXP.) or AV2(EXP.) ).
-If both S-VIDEO and VIDEO sockets have been connected to
the S-VHS VCR simultaneously, only the S-VIDEO can be
received.
-If connected to S-VIDEO, select the S-Video external input
source.
2. Insert a video tape into the VCR and press the PLAY button on
the VCR. (See VCR owner’s manual)
In using connection 1
1. Select programme number in programme switch of
cable box.
2. Match the Plasma Display programme with selected
programme of cable box.
3. Select your desired programme with the remote
control for cable box.
In using connection 2
1. Use the INPUT SELECT button on the remote con-
trol and select
AV ( AV1 or AV2 ) or AV(EXP.)
( AV1(EXP.) or AV2(EXP.) ).
2. Tune to cable service provided channels using the
cable box.
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
S-VIDEO OUT
IN
(R) AUDIO (L) VIDEO
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
Cable
TV
(R) AUDIO (L) VIDEO
VCR RF Cable
TV
(R) AUDIO (L) VIDEO
VCR RF
< VCR >
< Back panel of
the PDP Tuner >
< Back panel of the PDP Tuner >
For cable TV
< Cable Box >
12

- 8 -
Watching external AV source
-When connecting the monitor to an external source, match the colours of
AUDIO/VIDEO input jacks on the monitor with the output jacks on the
audio/video equipment: Video = yellow, Audio (Left) = white, Audio
(Right) = red.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of
the monitor.
How to use
1. Use the INPUT SELECT button on the remote control to select AV
( AV1 or AV2 ) or AV(EXP.) ( AV1(EXP.) or AV2(EXP.) ).
2. Operate the corresponding external equipment. See external equip-
ment operating guide.
Watching DVD
Watching DTV (option)
- To watch digitally broadcast programs, purchase and connect a dig-
ital set-top box.
How to connect
Connect DVD video inputs to Y, PB, PRof COMPONENT INPUT
and audio inputs to Audio sockets of AUDIO INPUT.
Or, connect the Euro scart socket of the VCR to the Euro scart
socket of the set.
How to use
1. Turn on the DVD player, and insert a DVD.
2. Use INPUT SELECT button on the remote control to select
Component or ( AV1 or AV2 ) or ( AV1(EXP.) or AV2(EXP.) ).
Refer to the DVD player's manual for operating instructions.
How to connect
1. Use the monitor’s COMPONENT (Y, PB, PR) INPUT, RGB or DVI
jack for video connections, depending on your set-top box con-
nector. Then, make the corresponding audio connections.
How to use
1. Turn on the digital set-top box. (Refer to the owner’s manual for
the digital set-top box.)
2. Use INPUT SELECT on the remote control to select Component ,
RGB or DVI .
•Component Input ports
You can get better picture quality if you connect DVD
player with component input ports as below.
Component ports of the
Monitor YPBPR
Video output ports
of DVD player
Y
Y
Y
Y
Pb
B-Y
Cb
PB
Pr
R-Y
Cr
PR
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
R L
AUDIO VIDEO
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
REMOTE
CONTROL
EXPANDED
INPUT
Y P B P R
(MONO)
R
AUDIO
L
R
AUDIO
L
S-VIDEO AC INPUTAUDIO INPUT AUDIO INPUT COMPONENT INPUT RGB OUTPUT
BR
(R) AUDIO (L) (R) AUDIO (L)
S-VIDEO
VIDEO
INPUT
< Back panel of a DVD player >
or
< Back panel of the PDP Tuner >
< Back of the external equipment >
Camcorder
Video game set
< Back panel of the PDP Tuner >
< Back panel of
the Monitor >
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
(R) AUDIO (L) Y P
B R
P(R) AUDIO (L) DTV OUTPUT
REMOTE
CONTROL
EXPANDED
INPUT
Y P B P R
(MO
R
AUDIO
L
R
AUDIO
L
S-VIDEO AUDIO INPUT AUDIO INPUT COMPONENT INPUT AUDIO INPUT RGB OUTPUTRGB INPUTVI INPUT
VIDEO
INPUT
< Digital Set-top box >
or
< Back panel of the PDP Tuner >
< Back panel of
the Monitor >
•DTV Input signal
576p(50Hz)
1080i(50Hz)
1152i(50Hz)
Mode Terminal Component
o
o
o
RGB (DTV)
o
o
o

