Lightmybricks 75252 User manual

Please note: This page lists instructions for the LED light kit only.
Package Contents:
34x Cool White 30cm Bit Lights
3x Flashing White 30cm Bit Light
4x Flashing Red 30cm Bit Light
5x Cool White 30cm Large Bit Lights
20x Green 15cm Micro Bit Lights
11x White 30cm Micro Bit Lights
Effects and Expansion Boards
1x Pulse Effects Board
1x Gun Effects Board
1x Multi Effects Board
1x Flicker Effects Board
7x Micro 4-Port Expansion Boards
1x Micro 8-Port Expansion Boards
1x 2-Port Expansion Board
6x 6-Port Expansion Boards
1x 8-Port Expansion Boards
3x 12-Port Expansion Boards
Connecting Cables:
9x 5cm Connecting Cables
6x 15cm Connecting Cables
5x 30cm Connecting Cables
2x 50cm Connecting Cable 1x USB
Power Cable

LEGO Pieces:
28x Trans Clear Round Plate 1×1
4x Trans Light Blue Round Plate 1×1
1x Trans Clear Tile 1×2
1x Trans Black Cone 1×1 with Top Groove
1x Trans Clear Slope 30 1x1x2/3
Important things to note:
Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they are laid
correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables;
instead ensure they are laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be
inserted only one way. With the expansion board facing up, look for the soldered “=” symbol on
the left side of the port. The connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t fit easily into a port connector, do
not force it.
Incorrectly inserting the connector can can result in bent pins inside the port or possible
overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the
connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector,
don’t force it. Doing so will damage the plug and the connector.

Connecting Micro Cable connectors to Micro Expansion Board
Ports
Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards.
Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables
to Strip Lights. With the expansion board facing up, ensure the side of the connector with the
wires exposed is facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights under LEGO® bricks and plates.

When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow
LED component exposed). You can either place them directly on top of LEGO® studs or in
between.
OK, Let’s Begin!
1.) Start by disconnecting the following sections from the top of the ship.

Use your LEGO removal tool to disconnect the following pieces to allow us to remove the
two panels that make up the entire left section of the ship.

Disconnect the Tantive via the trans clear clip

2.) We will now install seven lights along the side of the ship. Take a Cool White 30cm Bit Light
and with the cable facing up, place it over the following stud near the front of the ship.
Secure the Bit Light in place by connecting a provided Trans Clear Round Plate 1×1 over the
top.

Bring the cable over towards the inside of the ship, then feed the cable underneath the
following technic pieces.
3.) Take out another Cool White 30cm Bit Light and install it to the next stud down the side of
the ship as shown below. Secure it in place with another provided Trans Clear Round Plate
1×1. Feed the cable underneath the technic pieces as we did for the previous bit light cable.

4.) Using the same method used in previous steps, install another 2x Cool White 30cm Bit
Lights to the following studs along the side of the ship. Follow the images below to ensure
you install the lights to the correct location. Secure them in place using 2x Trans Clear
Round Plates 1×1. Once installed, lay the cables inside toward the first two Bit Light cables.

5.) Take a 12-Port Expansion Board and connect the four Bit Light Cables, then take a 50cm
Connecting Cable connect it to another spare port on the 12-Port Expansion Board.

Bring the other end of the 50cm connecting cable toward the back of the ship and feed it
underneath the large red technic plate sections going across the centre. Pull the cable out
from the other side and connect it to a new 12-Port Expansion Board.

6.) We will now install another three lights to the side of the ship to thefollowing positions.

First disconnect the following pieces, then install a Cool White 30cm Bit Light to the following
stud, securing it in place using a provided Trans Clear Round Plate 1×1. Once installed,
reconnect the pieces we removed earlier.