Lightmybricks LEGO Land Rover Defender 42110 User manual

42110

Package Contents:
8x Cool White 30cm Bit Lights
4x Red 30cm Bit Lights
2x White Strip Lights
1x 6-Port Expansion Board
1x 12-Port Expansion Board
1x 15cm Connecting Cables
2x 30cm Connecting Cables
6x Adhesive Squares
1x AA Battery Pack
LEGO Pieces:
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid
correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables;
instead ensure they are laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be
inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on
the left side of the port. The connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do
not force it.

Incorrectly inserting the connector can can result in bent pins inside the port or possible
overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the
connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector,
don’t force it. Doing so will damage the plug and the connector.
Connecting Micro Cable connectors to Micro Expansion Board
Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards.
Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables
to Strip Lights. With the expansion board facing up, ensure the side of the connector with the
wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.

Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up
(Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in
between.

OK, Let’s Begin!
1.) Lift up the bonnet, then remove the following sections in order for us toremove the two
headlight sections as shown below.

2.) Take the right headlight section (passenger side) and disassemble it as perbelow, then
take a Cool White 30cm Bit Light and thread the connector end of it through the front of the
round dish. Thread the cable all the way through until the LED is about 1cm away from the front
of the dish. Turn the LED over so that it is facing forward.

Take another Cool White 30cm Bit Light and thread it through the front of the dish, same way
we did for the first light.

3.) Continue threading another 2x Cool White 30cm Bit Lights through the dish, then take
LEGO Bar we removed earlier and insert it through the technic axle hole. Ensure the cables are
laid in the technic axle spaces, to prevent them from being damaged when inserting the bar.
Reposition the 4 LEDs so they are evenly spaced out and positioned over the circles on the
stickers behind, then reconnect the trans clear dish over the top.
Reconnect the headlight to the rest of this section via the technic bar.

4.) Turn this section around and bring the 4 cables across to the right sideunderneath the
technic pin. Bring this section over to the left side of the vehicle and thread the cables in
between the two sections as shown below. Reconnect the headlight via the technic vertical axle.

Group the 4 cables together and thread them down the following space behind the front grill.
Prop the vehicle up using your light kit box, then pull the cables down from underneath as
shown below.

5.) Flip the vehicle over and thread the four cables through the following spaceunderneath
the technic bars, pulling them all the way out from the other side as shown below.

Turn the vehicle around to the side, and bring the cables back over and loop them around the
wheel axis 3-4 times to eliminate excess cables, then connect them to the 12-Port Expansion
Board

Take the AA Battery Pack and insert 3x new AA batteries to it. Connect the battery pack cable to
a spare port on the 12-port expansion board then turn it ON to test the right headlights are
working OK.
Note: If you experience any issues with the lights not working and suspect an issue with a
component, please try a different port on the expansion board to verify where the fault lies
(with the light, expansion board or effects board). To correct any issues with expansion board

ports, please view the section addressing expansion board issues on our online troubleshooting
guide.
6.) Take the following remaining head light sections and reassemble andconnect them back
to the front of the vehicle. Reconnect all the sections we disconnected earlier from the right
side.