- 9 -
Connecting PC
- To enjoy vivid picture and sound, connect a PC to the Monitor.
- Avoid keeping a fixed image on the monitor’s screen for a long period of time. The fixed image may become permanently imprint-
ed on the screen; use a screen saver when possible.
-Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the Monitor; change the resolution out-
put of PC accordingly.
-There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC
mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the
picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the
manufacturer of the PC graphic card.
- The synchronization input form for Horizontal and Vertical frequencies is separate.
Setup Instructions to Connect a PC to your Monitor
- We recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.
In RT/RZ-50PZ44/45/46/47/90/91/92/93 series, we recommend using 1024x768, 60Hz for the PC mode, they provide the best pic-
ture quality.
- If the resolution of PC is over UXGA, there will be no picture on the Monitor.
-Connect the signal cable from the monitor output port of the PC to the RGB INPUT(PC INPUT) port of the Monitor or the signal
cable from the DVI output port of the PC to the DVI INPUT(DIGITAL RGB INPUT) port on the Monitor.
- Connect the audio cable from the PC to the Audio input on the Monitor. (Audio cables are not included with the Monitor).
- If using a sound card, adjust PC sound as required.
-This monitor apply a VESA Plug and Play Solution. The monitor provides EDID data to the PC system with a DDC protocol. The
PC adjusts automatically to use this monitor.
- DDC protocol is preset for RGB (Analog RGB), DVI (DVI, Digital RGB) mode.
- If required, adjust the monitor settings for Plug and Play functionally.
-If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT (PC
INPUT) or DVI INPUT (DIGITAL RGB INPUT) to display the PC on the monitor.
If graphic card on the PC does output analog and digital RGB simultaneously, set the monitor to either RGB or DVI; (the other
mode is set to Plug and Play automatically by the monitor.)
-DOS mode may not work depending on video card if using a DVI-I cable.
- To see a normal picture, match the VGA mode and DVI signal (640x480, 848x480, 852x480, 1360x768 or 1366x768).
(MONO)
R
AUDIO VIDEO
L
AV(EXPANDED) INPUT
R
AUDIO VIDEO
L
AV OUTPUT
EXPANDED OUTPUT
REMOTE
CONTROL
ANT INDC IN
(DC 12V) +75 Ω
( )( )
R
( )( )
L
RS-232C INPUT
(CONTROL/SERVICE)
EXPANDED
INPUT
EXTERNAL SPEAKER
AU AUDIO INPUT RGB OUTPUTRGB INPUTDVI INPUT
< Back panel of the PDP Tuner >
< Back panel of the Monitor >
PC Setup
1. Turn on the PC and apply power to the Monitor.
2. Turn on the display by pressing the POWER button on the
Monitor’s remote control.
3. Use the INPUT SELECT button on the remote control to select the
RGB or DVI input source.
4. Set the resolution output of the PC to SXGAor under (1280 x 1024,
60Hz).

