Life Gear Mentor II User manual

cv: mentor II, magnetic/TREADMILL
Item No.: 40125
Owner’s Manual
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s manual for future reference.
The specifications of this product may vary from this photo, subject to change without notice.
2011, Jan.

1
TABLE OF CONTENTS
WARRANTY-------------------------------------------------------------------------------- 1
SAFETY INSTRUCTIONS-------------------------------------------------------------- 2
OVERVIEW DRAWING------------------------------------------------------------------3
PARTS LIST-------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST-----------------------------------------------------------5
TOOLS--------------------------------------------------------------------------------------- 5
ASSEMBLY INSTRUCTIONS----------------------------------------------------------6
OPERATING THE COMPUTER-------------------------------------------------------10
LIFTING UPAND SETTING DOWN THE TREADMILL------------------------- 12
ADJUSTMENTS---------------------------------------------------------------------------13
MAINTENANCE--------------------------------------------------------------------------- 14
TROUBLESHOOTING-------------------------------------------------------------------14
WARM UPAND COOL DOWN ROUTINE------------------------------------------15
ONE YEAR LIMITED WARRANTY
LifeGear Inc. warrants to the original purchaser that this product is free from defects in
material and workmanship when used for the purpose intended, under the conditions that it
has been installed and operated in accordance with LifeGear's Owner's Manual. LifeGear's
obligation under this warranty is limited to replacing or repairing, free of charge, any parts
which may prove to be defective under normal home use. This warranty does not include
any damage caused by improper operation, misuse or commercial application.
From the date of purchase, the frame is warranted to be free from defects for 1 (one) year.
This warranty is extended only to the original owner and is not transferable.
When ordering replacement parts please have the following information ready:
1. Owner's Manual
2. Model Number
3. Description of Parts
4. Part Number
5. Date of Purchase

2
SAFETY INSTRUCTIONS
Basic precautions should always be followed, including the following safety
instructions when using this magnetic treadmill: Read all instructions before using
this magnetic treadmill.
1. Check every part of the equipment before exercise. If there is any defective
component, replace it immediately; keep the equipment out of use until repair.
2. Make sure all parts, bolts and nuts are well assembled and locked before exercise.
3. Never insert any object into any opening.
4. Never operate this magnetic treadmill if it is not working properly. If it has been
dropped or damaged, or been exposed to water, return the appliance to a service center
for examination and repair.
5. Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise, discontinue use and consult an Authorized
Service Representative.
6. Wear comfortable and suitable clothing when using the treadmill. Do not use the
treadmill barefoot, in only socks or in sandals, always wear athletic shoes. Never wear
loose clothing because it could run the risk of getting caught in the treadmill.
7. Keep children and pets away from the equipment while in use.
8. Do not use the treadmill outdoors. This magnetic treadmill is for household use only.
9. Only one person should be on the treadmill while in use.
10. Keep the magnetic treadmill on a solid, level surface with the minimum safety area
clearance of 2000mm x 1000mm of the magnetic treadmill. Be sure the area around
the treadmill remains clear during use and has adequate clearance.
11. Hold the handlebar with your hands when starting or stopping exercise and increasing
or decreasing the speed.
12. If feeling chest pains, nausea, dizziness, or short of breath, you should stop exercising
immediately and consult your physician before continuing.
13. The maximum weight capacity for this product is 110kgs.
WARNING:Before beginning any exercise program consult your physician.
This is especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness
equipment.
CAUTION:Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

3
OVERVIEW DRAWING
52
17
54 53
50
49
59
48
56
19
20
18
16
1
3
50
59
58
16
16
17 48
18
58
60
59
16
2
57
60
13
11
10
7
12
4
5
6
4
5
13
15
14
8
9
4
5
9
45
7
6
12
13
13
15
14
29
22
8
28
29
28
8
41
42
21 44
55 98
43
27
47
46
26
26
24
25
25
29
23
29
32
9
8
33
34
36
35
31
30 8
932
33
31
34
36
35 40 8
9
37 39
38
8
9
51
41

