Life Gear FLIP TRACK II 97270 User manual

FLIP TRACK II
MOTORIZED TREADMILL
ITEM NO: 97270
OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without
notice. 2012, May

1
TABLE OF CONTENTS
WARRANTY ------------------------------------------------------------------------------- 2
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 3
PARTS LIST -------------------------------------------------------------------------------- 5
SILICONE OIL INCLUDED ------------------------------------------------------------- 6
TOOL ----------------------------------------------------------------------------------------- 6
OVERVIEW DRAWING ----------------------------------------------------------------- 7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
LIFTING UP AND SETTING DOWN THE TREADMILL -------------------------10
STORAGE ---------------------------------------------------------------------------------- 11
OPERATING THE COMPUTER ------------------------------------------------------ 12
CARE, MAINTENANCE & TROUBLESHOOTING GUIDE --------------------- 14
BELT ADJUSTMENT AND LUBRICATION ---------------------------------------- 15
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 16

2
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that
it has been installed and operated in accordance with LifeGear's Owner's Manual.
LifeGear's obligation under this warranty is limited to replacing or repairing free of charge,
any parts which may prove to be defective under normal home use. This warranty does
not include any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is offered only to the original owner and is not transferable. Proof of
purchase is required.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

3
IMPORTANT SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this treadmill: Read all instructions before using this
treadmill.
DANGER:To reduce the risk of electric shock, please read the following:
zAlways unplug the treadmill from the electrical outlet immediately after using and
before cleaning, assembling, or servicing.
NOTE: Failure to follow these instructions may lead to personal injury and cause
damage to the treadmill.
WARNING: To reduce the risk of burns, fire, electric shock or injury to any
persons, please read the following:
zNever leave the treadmill unattended when plugged in. Disconnect by turning off the
master power switch, and unplugging from outlet when not in use and before putting
on or taking off parts.
zUse this appliance only for its intended use as described in this manual. Do not use
attachments not recommended by the manufacturer.
zNever operate this treadmill if it has a damaged cord or plug, or if it is not working
properly. If it has been dropped or damaged, or been exposed to water, return the
appliance to a service center for examination and repair.
zDo not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
zNever operate the appliance with the air openings blocked. Keep the air openings
free of lint, hair, and the like.
zDo not use the treadmill outdoors.
zDo not pull the treadmill by its power cord or use the cord as a handle.
zKeep children and pets away from the equipment while in use. This machine is
designed for adults only. Close supervision is necessary when this treadmill is used
by on, near invalids or disabled persons.
zDo not operate where aerosol (spray) products are being used or where oxygen is
being administered.
zKeep Dry - do not operate in a wet or moist condition. Save these instructions.
zDo not operate the treadmill near a blanket. Excessive heating can occur and cause
fire, electrical shock, or injury to user.
zKeep electrical cord away from heated surfaces.
zNever insert any object into any opening.
zKeep the treadmill on a solid, level surface with the minimum safety area clearance of
2000mm x 1000mm of the treadmill. Be sure the area around the treadmill remains
clear during use and has adequate clearance.
zThis treadmill is for household use only.
zOnly one person should be on the treadmill while in use.
zWear comfortable and suitable clothing when using the treadmill. Do not use the
treadmill barefoot, in only socks or in sandals, always wear athletic shoes. Never
wear loose clothing because it could run the risk of getting caught in the treadmill.
zAlways hold on to the handrails while using the treadmill.
zAlways make sure the storage latch is in place when folding and moving the treadmill.
zDo not leave children who are under 12 year-old unsupervised near or on the treadmill.
zTo disconnect, turn all controls to the off position, then remove plug from outlet.