- 10 -
-When using the remote control aim it at the remote control sensor of the Monitor.
- There's maybe a defect in consecutive operation of remote control in specified brightness according to this monitor
feature.
•Open the battery compartment cover on the back side and
insert the batteries with correct polarity.
• Install two 1.5V alkaline batteries of AAA type. Don’t mix used
batteries with new batteries.
Installing Batteries
1 2 3
4 5 6
7 8
0PSM SSM
SIZE REVEAL UPDATE
MIX HOLD
INDEX MODE
TIME
9
POWER
MULTIMEDIA INPUT SELECT
ARC I/II/
PIP/DW
TEXT/
PR-/
PR+/
SWAP
MENU PR
PR
MUTE
OK
VOL
WIN.POSITION
SPLIT ZOOM ZOOM-
WIN.SIZE
ZOOM+
SLEEP
LIST
STOP
PLAY FF
REC
REW
P/STILL
VOL
PIP INPUT
?
M
POWER
Switches the Monitor on from stand-
by or off to standby.
MULTIMEDIA
ARC
Changes the picture format.
PIP/DW
Switches the sub picture on or off
PR + /
*
or PR - /
*
Selects a program for the sub picture.
SWAP
Alternates between main and sub pic-
ture.
PIP INPUT
Selects the input mode for the sub
picture.
WIN.SIZE
Adjusts the sub picture size.
WIN.POSITION
Moves the sub picture to DD/ EEor FF/ GG
direction.
SWAP
Returns to the previously viewed
programme.
NUMBER buttons
MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.
SPLIT ZOOM
Enlarge the screen with regular
ration.
VCR BUTTONS
Controls a LG video cassette
recorder.
OK
DD/ EE
Selects a menu option.
FF/ GG(Volume button)
Increases/decreases sound level.
Adjusts menu settings.
INPUT SELECT
I/II/*
Selects the language during dual lan-
guage broadcast.
Selects the sound output.
TEXT/*
These buttons are used for teletext.
SSM
To select the sound appropriate to
your viewing program character :
Flat , Speech , Movie , Music , or User
LIST
Displays the program table.
SLEEP
Sets the sleep timer.
ZOOM+ / ZOOM-
Enlarges or reduces the main picture
size.
MUTE
Switches the sound on or off.
PSM
Adjusts the factory preset picture
according to the room.

- 11 -
D-sub 15 pin cable
AS mark
LG TV
Owner’s Manual
1.5V
1.5V
Alkaline batteries BNC-RCA adaptor
(optional)
Power Cord
1 2 3
4 5 6
7 8
0PSM SSM
SIZE REVEAL UPDATE
MIX HOLD
INDEX MODE
TIME
9
POWER
MULTIMEDIA INPUTSELECT
ARC I/II/
PIP/DW
TEXT/
PR-/
PR+/
SWAP
MENU PR
PR
MUTE
OK
VOL
WIN.POSITION
SPLITZOOM ZOOM-
WIN.SIZE
ZOOM+
SLEEP
LIST
STOP
PLAY FF
REC
REW
P/STILL
VOL
PIPINPUT
?
M
Remote Control handset
DVI-D Cable
Accessories
-Optional extras can be changed or modified for quality improvement without any notification new optional extras can be
added.
- Contract your dealer for buying these items.
Optional Extras
Phone scart cable (Optional)
Tilt wall mounting bracket
Video cables Audio cables
Desktop stand
Wall mounting bracket Ceiling mounting bracket
Speakers
Desktop Speaker stand
Vertical Wall mounting bracket

- 12 -
SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement .
VScope
This specification can be applied to all model of 42”PDP
MONITOR related to RF-03FA Chassis.
V Test Condition
1) Temperature : 25¡5°C
2) Relative Humidity: 65¡10%
3) Power Voltage:Standard Input Voltage
(AC 110V-240V~, 50/60Hz)
But Standard input voltage mark value is marked by model.
4) Follow each drawing or spec for spec and performance of
parts,based upon P/N of RPL
5)
Warm up set for more than 20min before the measurement.
VTest and Inspection Method
1) Performance:Follow the Standard of LG TV test
2) Extra standards
Safety: Follow the standard of CE, IEC
EMC : Follow the standard of CE, IEC
Remark
Safety: IEC60065,IEC60095
EMI : EN55013
-Conducted / Radiation
EMI : EN55013 (Antenna Terminal Voltage)
EMS : EN55024
Safety : IEC60065,IEC60095
EMI : EN55013
-Conducted / Radiation
EMI : EN55013 (Antenna Terminal Voltage)
Model Name
MZ-42PZ44
MZ-42PZ45V
RZ-BA50
MT-42PZ44
MT-42PZ45V
MT-42PZ46
RT-BA50
Market
EU
N-EU
Chassis
RF-03FA
(Monitor)
RF-03FA
(PDP Tuner)
AV BOARD
Brand
LG
LG
LG
LG
LG
LG
Model Name
MZ-42PZ44/45V
MZ-42PZ90/91V
MT-42PZ44/45V/46/47V
MT-42PZ90/91V/92/93V
RZ-BA50
RT-BA50
AP-42EA42
AP-42EA43
Market Place
EU
N-EU
EU
N-EU
EU, Scart Type AV BOARD
N-EU, RCA Type AV BOARD

