Life Fitness Club Series User manual

Club Series Cross-Trainer
Assembly Instructions

Congratulations...
and welcome to the world of
and the Life Fitness Club Series Cross-Trainers.
The following Parts List and the step by step assembly procedures have been assem-
bled to make the set-up of the Cross-Trainer as quick and easy as possible.
Please take special note of the following important points prior to choosing a location
and beginning assembly of the Cross-Trainer.
.

IMPORTANT SAFETY INSTRUCTIONS!
YDO NOT locate the Cross-Trainer outdoors, near swimming pools, or in areas of high humidity.
YDO NOT operate your Cross-Trainer if it has been dropped, damaged, or even partially
immersed in water. If this occurs, contact Life Fitness Customer Support Services at the num-
ber in the Operation Manual.
YDO NOT locate the Cross-Trainer any closer than 30 inches (76cm) to a television set.
YDO NOT locate additional Cross-Trainers any closer than 42 inches (107cm) from center to
center to avoid interference (cross talk) between Heart Rate monitors.
YDO keep the area around your Cross-Trainer clear of any obstructions, including walls and fur-
niture. Ensure that there is at least a 12 inch (30cm) clearance in front of the Cross-Trainer.
YDO verify the contents of the delivery carton against the accompanying Parts List prior to set-
ting the cartons and shipping material aside. If any parts are missing, contact Life Fitness
Customer Support Services at the number listed in the Operation Manual. Save the shipping
cartons in case of return.
YDO read the entire Operation Manual prior to attempting to operate this machine as this is
essential for proper use.
CONSIGNES DE SECURITE IMPORTANTES!
YNE placez PAS l'appareil à l'extérieur, près d'une piscine ou dans un endroit très humide
YNE faites PAS fonctionner l'appareil s'il est tombé, s'il a été endommagé ou s'il a été partielle-
ment plongé dans l'eau. Si cela s'est produit, contactez le service après-vente de Life Fitness
au numéro fourni dans le manuel d'utilisation
YNE placez PAS l'appareil à moins de 76 cm d'un poste de télévision
YNE placez PAS d'autres appareils du même type à proximité. Un espace d'au moins 107 cm
doitêtre observé entre les parties centrales de deux appareils afin d'éviter les interférences
entre lescontrôleurs de rythme cardiaque.
YMAINTENEZ la zone autour de l'appareil libre de toute obstruction, y compris murs et meubles.
Veillez à laisser un dégagement d'au moins 30 cm devant l'appareil ?
YVÉRIFIEZ si l'emballage contient toutes les pièces de la liste jointe avant de le mettre de côté.
Si des pièces sont absentes, contactez le service après-vente de Life Fitness au numéro
indiquédans le manuel d'utilisation. Conservez l'emballage au cas où vous devriez renvoyer
l'appareil.?
YLISEZ le manuel de l'utilisateur tout entier avant d'essayer de faire fonctionner cet appareil.
Ceci est indispensable à son utilisation correcte.

TOOLS REQUIRED FOR ASSEMBLY...
Magnetic #2 Bit Phillips Screwdriver, 5/16" & 3/16" Hex Key Wrenches, 1/2" Open End Wrench
PARTS LIST
1” 2” 3” 4” 5”
1
8
2
3
1Hex socket Head Cap Screw Qty: 8 2 Phillips Pan Head Screw Qty: 8
3/8-16 x 1” #8-18 x 10”
0017-00101-1645 0017-00101-1744
3Phillips Pan Head Screw Qty: 14 4 Console Assembly Qty: 1
#8-18 x 3/4” AK61-00193-0001
0017-00101-1242
5Front Monocolumn Cover Qty: 1 6 Back Monocolumn Cover Qty: 1
0K61-06350-0003 0K61-06351-0003
7Console Support Assembly Qty: 1 8 Flat Washer Qty: 2
AK61-00500-0015 0017-00104-0192
9Left Front Cover Qty: 1 10 Right Front Cover Qty: 1
0K61-06200-0004 0K61-06210-0004
11 Left User Arm Assembly Qty: 1 12 Right User Arm Assembly Qty: 1
AK61-00178-0002 AK61-00178-0001
13 Front Rocker Cover Qty: 2 14 Back Rocker Cover Qty: 2
0K61-06340-0003 0K61-06341-0003
15 Foam Isolator (Polar® Receiver) Qty: 1 16 Polar® Receiver Qty: 1
0K36-01059-0002 AK40-00045-0001
17 Accessory Tray Qty: 1 18 Internal Tooth Lock Washer Qty: 6
0K63-01030-0001 0017-00104-0450
19 Cap: Console Support Qty: 1
0K61-01283-0001

