Lightmybricks Downtown Diner Lighting Kit User manual

Light My Bricks
Installation Instructions for Light My Bricks LED Lighting Kits
Mar 1 ·28 min read · Unlisted
Light My Bricks: Downtown Diner
Lighting Kit
The following page is instructions for the Light My Bricks LEGO
Downtown Diner (10260) LED light kit. You purchase this kit on our
ocial website.
To ensure a trouble-free installation of your light kit, please read and
follow each step carefully.
If you run into any issues, please refer to the online troubleshooting
guide.
This user guide is also available to download in PDF format here.
...

Package contents:
1x LEGO Lamp Post with Bit Light installed
3x Flashing White 30cm Bit Lights
1x White 30cm Bit Light
7x White 15cm Bit Lights
11x White Strip Lights
2x 8-Port Expansion Boards
1x 6-Port Expansion Board
5x 5cm Connecting Cables
5x 15cm Connecting Cables
2x 30cm Connecting Cables
1x 50cm Connecting Cable
4x Adhesive Squares
AA Battery Pack (Requires 3x AA Batteries)
LEGO Pieces
2x Trans Clear Round Plate 1x1
5x Trans Red Round Plate 1x1
5x Plate 1x6 (for mounting strip lights)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
...
Important things to note:
Laying cables in between and underneath bricks
Cables can t in between and underneath LEGO® bricks, plates, and
tiles providing they are laid correctly between the LEGO® studs. Do
NOT forcefully join LEGO® together around cables; instead ensure they
are laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a cable
can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion
Boards. Connectors can be inserted only one way. With the expansion
board facing up, look for the soldered “=” symbol on the left side of the
port. The connector side with the wires exposed should be facing
toward the soldered “=” symbol as you insert into the port. If a plug
won’t t easily into a port connector, do not force it.

Incorrectly inserting the connector can can result in
bent pins inside the port or possible overheating of
the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing
up, ensure the side of the connector with the wires exposed is facing
down. If a plug won’t t easily into a port connector, don’t force it.
Doing so will damage the plug and the connector.

Installing Bit Lights under LEGO ® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed
the correct way up (Yellow LED component exposed). You can either
place them directly on top of LEGO® studs or in between.
...
OK, Let’s Begin!
Lighting the Car

1.) Start by disconnecting the following sections of the front and
bottom of the car (trans clear tiles, 1x12 plates, and front bumper
section).

2.) Take a White 15cm Bit Light and with the cable facing down, place
it directly over one of the front grey studs. Take a provided Trans Clear
Round Plate 1x1 and connect it over the top to secure the Bit Light in
place.
Install another White 15cm Bit Light to the other headlight using the
same method as above.

3.) Lay both Bit Light cables down the side of the White 2x4 plate and
then reconnect the front bumper section over the top.
Bring both cables down the base of the car and then thread each cable
through the spacing in between the back wheel and side of car.

Pull each cable up from the inside of the car.
4.) Reconnect the two 1x12 plates ensuring you secure each cable in
between studs of each plate.