EU
VGA, SVGA, XGA, SXGA 60Hz
Digital RGB Input
PAL, SECAM, NTSC
PAL, SECAM, NTSC
480i, 480p, 576i, 576p
L/R 2 group
Discrete IR
VGeneral Specification
1
2
3
4
5
6
7
42inch wide Colour Desplay Module
16 : 9
PDP42V5####, Fish Bone
45% Total light ransmittance
1) Temp. : 0 ~ 40 °C
2)Humidity : below 85%
1) Temp. : -20 ~ 60 °C
2)Humidity : below 85%
110 ~240V~, 50/60Hz
No Item Specification Remark
Display Screen Device
Aspect Ratio
PDP Module
Screen Filter
Operating Environment
Storage Environment
Input Voltage
PDP
LGE
Maker : NBK (E-Mesh)
LGE Mark SPEC
MZ-42PZ44/45
MURADA
SONY
SANKEN
- 13 -
VModel Specification
(1) MZ-42PZ4x (MZ-42PZ44/45)
No Item Specification Remark
(2) RZ-BA50
EU
DC 12V
PAL B/ G/ I/ D/ K, SECAM L/ L”
Upper Heterodyne
PAL, SECAM
No Item Specification Remark
Market
Input Voltage
Broadcasting system
Receiving system
Scart Jack
16
17
18
19
20
8
9
10
11
12
13
14
15
Market
RGB Input
DVI Input
Video Input System
S-Video Input
Component Input
Audio Input
Wired Control

- 14 -
(3) MT-42PZ4x (MT-42PZ44/45V/46)
N-EU
VGA, SVGA, XGA, SXGA 60Hz
Digital RGB Input
PAL, SECAM, NTSC
PAL, SECAM, NTSC
480i, 480p, 576i, 576p, 1080i, 1152i
L/R 2 group
Discrete IR
No Item Specification Remark
Market
RGB Input
DVI Input
Video Input System
S-Video Input
Component Input
Audio Input
Wired Control
21
22
23
24
25
26
27
28
(2) RT-BA50
N-EU
12V
PAL B/ G/ I/ D/ K, NTSC
Upper Heterodyne
PAL, SECAM, NTSC
No Item Specification Remark
Market
Input Voltage
Broadcasting system
Receiving system
Video In/ Out System
29
30
31
32
33
1
2
3
4
5
Remote controller code
Remote control
Local Key
Set up method
RGB input
- D - Sub 15 pin
NEC Code
1) Wireless Remote Control
2) Wired Remote Control
-RCA AV B’D
-Tuner Box
Menu, Input select V, VOLF, VOLG
UpD/ DownE, Power (Main Power)
Wall Mount/ Desk top
Pivot (Optional)
RGB PC Input
- VGA ~ 85Hz
- SVGA ~ 85Hz
- XGA ~ 75Hz
- SXGA ~ 60Hz
RGB - DTV Input
-480p/ 60Hz
-576p/ 50Hz
-1080i/ 50Hz
-1152i/ 50Hz
DVI - D (Digital RGB)
Pivot model
MT-42PZ4x
Featur
e
(MNT)
VFeature and Function
No Item Specification Remark
1
1