Step 1
Before proceeding, familiarize yourself with the
parts of the Cross-Trainer and make sure that you
have received all the items described in the Parts
List.
Step 2
Locate the left and right FRONT COVER (#9,
#10). Using two PHILLIPS PAN HEAD SCREWS
(#3), mount the USER LEFT FRONT COVER (#9)
to the FRAME (A). Attach the USER RIGHT
FRONT COVER (#10) to the FRAME in the same
manner using two PHILLIPS PAN HEAD
SCREWS (#3). Secure the tops of the FRONT
COVERS together using two PHILLIPS PAN
HEAD SCREWS (#3).
Step 3
Locate the RIGHT USER ARM (#12). Snap the 2-PIN CONNEC-
TOR (2PA) located at the bottom of the RIGHT USER ARM into the
2-PIN CONNECTOR (2PB) positioned at the top of the RIGHT
ROCKER ARM (B). Feed the connectors and excess cable up into
the RIGHT USER ARM. Secure the RIGHT USER ARM to the
RIGHT ROCKER ARM using three HEX SOCKET HEAD CAP
SCREWS (#1) and INTERNAL TOOTH LOCK WASHERS (#18).
Repeat the procedure for the LEFT USER ARM (#11) and LEFT
ROCKER ARM (C). Tighten all screws securely.
CAUTION: BE CAREFUL NOT TO PINCH THE WIRE
HARNESSES WHEN ASSEMBLING THE USER ARMS
(#11 & #12) TO THE ROCKER ARMS (B & C).
MISE EN GARDE : VEILLEZ À NE PAS PINCER LEFAIS-
CEAU DE CÂBLES LORS DE L'ASSEMBLAGEDES
POIGNÉES MOBILES (Nº 11 et 12) ET DES BRASBASCU-
LANTS (B ET C).

Step 4
Detach and unwrap the WIRE HARNESS (E) (10P, 3P, 4P) located at the top of
the MONOCOLUMN (F). Holding the CONSOLE SUPPORT ASSEMBLY
(#7) with the handgrips facing upward, feed the WIRE HARNESS up
through the neck and out the top access hole. Carefully lower the CON-
SOLE SUPPORT ASSEMBLY into the MONOCOLUMN.
CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HAR-
NESSES (E) WHEN ASSEMBLING THE CONSOLE SUP-PORT
ASSEMBLY (#7) TO THE MONOCOLUMN (F).
MISE EN GARDE : VEILLEZ À NE PAS PINCER LE FAIS-
CEAU DE CÂBLES (E) LORS DU MONTAGE DU SUP-
PORTDE LACONSOLE (Nº 7) SUR LACOLONNE CEN-
TRALE (F).
Step 5
Using two HEX SOCKET HEAD CAP SCREWS (#1) and two FLAT
WASHERS (#8), secure the CONSOLE SUPPORTASSEMBLY (#7) to
the MONOCOLUMN (F). Tighten the screws securely.
Step 6
Locate the ACCESSORY TRAY (#17). Align the ACCESSORY TRAY
with the bottom of the DISPLAY CONSOLE (#4) as shown. Using four
MOUNTING SCREWS (#2), secure the ACCESSORY TRAY to the
DISPLAY CONSOLE as shown. Tighten the screws securely.
CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS
HEADPAN SCREWS (#2).
MISE EN GARDE : NE SERREZ PAS TROPLES VIS CRUCI-
FORMES À TÊTE CYLINDRIQUE (Nº 2)
Step 7
Attach the 3-PIN (3P), 4-PIN (4P) and 10-PIN (10P) CONNECTORS to the corresponding jacks on the back of the CON-
SOLE ASSEMBLY (#4).
Step 8
Feed any excess WIRE HARNESS (E) down into the CONSOLE SUPPORT ASSEMBLY (#7). Secure the CONSOLE
ASSEMBLY (#4) to the CONSOLE SUPPORT ASSEMBLY using four PHILLIPS PAN HEAD SCREWS (#2). Tighten the
screws securely.
CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS HEAD PAN SCREWS (#2).
CAUTION: BE CAREFUL NOT TO PINCH THE WIRE HARNESS (E) WHEN ASSEMBLING THE CONSOLE
ASSEMBLY (#4) TO THE CONSOLE SUPPORT ASSEMBLY (#7).
MISE EN GARDE : NE SERREZ PAS TROPLES VIS CRUCIFORMES À TÊTE CYLINDRIQUE (Nº 2).
MISE EN GARDE : VEILLEZ À NE PAS PINCER LE FAISCEAU DE CÂBLES (E) LORS DU MONTAGE DE
LACONSOLE (Nº 4) SUR SON SUPPORT (Nº 7).
Step 9
Locate and install the CONSOLE SUPPORT CAP (#21) onto the CONSOLE SUPPORT ASSEMBLY (#7) as shown.

