Life Gear 97288HP User manual

MOTORIZED TREADMILL
OWNER'S MANUAL
MODEL# 97288HP
The specifications of this product may vary from this photo and are subject to
changewithoutnotice. 2008, April
WALKEASE

1
PAGE OF CONTENTS
WARRANTY 1
SAFETYINSTRUCTIONS 2
OVERVIEWDRAWING 5
PARTSLIST 6
HARDWAREPACKINGLIST 7
ASSEMBLY INSTRUCTIONS 8
FOLDING UPAND SETTING DOWN 10
COMPUTEROPERATION 11
TROUBLE SHOOTING GUIDE 15
RUNNING BELTADJUSTMENT & LUBRICATION 16
WARM UP AND COOL DOWN ROUTINE 18
ONE YEAR LIMTED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from
defects in material and workmanship when used for the purpose intended,
under the conditions that it has been installed and operated in accordance with
LifeGear's Owner's Manual. LifeGear's obligation under this warranty is
limited to replacing or repairing, free of charge, any parts which may prove to
be defective under normal home use. This warranty does not include any
damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1
(one) year. This warranty is extended only to the original owner and is not
transferable. When ordering replacement parts please have the following
information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following
safety instructions when using this treadmill: Read all instructions
before using this treadmill.
DANGER:To reduce the risk of electric shock, please read the
following:
zAlways unplug the treadmill from the electrical outlet immediately after
using and before cleaning, assembling, or servicing.
NOTE: Failure to follow these instructions may lead to personal injury
and cause damage to the treadmill.
WARNING:To reduce the risk of burns, fire, electric shock or injury
to any persons, please read the following:
zNever leave the treadmill unattended when plugged in. Disconnect by
turning off the master power switch, and unplugging from outlet when not
in use and before putting on or taking off parts.
zUse this appliance only for its intended use as described in this manual.
Do not use attachments not recommended by the manufacturer.
zNever operate this treadmill if it has a damaged cord or plug, or if it is not
working properly. If it has been dropped or damaged, or been exposed
to water, return the appliance to a service center for examination and
repair.
zDo not attempt any maintenance or adjustments other than those
described in this manual. Should any problems arise, discontinue use
and consult an Authorized Service Representative.
zNever operate the appliance with the air openings blocked. Keep the air
openings free of lint, hair, and the like.
zDo not use the treadmill outdoors.
zDo not pull the treadmill by its power cord or use the cord as a handle.
zKeep children and pets away from the equipment while in use. This
machine is designed for adults only. Close supervision is necessary
when this treadmill is used by invalids or disabled persons.
zDo not operate where aerosol (spray) products are being used or where
oxygen is being administered.
zKeep Dry - do not operate in a wet or moist condition. Save these

3
instructions.
zDo not operate the treadmill near a blanket. Excessive heating can
occur and cause fire, electrical shock, or injury to user.
zKeep electrical cord away from heated surfaces.
zNever insert any object into any opening.
zKeep the treadmill on a solid, level surface with the minimum safety area
clearance of 2000mm x 1000mm of the treadmill. Be sure the area
around the treadmill remains clear during use and has adequate
clearance.
zThis treadmill is for household use only.
zOnly one person should be on the treadmill while in use.
zWear comfortable and suitable clothing when using the treadmill. Do not
use the treadmill barefoot, in only socks or in sandals, always wear
athletic shoes. Never wear loose clothing because it could run the risk of
getting caught in the treadmill.
zAlways hold on to the handrails while using the treadmill.
zAlways make sure the storage latch is in place when folding and moving
the treadmill.
zDo not leave children who are under 12 year-old unsupervised near or on
the treadmill.
zThis appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
zPull up the Safety Tether Key for emergency stop. Reinstall the Safety
Tether Key onto the Computer Console. Press the START button first
and then press the SPEED + button to begin exercise again.
Note: It is the obligation of the owner to review and explain these safety
precautions to all users of this treadmill.
WARNING: Connect the treadmill to a properly grounded outlet
only.
SAVE THESE INSTRUCTIONS
zThis product must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current reducing

4
the risk of electric shock. * This treadmill is equipped with a cord
having equipment grounding connector and a grounding plug. The
plug must be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and
ordinances.
DANGER:Improper connection of the treadmill grounding
connector can result in the risk of electric shock. Check with a qualified
electrician, if you are in doubt as to whether the product is properly grounded.
Do not modify the plug provided with the treadmill. If it will not fit your outlet,
have a properly grounded outlet installed by a qualified electrician.
This product is for use on a nominal 220-volt circuit and has a grounding plug.
Make sure that the product is connected to an outlet having the same
configuration as the plug.
zThis unit must be plugged into a nominal 220 volt 50/60 hz, which has a
grounding.
zKeep hands clear of all moving parts. Never place hands, feet under the
treadmill.
zDo not use the treadmill on a carpet that is greater than 1/2 inch in height.
zBefore using the treadmill, check that the running belt is aligned and
centered on the treadmill bed and all visible fasteners on the treadmill are
sufficiently tightened and secure.
WARNING:Before beginning any exercise program consult your
physician. This is especially important for the persons who are over 35 years
old or who have pre-existing health problems. Read all instructions before
using any fitness equipment. We assume no responsibility for personal injury
or property damage sustained by or through the use of this product. Do not
operate this exercise equipment without properly fitted guards, as the moving
parts can present a risk of serious injury to young children.
CAUTION:Read all instructions carefully before operating this
product. Retain this Owner’s Manual for future reference.