4
zThis appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
zIf the supply cord is damaged, it must be replaced by the manufacture, its service
agent or similarly qualified persons in order to avoid a hazard.
zPull up the Safety Tether Key for emergency stop. Reinstall the Safety Tether Key
onto the Computer Console. Press the START button and then press the SPEED +
button to begin exercise again.
zMaximum Weight Capacity for this product is 110 kgs.
Note: It is the obligation of the owner to review and explain these safety precautions
to all users of this treadmill.
WARNING: Connect the treadmill to a properly grounded outlet only.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
zThis product must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electric current reducing the risk of electric
shock. * This treadmill is equipped with a cord having equipment grounding
conductor and a grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance with all local codes
and ordinances.
DANGER:Improper connection of the treadmill grounding conductor can result
in the risk of electric shock. Check with a qualified electrician, if you are in doubt as to
whether the product is properly grounded. Do not modify the plug provided with the
treadmill. If it will not fit your outlet, have a properly grounded outlet installed by a qualified
electrician.
Make sure that the product is connected to an outlet having the same configuration as the
plug.
zThis unit must be plugged into a nominal 220 volt 50/60Hz, which has a grounding.
zKeep hands clear of all moving parts. Never place hands, feet under the treadmill.
zDo not use the treadmill on a carpet that is greater than 1/2 inch in height.
zBefore using the treadmill, check that the belt is aligned and centered on the walking
deck and all visible fasteners on the treadmill are sufficiently tightened and secure.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness equipment.
We assume no responsibility for personal injury or property damage sustained by or
through the use of this product. Do not operate this exercise equipment without properly
fitted guards, as the moving parts can present a risk of serious injury to young children.
CAUTION:Read all instructions carefully before operating this product. Retain
this Owner’s Manual for future reference.

5
PARTS LIST
No. Description Qty No. Description Qty
001 Main Frame 1 035 Power Cord 1
002 M8x60 Bolt 2 036 Drive Motor 1
003R Rear Right Cap for Main Frame 1 037 Power Control Board 1
003L Rear Left Cap for Main Frame 1 038 Power Cord Cap 1
004 Computer 1 039 Power Switch 1
005 Bottom Cover for Computer 1 040 Fuse Box 1
006 M6 Nylon Nut 10 041 M4x8mm Screw 4
007 ST4x16 Screw 9 042 Wire for Fuse Box 1
008 ST4x50 Screw 4 043 Cable Switch/PCB 1
009 M8x40 Bolt 2 044 Base Frame Support Tube Knob
M8x68 2
010 M8 Spring Washer 4 045 Belt (6V160 ) 1
011 M4x12 Bolt 4 046 Front Roller 1
012 M4 Nylon Nut 4 047 Running Belt 2220x405x1.6t 1
013 Wire Cap 1 048 Running Deck 985x491x18t 1
014 Spacer Ø16xØ11x19 2 049 M6x33 Bolt 8
015 Motor Cover 1 050R Right Side Rail 1
016 Rectangular End Cap □50x25 2 050L Left Side Rail 1
017 M8x35 Bolt 2 051 Rubber Bumper 8
018 Square End Cap □20x20 1 052 M8x45 Bolt 1
019 M8 Nylon Washer 1 053 Motor Base 1
020 M8 Nylon Nut 5 054 M8x12 Round Head Bolt 2
021 Safety Tube B 1 055 Rear Roller 1
022 Square Bushing 1 056 M8 Cap Nut 2
023 Spring Knob 1 057 Base Frame 1
024 Safety Tube A 1 058 Handlebar End Cap Ø38 2
025 Round End Cap Ø38 2 059 Handlebar Foam Grip
Ø30x235x3t 2
026 Square End Cap □25x25 1 060 Spacer Ø12xØ9x21.5 2
027 Transport Wheel Ø50xØ8.5 2 061 Spacer Ø12xØ10.5x14 4
028 Adjustable Leveler 5 062 ST5x18 Screw 2
029 M8x60 Bolt 2 063 Safety Tether Key 1
030R Right Base Frame Support Tube 1 064 ST4x22 Screw 15
030L Left Base Frame Support Tube 1 065 Sensor Bracket 1
031 M10x100 Bolt 2 066 Sensor 1
032 Sensor Cable I (680 mm.) 1 067 Handlebar Knob M8x12 2
033 Sensor Cable II (1650 mm.) 1 068 Handlebar 1
034 M10 Nylon Nut 2

6
SILICONE OIL INCLUDED
TOOL
Silicone Oil
1 PC
Allen Wrench
1 PC

7
OVERVIEW DRAWING
28
57
28
31
28
30R
56
33
29
27
44
28
28
44
56
29
27
30L
38
61
35
61
31
1
51
51
25
25
3R
3L
2
7
6
7
6
52 12
11
20
54
10
53
1314
14
10
9
10
9
60
60
65
7
66
16
40 39
37
42
43
16
55
46
45
48
50L
50R
49
47
15
36
17
18
20
19 21
22
24
23 26
34
34
17
8
2
41
41
58
67
59
33
62
4
5
63
67
62
68
64
64
32
6
6
32
59
64
58