- 15 -
5
6
7
8
9
RGB out
- D - Sub 15pin
Audio input
- Phone Jack
RS-232C
- D - Sub pin
External Speak output
Expanded Control
Component input
(Y/ PB/ PR, Y/Cb/Cr)
Video Input(CVBS)
Audio Input
IR Jack
ANT In (RF)
- Tuner
AV In/ Out
-Scart Jack
IR Jack
DC Jack
Expanded Control
ANT In (RF)
AV In/ Out (CVBS)
-RCA Jack
IR Jack
DC Jack
Expanded Control
Scar Jack
S- Video Input
Audio Input
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
2
1
1
1
2
1
1
RGBHV
L/ R For RGB Input
115200bps
L/ R
Tuner Box Control
480i/ 480p/ 576i/ 576p
480i/ 480p/ 576i/
480i/ 480p/ 576i/ 576p/ 1080i/
1152i
PAL, SECAM, NTSC
L/ R For Video/ S- Video
L/ R For Component
Discrete IR
PAL- BG/ DK/ I,
SECAM-L/L’
Scart 1 (TV Out)
Scart 2 (MNT Out)
Wired Remote Control
DC 12V In
36Pin
PAL-BG/ DK/ I, NTSC
PAL, SECAM, NTSC Input
AV Output
Wired Remote Control
DC 12V In
36Pin
Vin, FB, RGB in, L/R in
1) TV out non-opposition
2) Auto AV non-function
Vin, Lin, R in, V out, L out, R out
1) MNT out of Tuner Box
non-opposition
2) Auto AV non-opposition
PAL, SECAM, NTSC
L/R For S-Video
SPK Output
36Pin
MZ-42PZ4x
MT-42PZ4x
Australia
RZ-BA50
- Follow Scart In/ Out Spec
- Auto AV (Scart 2 priority)
RT-BA50
Feature
(MNT)
RCA
Type
AVB’D
Scart
Type
Tuner
model
RCA
Type
Tuner
model
Scart
Type
AV B’D
No Item Specification Remark

- 16 -
10
11
12
13
Picture Status Mode
Color Status Mode
Color Temperature
User
Sound Status Mode
AVL(Auto Volume
limit)
User
Clock
Off Time
On Time
Auto Sleep
Language (For OSD)
Child Lock
- Local key Lock
ISM Method
SET ID
(RS- 232C control ID)
Low Power
PSM
GDynamic, Standard, Mild, User
CSM
GNormal (9,500 °K)
GCool (12,000 °K)
GWarm (8,500 °K)
G User (RGB Control)
GR, G, B
GContrast, Brightness, Colour,
Sharpness
GTint
SSM
GFlat, Speech, Movie, Music, User
On
Off
GTreble, Bass, Balance
User Setting
Off
On : User Setting (Time)
Off
On : User Setting (Time/ Volume)
Off
On
EU 5 languages
GEnglish, French, German,
Spanish, Italian
3 languages
GEnglish, Chinese, Russian
On
Off
GNormal : ISM action On
GOrbiter : 2 min/ 2pixel a cycle
GInversion : 30 min cycle On/ Off
GWhite Wash : Any key Off
1 ~ 99
On : 30% .
Off
4 - Mode
- Default : Standard
4 - Mode
- Default : Normal
Each +/- 10 Step
- Default : 0
Default
Enable For NTSC
5 - Mode
- Default : Flat
- Default : OFF
Default : 12:00
Default : 12:00
Default : 12:00/ Vol. 30
Default : Off
Default : English
- etc. PR standard
Austailia/ China/ russia
Default : Off
--> Module Spec
Default : 1
Default : Off
MENU
(picture)
MENU
(Sound)
MENU
(Time)
MENU
(special)
No Item Specification Remark

