Light Emotion thunderboltg2 Operator's manual

User’s instruction manual
This manual contains important information about the safe installation and use of this product
Please read this instruction manual carefully before installing or operating
Please keep these instructions in a safe place for future reference

Introduction
Thanks for choosing our laser device, believing this brand new product will bring you unlimited marvel and
happiness. Before operating this device, please read this manual thoroughly, and retain it for future reference.
CAUTION
Please read this anual fully before installing or operating this product as it contains i portant
safety infor ation relating to its installation and operation.
This Class 3B laser product e its hazardous levels of optical radiation and will cause injury to
the eyes if viewed directly.
This product is not suitable for projection directly at audiences or other personnel.
This product ust not be used for any for of audience scanning application and is for
professional use only.
I portant infor ation
This product is a Class 3B laser and should only be installed and used by personal who are trained in the
management of laser radiation and are able to operate in accordance within the guidance given by the Health
and Safety xecutive (HS ) in HS(G)95: “The Radiation Safety of Lasers used for Display purposes”.
This product contains no user-serviceable parts. Under no circumstances should any attempt be made by the
user to dismantle or modify it in any way.
Installation instructions
This product must be securely mounted with adequate fixings to hold the weight. If mounted at height, use a
safety wire attached to the eyebolt and a secondary fixing point. Position the aperture so that its emission is
always directed away from people and objects that are able to reflect the emission towards people. In this
regard the separation distances of 3 metres vertically and 2.5 metres horizontally, cited in HS(G)95 and shown
below must be observed.
Vertical bird’s eye view

Vertical cross sectional view
Unpacking
Please check the contents to ensure that the product has been received in good condition.
Laser x 1 unit
I.R. remote control x1 pc
I C Power Lead x 1pc
Safety Keys x2pcs
If you find any accessory is missing or the product has arrived with any problems, please contact your retailer
at once.
This product contains no user-serviceable parts so make no attempt to try to fix or modify this item yourself as
this will invalidate the warranty. We recommend you keep the original package and proof of purchase for any
possible replacement or returned demand.
Setting up
1. Unpack the laser ensuring all packaging and tape is removed.
2. Always test the laser before fixing in a permanent location.
3. Connect the I C mains plug and switch the rear power switch on.
4. Insert the safety key and turn to a quarter turn clockwise. At this point ensure that no one is exposed to
laser radiation.
5. Select which mode you want to operate the laser in.
6. Leave the laser to run for 10 minutes before installing in its location.
Installation
When mounting at height, attach a safety wire to the eyebolt with an independent fixing.
Use the integral mounting bracket with a suitable clamp for stand or truss being fixed to. When mounting
directly to ceiling surfaces, be sure to use adequate fixings for the supporting material.

Connecting to ains, earth wire (ground) ust be connected.
Use the supplied I C lead to connect to the main power supply as follows:
Wire
Connection
International symbol
B
rown
Live
L
B
lue
Neutral
N
Yellow/Cyan
arth
For your safety, please kindly pay attention to all of the warnings below:
 Always plug in the power plug last and disconnect from the mains when the device is not in use or before
cleaning.
 Do not install and operate the device in rain or extreme heat, moisture or dusty environments.
 This device is for indoor use only and in a dry environment.
 Do not switch on immediately. Wait until the unit reaches room temperature.
 Do not shake the device and avoid brute force when installing or operating.
 Do not use the device during thunderstorms and please disconnect the power.
 Do not use solvents or aggressive detergent to clean the device. Use a soft and clean cloth.
 Do not modify the device or the connected power cord without authorisation.
 Do not stare into the aperture. This product emits hazardous levels of optical radiation and will cause serious
injury to the eyes if viewed at close range.
 This product should be securely mounted so that its output emission is always directed away from people
and at objects that are able to reflect emission towards people. In this regard, the separation distances cited in
HS(G)95 should be observed.
 The symbol determines the minimum distance from lighted objects. The minimum distance
between light-output and the illuminated surface must be more than 0.5m.

Replacing the fuse
First disconnect from the mains power supply then remove the fuse holder above the I C Socket to reveal the
fuse. Replace with the correct fuse rating as stated on the product or in the user manual. Then lock the fuse
holder cover back into place.
General aintenance
Be sure to power off the fixture before conducting maintenance.
To maintain optimum performance and minimize wear, fixtures should be
cleaned frequently.
Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be
cleaned at least twice a month. Dust build-up reduces light output & performance as well as overheating. This
can lead to reduced life and increased mechanical wear.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust collected on
external vents and internal components. Clean all glass when fixture is cold with a mild solution to the cloth or
tissue, and drag dirt and grime to the outside of the lens. Gently polish optical surfaces until they are free of
haze and lint.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize
light output. Cleaning frequently depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surroundings can require cleaning fluid. Always dry the parts carefully. Clean the external
optics at least every 20 days.
Front panel
1. Laser aperture
2. Power L D
3. I.R. remote receiver
4. Music L D
Rear Panel
5. I C mains inlet
6. Mains fuse holder
7. Power switch
8. Remote power connector
9. Safety eyebolt
10. Safety lock
11.Cool fan
12. DMX input
13. DMX output
14 Contorl panel
15. Internal microphone
16. Sensitivity