8
30R
57
44
30L
44
ASSEMBLY INSTRUCTIONS
Step 1
Remove the treadmill from the carton and place it in a vertical position on a solid, level
surface.
NOTE: It is recommended that you always use the aid of a second person when
removing the treadmill from the carton and place it in a vertical position.
․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․
Step 2
To set down the treadmill, place one hand on the back end of the treadmill and the other
hand to pull the Spring Knob (23), then carefully lower the deck to the ground until the
Spring Knob (23) "pops" down into the locked position.
Attach both Right/Left Base Frame Support Tubes (30R, 30L) into the Base Frame (57)
with two M8x68 Base Frame Support Tube Knobs (44).

9
Step 3
Pull the Handlebar (68) all the way down, then attach both M8x12 Handlebar Knobs (67)
onto the Handlebar (68) and right/left handlebar support tubes of the Base Frame (57).
Place the Safety Tether Key (63) onto the Computer (4).
67
67
63
68
57
4

10
LIFTING UP AND SETTING DOWN THE TREADMILL
LIFTING UP THE TREADMILL
To lift up the treadmill, place one hand on the back end of the treadmill and the other hand
to pull the Spring Knob. Carefully lift the end of the treadmill up into the upright position
until the Spring Knob "pops" down into the locked position. Make sure the deck is securely
locked before moving the treadmill. (See diagrams A and B.)
The unit can be carefully tilted onto its transport wheels for easy moving and storage.
Store the treadmill in a clean and dry environment away from children.
SETTING DOWN THE TREADMILL
To set down the treadmill, place one hand on the back end of the treadmill and the other
hand to pull the Spring Knob, then carefully lower the deck to the ground until the Spring
Knob "pops" down into the locked position. (See diagrams C and D.)
NOTE: Do not stand under the deck when setting down the treadmill.
TO PREVENT INJURY PLEASE MAKE SURE YOU HAVE A FIRM HOLD WHEN
LIFTING UP OR SETTING DOWN THE DECK.
A
Spring Knob
B
D
C
Spring Knob

11
STORAGE
Place one hand on the back end of the treadmill and the other hand to pull the Spring
Knob. Carefully lift the end of the treadmill up into the upright position until the Spring
Knob "pops" down into the locked position. Check the Spring Knob is "pop" down into the
locked position before removing the M8x12 Handlebar Knobs. Remove both M8x12
Handlebar Knobs from the Handlebar and right/left handlebar support tubes of the Base
Frame. Push the Handlebar all the way up and then attach both M8x12 Handlebar Knobs
back onto the right/left handlebar support tubes of the Base Frame that were removed.
(See diagrams A, B, and C.)
A
Handlebar Knob
M8x12
BC

12
OPERATING THE COMPUTER
Quick Start:
Flip the Master Power Switch that is located at the front of the treadmill to the ON position.
Before beginning a workout session ensure that the Safety Tether Key is properly installed
onto the Computer Console and the Safety Clip is securely attached to an article of your
clothing. Always begin the treadmill standing on the side rails, not on the running belt.
Press the START button and then press the SPEED + button to start exercise. The
running belt will start moving with an initial speed of 0.8 KPH. The TIME window will
display your elapsed workout time. The DISTANCE window will display the accumulative
distance traveled during workout. You may press the SPEED + or SPEED - button on the
computer console to increase or decrease the running speed during exercise. The
treadmill’s speed range is from 0.8 KPH to 12.0 KPH. The SPEED window will display the
current running speed. During training, you may press the STOP button to pause the
treadmill running at any time, press the START button to start the treadmill running again.
You may also press the STOP button to stop the treadmill running during exercise, or pull
out the safety tether key to stop the treadmill running.
Button Functions:
START: To start training.
STOP: To stop training.
MODE: To select time or distance for target pre-setting. Press the MODE button for 3
seconds will reset the values of time or distance to zero.
SET: To set time or distance for target pre-setting.
SPEED +: Speed up adjustment during exercise.
SPEED -: Speed down adjustment during exercise.
Computer Functions:
TIME: Displays your elapsed workout time in minutes and seconds. Press the START
button and then press the SPEED + button to start exercise. The running belt will start
moving with an initial speed of 0.8 KPH. You may press the SPEED + or SPEED – button
on the computer console to increase or decrease the running speed during exercise. Time
starts counting up from 0:00 to 99:59 per 1 second increment. You may also pre-set target
time in STOP mode before training. To set TIME press the MODE button until you see the
TIME begin blinking. Press the SET button to change the time, each time you press the
SET button TIME should change by 1 minute. Press the MODE button for 3 seconds will