5
OVERVIEW DRAWING

6
PARTS LIST
Part # Description Quantity Part # Description Quantity
001 Main Frame 1 028 Nylon Nut (M6) 8
002 Stabilizer 1 029 Nylon Nut (M8) 3
003 Adjustable Pad (M8) 2 030 End Cap (40x50) 2
004 End Cap for Stabilizer 2 031 Upper Dust Cover 1
005 Bolt (M8x40) 2 032 Lower Dust Cover 1
006 Transportation Wheel
Ø53xØ8x23mm 2 033 Bolt (M4x30) 4
007 Bushing Ø42xØ10.5x5.5mm 2 034 Left Handlebar Support 1
008 Spacer 2 035 Right Handlebar Support 1
009 Running Deck 1 036 Handlebar 1
010 Front Roller 1 037 End Cap for Handlebar 2
011 Rear Roller 1 038 Computer 1
012 Running Belt 2220x367x1.6t 1 039 Computer Bracket 1
013 Motor Bracket 1 040 Bolt (M5x10) 4
014 Bushing 2 041 Safety Tether Key 1
015 Axis 1 042 Plastic Cover for Handlebar 2
016 Motor 1 043 Hex Socket Button Head Cap
Bolt (M8x45mm) 4
017 Bracket for Drive Motor 1 044 Square End Cap (□25) 1
018 Power Control Board 1 045 Foam Grip Ø30x3.5tx150mm 2
019 Belt 5PJ508 1 046 Spacer Ø16xØ10.5x19mm 2
020 Sensor 1 047 Cap Nut 2
021 Bracket for Sensor 1 048 Bolt (M10x85) 2
022 Switch, AC Power 1 049 Nylon Nut (M10) 2
023 Cover Ø38 2 050 Hex Socket Button Head Cap
Bolt (M8x16mm) 6
024 Side Rail 2 051 Cup Nut M8 4
025 Hex Socket Head Cap Bolt
(M6x60mm) 2 052 Safety Tube B 1
026 Tapping Screw (M4x16mm) 5 053 Safety Tube A 1
027 Bolt (M6x35) 8 054 Hex Socket Head Cap Bolt
(M8x40mm) 2

7
PARTS LIST
Part # Description Quantity Part # Description Quantity
055 Spring Washer (M8) 12 068 Tapping Screw (M3x20) 4
056 Nylon Washer (M8) 2 069 Bolt (M8x35) 1
057 Spring Knob 1 070 Bolt (M8x12) 2
058 Square End Cap (□20) 1 071 Wire for Fuse Box 1
059 Left Rear Cap for Main Frame 1 072 Bolt (M4x12) 3
060 Right Rear Cap for Main Frame 1 073 Sensor Cable I (650 mm.) 1
061 Fuse Box 1 074 Sensor Cable II (1100 mm.) 1
062 Power Cord 1 075 Sensor Cable III (550 mm.) 1
063 Wire Cap 1 076 Carriage Bolt M8x45 2
064 Nylon Nut (M4) 3 077 Hex Socket Button Head Cap
Bolt (M8x40mm) 1
065 Cable Switch/PCB 1 078 Bushing 1
066 Upper Hand Pulse Sensor
Cover w/Wire 2 079 Tapping Screw (M4x23mm) 1
067 Lower Hand Pulse Cap 2 080 Washer Ø20xØ10.5x1.0t 2
HARDWARE PACKING LIST
Part # Description Quantity
43 Hex Socket Button Head Cap Bolt
(M8x45mm)
50 Hex Socket Button Head Cap Bolt
(M8x16mm)
55 Spring Washer (M8)
4
6
6
Allen Wrench/Screwdriver
1 PC Wrench 1 PC
Silicone Oil
1 PC

8
ASSEMBLY INSTRUCTIONS
Step 1
Connect the Sensor Cable I (73) from the Stabilizer (2) to the Sensor Cable II
(74) from the Right Handlebar Support (35) and then attach the Right
Handlebar Support (35) to the Stabilizer (2) with three M8 Spring Washers (55)
and M8x16mm Hex Socket Button Head Cap Bolts (50).
Step 2
Attach the Left Handlebar Support (34) to the Stabilizer (2) with three M8
Spring Washers (55) and M8x16mm Hex Socket Button Head Cap Bolts (50).
Step 3 and 4
Connect the Sensor Cable II (74) from the Right Handlebar Support (35) to the
Sensor Cable III (75) from the Handlebar (36) and the attach the Handlebar
(36) onto the Right and Left Handlebar Supports (35, 34) with two Plastic
Covers for Handlebar (42) and M8x45 Hex Socket Button Head Cap Bolts
(43).
12
43

9
Step 5
Remove two M8x45 Carriage Bolts (76), M8 Spring Washers (55), and M8 Cup
Nuts (51) from the Computer Bracket (39). Then attach the Computer
Bracket (39) to the Handlebar (36) with two M8x45 Carriage Bolts (76), M8
Spring Washers (55), and M8 Cup Nuts (51) that were removed.
Step 6
Remove four M5x10 Bolts (40) from the Computer (38). Connect the Sensor
Cable III (75) and Upper Hand Pulse Sensor Wires (66) from the Handlebar
(36) to the socket and wire that come from the Computer (38) and then attach
the Computer (38) onto the Computer Bracket (39) with four M5x10 Bolts (40)
that were removed. Finally, install the Safety Tether Key (41) onto the
Computer (38).
56