Control panel
The control panel and display allow the user to adjust settings as follows…
 Press MOD to navigate through the options
 Press NT R to select an option and adjust value using UP and DOWN buttons
 Press NT R again to confirm setting
Control panel options
Display Mode
P
ress ENT for
setting(press MODE
to exit)
Auto Auto modes
Sound Sound activated modes
d001 DMX start address
SLAU Slave mode
Stand-alone odes
TH laser can operate in stand-alone mode one of 2 ways: Auto or Sound-activated
Auto Show / Stand Alone ode (Auto)
1 Press the function button (Func) to enter Mode options
2 Press the function button until the L D panel shows Auto
3 Press the nter button to confirm the setting The laser will now be working in Auto Show / Stand Alone
mode
Sound Activated / Sound-to-Light / Stand Alone ode (Sound)
1 Press the function button (MOD ) to enter Mode options
2 Press the function button until the L D panel shows Sound
3 Press the nter button to confirm the setting The laser will now be working in Sound Activated
DMX ode
1 Press the function button (mode) to enter Mode options
2 Press the function button until the L D panel shows d001
3 Press the nter button to confirm the setting or change the address using the Up and Down buttons 4 Press
the nt button to confirm the setting The laser will now be working in DMX mod
DMX ode / DMX address setting
1 nsure the unit is in DMX mode (see above)
2 Press the Up or Down buttons to adjust the DMX address
3 Press the nter button to confirm the setting
If multiple connected units are to be controlled in exactly the same way, set all units to the same starting
address (e.g. 001). If individual control of multiple connected units is required, each unit must have its own
starting address. This address must be at least 10 channels apart e.g. set the first unit to 001 and the second
unit to 011, the third unit to 021 and so on. The DMX controller will now control all the connected units
separately.

Master/Slave ode
1 Press the function button (MOD ) to enter Mode options
2 Press the function button until the L D panel shows SLA
3 Press the nter button to confirm the setting
The laser will now be working in Slave mode
To create a Master/Slave chain of units, one laser has to be designated as the Master unit whilst the remaining
units have to be set as Slave units. To set the Master unit, choose one laser and set it to your desired mode
(Auto mode, Sound-to-Light mode, etc). Next connect all other units via DMX cables. To achieve this, join the
DMX output of one unit to the next unit’s DMX input until all lasers are connected. Set all the Slave units to
Slave mode (see above). The Slave lasers will now duplicate the actions of the Master unit.
Microphone sensitivity
In sound-activated mode, the sensitivity of the internal microphone can be adjusted via the control panel. To
set the sensitivity level, do the following…
Re ote control ode
The laser can be operated using the supplied handheld infra-red remote
control.
To use this remote control, firstly, remove the plastic tab at the bottom of the
remote to activate the internal battery. If necessary, this can be replaced with a
standard CR2025 button cell.
DMX MODE
The laser is equipped with 3-pin XLR connectors for DMX input and output. These connectors are wired in
parallel. Only use a shielded twisted-pair cable designed for 3-pin XLR-plugs and connectors in order to
connect the controller with the fixture or one fixture with another.
Caution: At the last fixture, the DMX-cable has to end with a terminator.
Solder a 120 Ohm resistor between PIN 2 (-) and PIN 3 (+) into a 3-pin XLR-plug and plug it in the DMX-output
of the last fixture.
A
On/Off
button
Press button to turn laser On or Off
B
Music mode
Press button to activate Sound
-
to
-
Light mode
C
Auto mode
Press b
utton to activate Auto mode
D/
Colo
r
buttons
Press buttons to cycle
through laser’s available colo
rs
F
Pause button
Press button to pause the laser effect
G
Pattern buttons
Press the A and C buttons to change the laser patterns
Use the 0
-
9 di
git buttons to choose any pattern from 1 to
32
H
Pattern repeat
Press button to cycle repeat the last and current patterns

CH 1
CONTROL MOD
000-063 BLACK OUT
063-127 AUTO SHOW
128-191 MUSIC SHOW
192-255 DMX MOD
CH2
GOBOS 0-255 Split 32 patterns
CH3
ZOOM
0-127 100%-5%
128-169 Zoom out mode
170-209 Zoom in mode
210-255 Zoom out and Zoom in mode
CH4
L FT RIGHT TURN
000-127 0-359 Degree
128-255 Clockwise Mode
192-255 Anticlockwise Mode
CH5
UP DOWN TURN
000-127 0-359 Degree
128-191 Clockwise Mode
192-255 Anticlockwise Mode
CH6
ROTAT
000-127 0-359 Degree
128-191 Clockwise Mode
128-255 Anticlockwise Mode
CH7
L FT RIGHT MOV
000-127 Left Right position, total 128 position
128-191 Clockwise Move Mode
128-255 Anticlockwise Move Mode
CH 8
UP DOWN MOV
000-127 Up Down position, total 128 position
128-191 Clockwise Move Mode
128-255 Anticlockwise Move Mode

Specifications
Important: This product conformed to Laser & LED Safety standard BSEN60825- 2007
incorporating corrigendum 2008
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed
as lectrical or lectronic equipment and should not be disposed with other household or
commercial waste at the end of its useful life.
Model THUNDERBOLTG2
Green
DPSS 532nm 50mW
Laser level Class 3B Laser
Dimensions 225x 85x80mm
Weight 2 KG
Power supply 100-240Vac,
50/60Hz(IEC)
consumption 20W
Fuse rating 250V A Slow Blow (20mm Glass)
Operating temperature 10-40
℃
Channel Range 1-9
Remote control battery C 2025 button cell