13
reset the target values of time to zero. The pre-set target time range is from 0:00 to 99:00
minutes. Once you pre-set target time, press the START button and then press the
SPEED + button to start exercise. The running belt starts moving at a speed of 0.8 KPH.
You may press the SPEED + or SPEED - button on the computer console to increase or
decrease the running speed during exercise. TIME starts counting down from pre-set
target time to 0:00 per 1 second backward. When the pre-set target time counts down to
0:00, the computer will begin beeping to remind you and the running belt will stop
automatically.
SPEED: Display the current running speed from the minimum 0.8 KPH to the maximum
12 KPH. You may also press the SPEED + or SPEED - button to increase or decrease
the running speed during exercise.
DISTANCE: Displays the accumulative distance traveled during workout. Press the
START button and then press the SPEED + button to start exercise. The running belt will
start moving with an initial speed of 0.8 KPH. You may press the SPEED + or SPEED -
button on the computer console to increase or decrease the running speed during exercise.
You may also pre-set target distance in STOP mode before training. To set DISTANCE
press the MODE button until you see the DISTANCE begin blinking. Press the SET button
to change the distance, each time you press the SET button DISTANCE should change by
0.1 km. Press the MODE button for 3 seconds will reset the target values of distance to
zero. The pre-set target distance range is from 0.0 to 99.9 km. Once you pre-set target
distance, press the START button and then press the SPEED + button to start exercise.
The running belt starts moving at a speed of 0.8 KPH. You may the press the SPEED + or
SPEED - button on the computer console to increase or decrease the running speed
during exercise. Distance starts counting down from pre-set target distance to 0.0. When
the pre-set target distance counts down to 0.0, the computer will begin beeping to remind
you and the running belt will stop automatically.

14
CARE, MAINTENANCE & TROUBLESHOOTING GUIDE
WARNING: To prevent electrical shock, please turn off and unplugg(ed) the treadmill
before cleaning or performing routine maintenance.
CLEANING
The treadmill can be cleaned with a soft cloth and mild detergent. Do not use abrasives or
solvents. Be careful not get excessive moisture on the display panel as this might cause
an electrical hazard or electronics to fail.
Please keep the treadmill, especially, the console, out of direct sunlight to prevent screen
damage.
STORAGE
Store the treadmill in a clean and dry environment. Ensure the master power switch is off
and is in the off position and the power plug is un-plugged from the electrical wall outlet.
TROUBLESHOOTING GUIDE
1.
A
pply silicone lubricant.
2. Adjust belt tension.
Adjust belt tension.
1. Put the power plug into the
electrical wall outlet.
2. Install the safety tether key.
3. Reset or have an electrician
replace the breaker in home.
4. Wait five minutes and then
press the switch back in.
Center the belt.
Problem
Treadmill will not
start.
Belt slips.
Belt is off
centered.
Potential Causes
1. Not plugged in.
2. Safety tether key not
connected.
3. House circuit breaker
tripped.
4. Treadmill circuit breaker
tripped.
Belt not tight enough.
1. Not enough lubrication
applied onto the running
deck.
2. Belt is too tight.
Running belt tension not
even across the rear roller.
Corrections
Belt hesitates
When stepped
on.

