Life Gear POWER TRACK PRO 97370 User manual

POWER TRACK PRO
OWNER'S MANUAL
MODEL#97370

1
TABLE OF CONTENTS
ONE YEAR LIMTED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in material and workmanship when used for the purpose
intended, under the conditions that it has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's obligation under
this warranty is limited to replacing or repairing, free of charge, any parts which may prove to be defective under normal home use. This warranty
does not include any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year. This warranty is extended only to the original owner
and is not transferable. When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3.Description of Parts
4.Part Number
5.Date of Purchase
WARRANTY 1
SAFETY INSTRUCTIONS 2
OVERVIEWDRAWING 4
PARTS LIST 5
HARDWARE PACKING LIST 7
ASSEMBLY INSTRUCTIONS 8
FOLDINGUP& INCLINEADJUSTMENT 10
COMPUTER OPERATION 11
TROUBLE SHOOTINGGUIDE 14
RUNNINGBELTADJUSTMENT
ANDLUBRICATION 15
WARM UP AND COOLDOWN ROUTINE 16

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety instructions when using this treadmill: Read all
instructions before using this treadmill.
DANGER: To reduce the risk of electric shock, please read the following:
zAlways unplug the treadmill from the electrical outlet immediately after using and befor cleaning, assembling, or servicing.
NOTE: Failure to follow these instructions may lead to personal injury and cause damage to the treadmill.
WARNING: To reduce the risk of burns, fire, electric shock or injury to any persons, please read the following:
zNever leave the treadmill unattended when plugged in. Disconnect by turning off the master power switch, and unplugging from
outlet when not in use and before putting on or taking off parts.
zUse this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the
manufacturer.
zNever operate this treadmill if it has a damaged cord or plug, or if it is not working properly. If it has been dropped or damaged, or
been exposed to water, return the appliance to a service center for examination and repair.
zDo not attempt any maintenance or adjustments other than those described in this manual. Should any problems arise, discontinue
use and consult an Authorized Service Representative.
zNever operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and the like.
zDo not use the treadmill outdoors.
zDo not pull the treadmill by its power cord or use the cord as a handle.
zKeep children and pets away from the equipment while in use. This machine is designed for adults only.
zDo not operate where aerosol (spray) products are being used or where oxygen is being administered.
zKeep Dry - do not operate in a wet or moist condition. Save these instructions.
zDo not operate the treadmill near a blanket. Excessive heating can occur and cause fire, electrical shock, or injury to user.
zKeep electrical cord away from heated surfaces.
zNever insert any object into any opening.
zKeep the treadmill on a solid, level surface with the minimum safety area clearance of 2000mm x 1000mm of the treadmill. Be sure
the area around the treadmill remains clear during use and has adequate clearance.
zThis treadmill is for household use only.
zWear comfortable and suitable clothing when using the treadmill. Do not use the treadmill barefoot, in only socks or in sandals,
always wear athletic shoes. Never wear loose clothing because it could run the risk of getting caught in the treadmill.

3
zOnly one person should be on the treadmill while in use.
zAlways hold on to the handrails while using the treadmill.
zAlways make sure the storage latch is in place when folding and moving the treadmill.
zDo not leave children who are under 12 year-old unsupervised near or on the treadmill.
zPull up the Safety Tether Key for emergency stop. Reinstall the Safety Tether Key onto the Computer Console. Press the ON button to begin
exercise again.
Note: It is the obligation of the owner to review and explain these safety precautions to all users of this treadmill.
WARNING: Connect the treadmill to a properly grounded outlet only.
SAVE THESE INSTRUCTIONS
This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current
reducing the risk of electric shock. * This treadmill is equipped with a cord having equipment grounding connector and a
grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with
all local codes and ordinances.
DANGER: Improper connection of the treadmill grounding connector can result in the risk of electric shock. Check with a qualified
electrician, if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the treadmill. If it will
not fit your outlet, have a properly grounded outlet installed by a qualified electrician.
This product is for use on a nominal 220 volt circuit and has a grounding plug. Make sure that the product is connected to an outlet
having the same configuration as the plug.
zThis unit must be plugged into a nominal 220 volt 50/60 Hz, which has a grounding.
zKeep hands clear of all moving parts. Never place hands, feet under the treadmill.
zDo not use the treadmill on a carpet that is greater than 1/2 inch in height.
zBefore using the treadmill, check that the running belt is aligned and centered on the treadmill bed and all visible fasteners on the
treadmill are sufficiently tightened and secure.
WARNING: Before beginning any exercise program consult your physician. This is especially important for the
persons who are over 35 years old or who have pre-existing health problems. Read all instructions before using any fitness equipment.
We assume no responsibility for personal injury or property damage sustained by or through the use of this product. Do not operate this
exercise equipment without properly fitted guards, as the moving parts can present a risk of serious injury to young children.
CAUTION: Read all instructions carefully before operating this product. Retain this Owner's Manual for future reference.