- 17 -
14
15
OSD Rotate
(Optional)
Auto Configure
ARC
Zoom In/ Out
Position
Manual
Screen Adj.
Reset
VGA Mode
YNR
MT-42PZ46
1)MZ-42PZ4x
2)RZ-BA50
MZ-42PZ4x
1)MT-42PZ4x
2)TE-BA50
MT-42PZ4x
GNormal
GRotate : OSD Rotate
RGB PC
Auto : RF/ AV/ S-AV/ Component-i
4:3 : All
16:9 : All
14:9 : RF/ AV/ S-AV/ Component-i
ZOOM : RF/ AV/ S-AV/ Component-i
Zoom in/ Out (100%~ 300%)
-RGB Input
-Component Input
(480p/ 576p / 1152is)
Phase : 0~ 31
Colork : -50~ +50
TV / VCR
O
640 x 480
848 x 480
852 x 480
On
Off
RGB
$ DBI
TV$AV1(EXP)$AV2(EXP)$AV$
S-VIDEO$COMPONENT$RGB $
DVI
RGB$DVI$AV1$AV2$S-VIDEO
TV$AV(EXP)$AV$S-VIDEO
$COMPONENT$RGB$DVI
RGB$DVI$COMPONENT$AV
$S-VIDEO
TV$AV1(EXO)$AV2(EXP)$RG
B$DVI
TV$VIDEO(EXP)$RGB$DVI
TV$AV1(EXP)$AV2(EXP)$AV1
$AV2$S-VIDEO$RGB$DVI
Default : Normal
Enable For Pivot
Disable For
DW Mode
Default :100
RGB mode only
RF, AV, S- Video
To Initialize for user data
WVGA correspondence
RGB/ DVI Mode
Luminance Noise
Reduction
- Nothing AV B’D
- Nothing Tuner Box
- RCA AV B’D
- Scart Tuner Box
- Scart AV B’D
- RCA AV B’D
- RCA Tuner Box
- RCA AV B’D
- Nothing AV B’D
- Scart tuner Box
- Nothing AV B’D
- RCA Tuner Box
MENU
(Screen)
MENU
(PIP/DW)
No Item Specification Remark
Input
(Main)

- 18 -
15
16
17
Input
(Main)
DW
PIP
Sub Input
Win, Size
Win, Position
PIP ARC
Auto Program
Manual Program
Program Edit
Input Select Multimedia
Input
Select
PIP/ DW
SWAP
I/ II/ *
Relation Key except TEXT
SPLIT ZOOM
ZOOM-, ZOOM+
Power On
Etc.
TV$AV1(EXP)$AV2(EXP)$AV1
$AV2$S-VIDEO$RGB$DVI
TV$AV(EXP)$AV1$AV2$
S-VIEDO$RGB$DVI
OFF, DW1, DW2
OFF, ON
Variable
Variable
4:3, 16:9
System, Storage(0~99), Start
Storage(0~99), System, CH., Fine,
Search, Name
Del, Copy, Move, Skip
Component$RGB$DVI
Sequentially For Input Mode
PIP$DW1$DW2$Off
O (Main/Sub screen Swap)
SiF Control
O (TEXT action standard)
2/ 4/ 9 division
100% ~ 300%
Power, Numberic(0~9), TV/ AV,
Multimedia, PR +/-
Numberic(0~9), ARC, PR+/-,
VOL+/-, MUTE, PIP Input, PIP
PR+/-, MENU, PSM, SSM
Main Input
RGB, DVI
Component 480 -
TV, AV, S-VIDEO
SCART
Component 480i
- Scart AV B’D
- Scart Tuner Box
- Scart V B’D
- RCA Tuner Box
Main/Sub screen All
PIP Screen Only
- With Tuner Box
- Gray Except TV Mode
- Gray For MNT
Main Input sequence
For Tuner Boxs
Available Sub Input
TV, AV, S-VIDEO, SCART, Component 480i
All (Except Limitation)
MENU
(PIP/DW)
MENU
(CH)
Hot Key
(Remote)
No Item Specification Remark
Equal Main Input
* Display Condition
1) Identity of Input Source is not Main/ Sub Display
2) Don’t allow PIP/DW between graphic signals of 480p -
3) When this condition appear,swap the Main/Sub screen and old
input sourse.