15
BELT ADJUSTMENT AND LUBRICATION
Belt Adjustment:
The belt is adjusted at the factory; it may come loose during transportation and/or from use.
After prolong use of the treadmill, the belt will stretch out. If the belt is shifting to the left,
turn on the main power switch of treadmill and let the belt run at the speed of 2-3 KPH.
Using the Allen Wrench provided, turn the left rear roller adjustment bolt 1/4 turn in the
clockwise direction. You should see the belt start to correct itself by moving back toward
the center. Repeat the above procedure until the belt is properly centered. If the belt is
shifting to the right, turn on the main power switch of treadmill and let the belt run at the
speed of 2-3 KPH. Using the Allen Wrench provided, turn the right rear roller adjustment
bolt 1/4 turn in the clockwise direction. You should see the belt start to correct itself by
moving back toward the center. Repeat the above procedure until the belt is properly
centered. If the belt is slipping during use, turn off and unplugged the treadmill. Using the
Allen Wrench provided, turn both left and right rear roller adjustment bolts 1/4 turn in the
clockwise direction for the same amount, then turn on the main power switch of treadmill
and let the belt run at the speed of 2-3 KPH. You should now walk on to the belt to
determine if the belt is still slipping. Repeat the above procedure until the belt no longer
slips.
Lubrication:
The treadmill has already been coated with "Silicone Oil" in advance. Silicone oil is a
non-volatile oil and by the time you receive should have permeated through the belt.
There will be no need to re-apply the oil under normal circumstances.
To maintain the belt, "Silicone Oil" may be re-applied once the resistance has been
increased and the belt starts rubbing against the running deck. To re-apply “Silicone Oil”
to the treadmill, lift up the belt, one side at a time, and apply the oil directly to the center of
the running deck. Allow the silicone oil to 'set' for one minute before using the treadmill.
Attention: Only use "Silicone Oil" lubricants for this equipment. In addition, do not add
any other type of oil; otherwise the treadmill will be damaged. Do not over-lubricate
the walking board. Excess lubricant should be wiped off with a clean towel.

16
WARM UP AND COOL DOWN ROUTINE
A good exercise program consists of a warm-up, aerobic exercise, and a cool down. Do
the entire program at least two to three times a week, resting for a day between workouts.
After several months you can increase your workouts to four or five times per week.
AEROBIC EXERCISE is any sustained activity that sends oxygen to your muscles via
your heart and lungs. Aerobic exercise improves the fitness of your lungs and heart.
Aerobic fitness is promoted by any activity that uses your large muscles eg: legs, arms and
buttocks. Your heart beats quickly and you breathe deeply. An aerobic exercise should
be part of your entire exercise routine.
The WARM-UP is an important part of any workout. It should begin every session to
prepare your body for more strenuous exercise by heating up and stretching your muscles,
increasing your circulation and pulse rate, and delivering more oxygen to your muscles.
COOL DOWN at the end of your workout, repeat these exercises to reduce soreness in
tired muscles.
HEAD ROLLS
Rotate your head to the right for one count, you should feel a
stretching sensation up the left side of your neck. Then rotate your
head back for one count, stretching your chin to the ceiling and
letting your mouth open. Rotate your head to the left for one count,
then drop your head to your chest for one count.
SHOULDER LIFTS
Lift your right shoulder toward your ear for one count. Then lift your
left shoulder up for one count as you lower your right shoulder.
SIDE STRETCHES
Open your arms to the side and lift them until they are over your head.
Reach your right arm as far toward the ceiling as you can for one
count. Repeat this action with your left arm.

17
QUADRICEPS STRETCH
With one hand against a wall for balance, reach behind you and pull
your right foot up. Bring your heel as close to your buttocks as
possible. Hold for 15 counts and repeat with left foot.
HAMSTRING STRETCHES
Extend your right leg. Rest the sole of your left foot
against your right inner thigh. Stretch toward your toe
as far as possible. Hold for 15 counts. Relax and then
repeat with left leg.
CALF/ACHILLES STRETCH
Lean against a wall with your left leg in front of the right and
your arms forward. Keep your right leg straight and the left
foot on the floor; then bend the left leg and lean forward by
moving your hips toward the wall. Hold, then repeat on the
other side for 15 counts.
TOE TOUCHES
Slowly bend forward from your waist, letting your back and
shoulders relax as you stretch toward your toes. Reach as far as
you can and hold for 15 counts.
INNER THIGH STRETCH
Sit with the soles of your feet together and your knees pointing
outward. Pull your feet as close to your groin as possible.
Gently push your knees toward the floor. Hold for 15 counts.