4
OVERVIEWDRAWING
1
51
51 5
3
4
2
56
5656
7
6
7
6
17
12
11
20
54
74
53
13
14
14
74
9
74
9
73
73
72
7
34
16
4039 38
37
42
44
16
55
46
45
48
50L
50R
49
47 15
35
36
57
28
74
66
31R
31L
13
33
17
18
20
19 21
22
24
23
25
26
19
8
30L
58
64
61
59
60
62
63
68
60
29
62
70
71
29
32
32
33
75
79
79
80
80
74
74
66
66
28
30R
30L
81
27
64
64
76
76
65
65
80
80
69
81
27
82
83
78
77
74
5
63
7
10
20
20
75
20
84
7
41

5
Part # Description Quantity Part # Description Quantity
1 Main Frame 1
2 Bolt (M8x60mm) 2
3 Rear Cap (Right) 1
4 Rear Cap (Left) 1
5 Adjustable Pad 2
6 Nylon Nut (M6) 10
7 Tapping Screw (M4x16mm) 15
8 Screw (M4x50mm) 4
9 Bolt (M8x40mm) 2
10 Foot Pad 2
11 Bolt (M4x12mm) 3
12 Nut (M4) 3
13 Wire Cap 2
14 Spacer Ø 18xØ 10.5x35mm 2
15 Motor Cover 1
16 End Cap ( 25x50) 2
17 Bolt (M8x35mm) 2
18 Square End Cap ( 20) 1
19 Nylon Washer (M8) 2
20 Nylon Nut (M8) 8
21 Safety Tube A 1
22 Bushing 1
23 Spring Knob 1
24 Safety Tube B 1
25 Bolt (M8x40mm) 1
26 Square End Cap ( 25.4) 1
27 Bolt (M8x50mm) 2
28 End Cap for Stabilizer 2
29 Sensor Cable I 1
30R Handlebar Adorner (Right) 2
30L Handlebar Adorner (Left) 2
31R Handlebar Support (Right) 1
31L Handlebar Support (Left) 1
32 Sensor Cable II 1
33 Sensor Cable III 1
34 Sensor 1
35 Power Cord 1
36 Motor 1
37 Power Control Board 1
38 Wire Cap 1
39 Switch, AC Power 1
40 Fuse Box 1
41 Ring for Cable Power 2
42 Wire for Fuse Box 1
43
44 Cable Switch/PCB 1
45 Belt 1
46 Front Roller 1
47 Running Belt 1
48 Running Deck 1
49 Bolt (M6x33mm) 10
50R Side Rail (Right) 1
50L Side Rail (Left) 1
51 Deck Bumper 10
52
53 Motor Bracket 1
54 Bolt (M8x12mm) 2
55 Rear Roller 1
PARTS LIST

6
56 Screw (M4x8mm) 4
57 Stabilizer 1
58 End Cap for Handlebar 2
59 Foam Grip 2
60 Upper Hand Pulse Cover w/Wire 2
61 Lower Hand Pulse Cover 2
62 Speed Button w/Wire 1
63 Mode Button w/Wire 1
64 Screw (M3x20mm) 12
65 Spacer Ø 18xØ 10.5x15.5mm 2
66 Bolt (M8x16mm) 6
67
68 Handlebar 1
69 Incline Beam 1
70 Computer 1
71 Safety Tether Key 1
72 Bracket for Sensor 1
73 Spacer Ø 13.5xØ 8.5x22.5mm 2
74 Spring Washer (M8) 12
75 Wheel 2
76 Bolt (M10x40mm) 2
77 Cap Nut (M8) 2
78 Bolt (M5x10mm) 4
79 Bolt (M10x80mm) 2
80 Nylon Washer (M10) 4
81 Cover for Incline Beam 2
82 Meter Bracket 1
83 Carriage Bolt (M8x55mm) 2
84 Cylinder 1
Part # Description Quantity Part # Description Quantity
PARTS LIST

7
27 Bolt (M8x50)----------------------------------------------------------------------------------------------2
66 Bolt (M8x16)----------------------------------------------------------------------------------------------6
74 Spring Washer M8 --------------------------------------------------------------------------------------6
Part # Description Quantity
HARDWARE PACKING LIST

8
Step 1
Connect the Sensor Cable III (33) from the Stabilizer (57) to the Sensor Cable II (32) from the Right Handlebar Support (31R).
Insert the Right Handlebar Support (31R) to the Stabilizer (57) with three M8x16mm Bolts (66) and M8 Spring Washers (74).
Repeat above step to assemble the Left Handlebar Support (31L) to the Stabilizer (57).
Careful not to crimp, pinch or otherwise damage the cable and cable connections.
Step 2
Connect the Sensor Cable II (32) from the Right Handlebar Support (31R) to the Sensor Cable I (29) from the Handlebar (68).
Step 3
Attach the Handlebar (68) onto the top of Right and Left Handlebar Supports (31R, 31L) with two M8x50mm Bolts (27).
Careful not to crimp, pinch or otherwise damage the cable and cable connections.
ASSEMBLY INSTRUCTIONS
33
32
74 66
57
31R
31L
66
66
27
27
68
31L
31R
74
74
68
29
32
31R
123

9
Step 4
Assemble the Right and Left Handlebar Adorners (30R, 30L) to the Handlebar (68) with eight M3x20mm Screws (64).
Step 5
Attach the Computer Bracket (82) to the Handlebar (68) with two M8x55mm Carriage Bolts (83), M8 Spring Washers (74), and M8 Cap Nuts (77).
Step 6
Connect the Sensor Cable I (29), Upper Hand Pulse Cover with Wires (60), Speed Button Wire (62), and Mode Button Wire (63) to the wires
that come from the Computer (70). (See the small diagram of step 6).
Attach the Computer (70) onto the Computer Bracket (82) with four M5x10mm Bolts (78).
ASSEMBLY INSTRUCTIONS
63 29 62
60
68 82
83
82
77
74
68
68
64
30L
30L
30R
31R 64
31L
78
29
60
62
70
70
63
46
5