4H Comb
O
X (Option)
O
O
Adaptive Comb Filter
DCDI
Film Mode
Motion Detection
Noise Reduction
- 19 -
Item Specification Remark
18 VPC3230
FLI2300/ FLI231
0
V Component Video Input (Y, PB, PR)
1
2
3
4
5
6
720 x 480
720 x 480
720 x 576
720 x 576
1920 x 1080
1920 x 1080 (+72)
15.625
31.250
15.625
31.250
28.125
31.250
60.00
60.00
50.00
50.00
50.00
50.00
13.500
27.027
13.500
27.027
74.250
74.250
480I
480P
576I
576p
1080i
1152i
No
No Resolution H-freq (kHz) V-freq (Hz) Pixel clock (MHz) Proposed
V RGB Input (PC)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PC
640 x 350
640 x 350
720 x 400
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
848 x 480
848 x 480
848 x 480
852 x 480
852 x 480
852 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
31.468
37.861
31.469
37.927
31.469
35.000
37.861
37.500
43.269
31.5
37.799
39.375
31.5
37.799
39.375
35.156
37.879
48.077
46.875
53.674
49.725
70.09
85.08
70.08
85.03
59.94
66.66
72.80
75.00
85.00
60.00
70.00
75.00
60.00
70.00
75.00
56.25
60.31
72.18
75.00
85.06
74.55
25.17
31.50
28.32
35.50
25.17
30.24
31.50
31.50
36.00
33.516
40.748
42.628
33.642
40.900
42.840
36.00
40.00
50.00
49.50
56.25
57.28
EGA
EGA
DOS
DOS
VESA(VGA)
Macintosh
VESA(VGA)
VESA(VGA)
VESA(VGA)
WVGA
WVGA
WVGA
WVGA
WVGA
WVGA
VESA(SVGA)
VESA(SVGA)
VESA(SVGA)
VESA(SVGA)
VESA(SVGA)
Macintosh
No Resolution H-freq (kHz) V-freq (Hz) Pixel clock (MHz) Proposed

- 20 -
24
25
26
27
28
29
30
31
32
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1152 x 864
1152 x 864
1152 x 870
1280 x 960
1280 x 1024
48.363
56.476
60.023
54.348
63.995
67.500
68.681
60.023
63.981
60.00
70.06
75.02
60.05
70.01
75.00
75.06
60.02
60.02
65.00
75.00
78.75
80.00
94.20
108.00
100.00
108.00
108.00
VESA(XGA)
VESA(XGA)
VESA(XGA)
VESA(SXGA)
VESA(SXGA)
VESA(SXGA)
VESA(SXGA)
VESA(SXGA)
VESA(SXGA)
No Resolution H-freq (kHz) V-freq (Hz) Pixel clock (MHz) Proposed
1
2
3
1024 x 576
1920 x 1080
1920 x 1080 (+72)
31.250
28.125
31.250
50.00
50.00
50.00
27.027
74.250
74.250
MT-42PZ4x
MT-42PZ4x
MT-42PZ4x
No Resolution H-freq (kHz) V-freq (Hz) Pixel clock (MHz) Remarks
1
2
3
4
5
6
7
8
9
10
Display area
Outline dimension
Number of Pixels
Number of Grdations
Color Arrangement
weight(net)
weight(gross)
Operating Environment
Storage Enironment
Image stick Starts time
minimization moe
The minimum
brightness reaching
t ime
920.1(H) x 518.4(V) +/- 0.5
1006(W) x 598(H) x 6(D) +/- 1
852(H) x 480(V)
256 steps For PC RGB
RGB Vertical Stripes
15.3 15.8 16.3
106 111 116
Temp : 0 ~ 40
Humidity : 20 ~ 80%
Temp : -20 ~ 60 deg
Humidity : 10 ~ 90%
4.5 5 5.5
14 15 16
Mm
Mm
kg
Kg
Deg
%
Deg
%
Min
Min
Fish Bone Type
Modules 5EA/ 1Box
No Resolution Min Type Max Unit Remarks
V RGB Input (DTV)
V PDP MODULE (PDP42V5####)