4
PARTS LIST
No. Description Qty No. Description Qty
001 Right Handlebar Support Frame
513x40x1180 1 031 InclineAdjustment Frame End Cap Ø25x27 2
002 Left Handlebar Support Frame
513x40x1180 1 032 Bolt M8x38 2
003 Connection Support Frame
103x535x54 1 033 Locking Pin 2
004 Rubber Pad Ø33xØ38x16 4 034 Rear RollerAdjustment Bolt Plate 2
005 Bolt M6x16 4 035 Washer Ø6 2
006 Bolt M8x35 2 036 Rear RollerAdjustment Bolt M6x55 2
007 Wheel Ø50xØ8x20 2 037 Safety TubeA 1
008 Washer Ø8 9 038 Safety Tube B 1
009 Nylon Nut M8 7 039 Spring Knob 1
010 Nylon Nut M10 4 040 Bolt M8x42 1
011 Washer Ø10 4 041 Bolt M8x75 2
012 Bolt M10x40 4 042 Magnet 4
013 End Cap (25x50) 4 043 Hex Head Bolt M5x25 1
014 Washer Ø12 2 044 Magnet Bracket 1
015 Bolt M12x65 2 045 Square End Cap (25x25) 1
016 Hand Pulse Sensor with Wire 2 046 Sensor with Wire 100mm 1
017 Foam Grip Ø28xØ23x280 2 047 Screw ST2.9x9.5 2
018 Screw M4x15mm. 2 048 Bolt M6x12 2
019 Computer RZW081 1 049 Handlebar 1
020 Bolt M5x10 2 050 Handlebar End Cap Ø25 2
021 Main Frame 1 051 Nut M8 2
022 Front Roller Ø160xØ42x445 1 052 Tension Control Knob L=1080mm 1
023 Rear Roller Ø42x443 1 053 Curve Washer for Tension Control
Knob Ø5 1
024 Running Belt 360x2532x1.3 1 054 Bolt for Tension Control Knob
M5x25 1
025 Side Rail 30x1056x2 2 055 Spring 1
026 Bolt M5x25 8 056 Wire Plug Ø25xØ13x4 1
027 Running Deck 1114x458x12 1 057 Wire Plug Ø12 1
028 Bolt M8x15 2 058 Sensor Cable I (L=450mm) 1
029 Front Roller Sleeve 4 059 Sensor Cable II (L=450mm) 2
030 Incline Adjustment Frame
511x24x124 1 060 Sensor Cable III (L=1000mm) 1

5
HARDWARE PACKING LIST
TOOLS
Allen Wrench #5
1 PC
Multi Hex Tool S13, S17, S19
2 PCS
Multi Hex Tool with Phillips Screwdriver
1 PC
(10) Nylon Nut M10
4 PCS (11) Washer Ø10 4 PCS (12) Bolt M10x40 4 PCS
(14) Washer Ø12
2 PCS (15) Bolt M12x65 2 PCS (48) Bolt M6x12 2 PCS

6
ASSEMBLY INSTRUCTIONS
Step 1
Attach the Connection Support Frame (3) onto the Right/Left Handlebar Support Frames
(1, 2) with four M10 Nylon Nuts (10), Ø10 Washers (11), and M10x40 Bolts (12). Tighten
bolts with two Multi Hex Tools provided.
Hardware:
2
1
12
12
11
10
10
11
3
10
10
11
11
12
12
2 Multi Hex Tools (S13, S17, S19)
Tool:
4 Nylon Nuts (M10) 4 Washers (Ø10) 4 Bolts (M10x40)

7
Step 2
Connect the Hand Pulse Sensor Wire (16) from the Right Handlebar Support Frame (1) to
the Sensor Cable II (59) from the Handlebar (49).
Connect the Hand Pulse Sensor Wire (16) and Sensor Cable III (60) from the Left
Handlebar Support Frame (2) to the Sensor Cable II (59) and Sensor Cable I (58) from the
Handlebar (49).
Attach the Handlebar (49) into the Right/Left Handlebar Support Frames (1, 2) with two
M6x12 Bolts (48). Tighten bolts with the Allen Wrench provided.
Remove two M5x10 Bolts (20) from the Computer (19). Connect the Sensor Cable I (58)
and Sensor Cables II (59) from the Handlebar (49) to the wires that come from the
Computer (19).
Attach the Computer (19) onto the plate of the Handlebar (49) with two M5x10 Bolts (20) that
were removed. Tighten bolts with the Multi Hex Tool with Phillips Screwdriver provided.
Hardware:
19
49
1
2
60
59
16
48
48
58
59
16
60
20
59
58
Allen Wrench #5
Multi Hex Tool with Phillips Screwdriver
Tool:
2 Bolts (M6x12)

8
Step 3
Attach the Main Frame (21) onto the Right/Left Handlebar Support Frames (1, 2) with two
Ø12 Washers (14) and M12x65 Bolts (15). Tighten bolts with two Multi Hex Tools provided.
Connect the Sensor Wire (46) from the Main Frame (21) to the Sensor Cable III (60) from
the Left Handlebar Support Frame (2).
NOTE: It is recommended that you always use the aid of a second person when
assembling the treadmill.
Hardware:
2 Washers (Ø12) 2 Bolts (M12x65)
2 Multi Hex Tools (S13, S17, S19)
Tool:
1
2
60
46
21
1514
14
15
52

9
Step 4
Remove one Ø8 Washer (8), M8 Nylon Nut (9), M8x75 Bolt (41), and two M8 Nuts (51) from
the Safety Tube B (38).
Remove one Ø8 Washer (8), M8 Nylon Nut (9), and M8x42 Bolt (40) from the Safety Tube A
(37).
Attach the Safety Tube B (38) onto the Left Handlebar Support Frame (2) with one Ø8
Washer (8), M8 Nylon Nut (9), M8x75 Bolt (41), and two M8 Nuts (51) that were removed.
Tighten bolt and nylon nut with a Allen Wrench and Multi Hex Tool with Phillips Screwdriver
provided.
Attach the Safety Tube A (37) onto the Main Frame (21) with one Ø8 Washer (8), M8 Nylon
Nut (9), and M8x42 Bolt (40) that were removed. Tighten bolt and nylon nut with a Allen
Wrench and Multi Hex Tool with Phillips Screwdriver provided.
Allen Wrench #5
Multi Hex Tool with Phillips Screwdriver
Tool:
2
21
38 37
41
51
89
8940