Step 10
Locate the POLAR RECEIVER (#16). Slide the FOAM ISO-
LATOR #15) over the POLAR RECEIVER. Remove
the POLAR RECEIVER JACK (G) from the tape
and plug the POLAR RECEIVER into the POLAR
RECEIVER JACK.
Step 11
Locate the front and back MONOCOLUMN
COVERS (#5 & #6). With the wire positioned on top,
carefully insert the POLAR RECEIVER (#16) between
the vertical ribs located inside the BACK MONOCOLUMN
COVER(#6).
Place the BACK MONOCOLUMN COVER (#6) over the PIVOT
SHAFT (H) at the top of the MONOCOLUMN (F).
NOTE: THE POLAR RECEIVER WIRE MUST BE POSITIONED ON TOP
WHEN INSERTED INTO THE REAR MONOCOLUMN COVER(#6).
REMARQUE :LE FILDU RÉCEPTEUR POLAR DOIT ÊTRE PLACÉ SUR LE DESSUS
LORS DE L'INSERTION DANS LE CACHE ARRIÈRE DE LACOLONNE CENTRALE (Nº 6).
Step 12
Place the FRONT MONOCOLUMN COVER(#5) on the opposite side of the BACK MONOCOLUMN COVER (#6) to
cover the PIVOT SHAFT(G) and CONSOLE SUPPORT ASSEMBLY MOUNTING SCREWS. Interlock the top
tabs and use two PHILLIPS PAN HEAD SCREWS (#3) to secure the bottoms of MONOCOLUMN COVERS together.
Tighten the screws securely.
CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS PAN HEAD SCREWS (#3).
MISE EN GARDE : NE SERREZ PAS EXCESSIVEMENT LES VIS CRUCIFORMES À TÊTE CYLINDRIQUE
(Nº 3).
Step 13
Locate one FRONT ROCKER COVER (#13) and one BACK ROCKER COVER (#14). Position the FRONT
ROCKER COVER over the user side of the left end of the PIVOT SHAFT(H) (as shown) making sure that it
interlocks with the MONOCOLUMN COVERS (#5 & #6). Place the BACK ROCKER COVER over the opposite
side of the left end of the PIVOT SHAFT in the same manner. Secure the covers using three PHILLIPS PAN
HEAD SCREWS (#3). Repeat the procedure reversing front and back for the user right end of the pivot shaft.
CAUTION: DO NOT OVER-TIGHTEN THE PHILLIPS PAN HEAD SCREWS (#3).
MISE EN GARDE : NE SERREZ PAS EXCESSIVEMENT LES VIS CRUCIFORMES À TÊTE CYLINDRIQUE
(Nº 3).

PRE-OPERATION CHECKLIST
Ensure that all fasteners are tight.
Make sure the CROSS-TRAINER is properly leveled and stable. (Refer to the
Operation Manual).
Ensure that the Leveler Jam Nuts are tight. (Refer to the Operation Manual).
Read the entire Operation Manual before using the Cross-Trainer.
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LAMISE EN MARCHE
Vérifiez si tous les dispositifs de fixation sont serrés.
Vérifiez si l'APPAREILD'EXERCICE POLYVALENT est de niveau et stable.(Référez-
vous au manuel d'utilisation.)
Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.(Référez-vous au
manuel d'utilisation.)
Lisez le manuel d'utilisation dans son intégralité avant d'utiliser l'appareil d'exercice
polyvalent.
Before attempting to operate your Cross-Trainer, it is imperative that you familiarize yourself with the contents of the
Operation Manual. If your Cross-Trainer does not respond as described in the Operation Manual, contact the nearest
Life Fitness service center as listed in the Operation Manual Life Fitness Customer Support Services.
Copyright 2007 Brunswick Corporation. All rights reserved. Life Fitness is a trademark of Brunswick
Corporation.Polar is a registered trademark of Polar Electro, Inc
M051-00K61-A-118
09/07